Difference between revisions of "HRRL Positron Rotating W Target"

From New IAC Wiki
Jump to navigation Jump to search
 
(65 intermediate revisions by 4 users not shown)
Line 1: Line 1:
=45 degree angle=
+
[[PositronTargetWorkByChrissJackson]]
 +
 
 +
=Target Construction=
 +
 
 +
Current beam line distances for target to be inserted into
 +
 
 +
[[File:hrrl_e+_Target_area_Space.png | 400 px]]
 +
 
 +
==Motor==
 +
 
 +
[[File:HRRL_Beam_Rot_Tar_Sys_Mot1.png | 400 px]]
 +
 
 +
Empire Magnetics Model U42
 +
 
 +
;Wiring Diagram:[[Media:U-42EmpireMagneticsMotorWiringDiag.pdf]]
 +
 
 +
[http://www.youtube.com/watch?v=pS0cBeT_trE&context=C41942f6ADvjVQa1PpcFPVZGpWjIhpT6B3B7hDLZHuaQKYXRQ0xVc= Motor test video 1]
 +
 
 +
[http://www.youtube.com/watch?v=En2mQlIkufA&context=C489b379ADvjVQa1PpcFPVZGpWjIhpT2TjUnFPiVQJteDyjBCk9cg= test video 2]
 +
 
 +
[http://www.youtube.com/watch?v=jeV11UtdtxU&context=C4b683ecADvjVQa1PpcFPVZGpWjIhpT3wsAPHTaPLebK8Mca7ahRg= test video 3]
 +
 
 +
[http://www.youtube.com/watch?v=PVv4XavFNfw&context=C4645105ADvjVQa1PpcFPVZGpWjIhpT_b2hBEuqINhOmJtWj57qxg= test video 4]
 +
 
 +
[http://www.youtube.com/watch?v=VeXNV1EX5Vc&context=C4d73946ADvjVQa1PpcFPVZGpWjIhpT6B3B7hDLZHuaQKYXRQ0xVc= test video 5]
 +
 
 +
==Motor Controller==
 +
 
 +
===Power supply===
 +
 
 +
[http://www.lamonde.com/acatalog/Products_Power_Supplies_992.html#aSTP_2dPWR_2d4810 Power Supply STP-PWR-4810 Power supply for stepping systems, dual output with 48 VDC @ 10A (at full load) unregulated and 5 VDC at 0.5A regulated.]
 +
 
 +
===STR8 ===
 +
 
 +
[[file:STR8.png | 300 px]]
 +
 
 +
STR8 Manuals:
 +
 
 +
[[Media:STR_Hardware_Manual.pdf]]
 +
 
 +
[[Media:STR_Quick_Setup_Guide.pdf]]
 +
 
 +
Datasheet:
 +
 
 +
[[Media:STR_Brochure_925-0002_RevC.pdf]]
 +
 
 +
=Design=
 +
 
 +
==  Documents ==
 +
 
 +
[[File:BRACKET_TUBE_END_SUPPORT_1.pdf]]
 +
 
 +
[[File:CAP_FITTING.pdf]]
 +
 
 +
[[File:CONE_TAPER_LOCK.PDF]]
 +
 
 +
[[File:COOLING_COOL_A_HELICAL.PDF]]
 +
 
 +
[[File:FERRULE_1.PDF]]
 +
 
 +
[[File:FITTING_ASSY_1_ISO_CUT_AWAY_2.PDF]]
 +
 
 +
[[File:FITTING_MAIN_BODY.PDF]]
 +
 
 +
[[File:HOSE_CLAMP.PDF]]
 +
 
 +
[[File:HUB_PEMSERT_ASSY.PDF]]
 +
 
 +
[[File:HUB_TAPER_LOCK.PDF]]
 +
 
 +
[[File:S VSRH_U42_RTD_110726A_SYSTEM_LAYOUT.pdf]]
 +
 
 +
[[File:S VSRH_U42_RTD_HS.PDF]]
 +
 
 +
 
 +
 
 +
==45 degree angle==
  
 
The Tungsten target should make a 45 degree angle with the beam.
 
The Tungsten target should make a 45 degree angle with the beam.
Line 6: Line 82:
  
  
=Beam Heat Load=
+
==Beam Heat Load==
  
 
;Accelerator Settings
 
;Accelerator Settings
Line 29: Line 105:
 
''P'' = (10 MeV) <math>\times</math> (60 <math>\mu</math>A) = 600 Watts.
 
''P'' = (10 MeV) <math>\times</math> (60 <math>\mu</math>A) = 600 Watts.
  
=Target Chamber design=
+
==Target Chamber design==
 +
 
 +
Latest Design From empire and Sadiq's measurement of the available space
 +
 
 +
 
 +
 
 +
{| border="1" cellpadding="20" cellspacing="0"
 +
|-
 +
|[[File:EmpMagHRRLPositronTargetChamberDrw_9-20-11.png | 200 px]]||[[File:HRRLPositronTargetSpace_10-5-11.png | 200 px]] || [[File:HRRLPositronTargetCoupler_10-5-11.png | 200 px]]|| [[File:HRRLPositronTargetHub_10-5-11.png | 200 px]]
 +
|-
 +
| Target motor Design  || Available beam line space || Motor axle coupling to rotary union || Hub and spline to attache targets
 +
|}
 +
 
  
 
;Dimensions are in inches
 
;Dimensions are in inches
Line 46: Line 134:
  
  
Latest Design From empire
 
  
[[File:EmpMagHRRLPositronTargetChamberDrw_7-25-11.png | 200 px]][[File:HRRLPositronTargetSpace_10-5-11.png | 200 px]]
+
July Design From empire
 +
 
 +
[[File:EmpMagHRRLPositronTargetChamberDrw_7-25-11.png | 200 px]]
  
 
{| border="1" cellpadding="20" cellspacing="0"
 
{| border="1" cellpadding="20" cellspacing="0"
Line 57: Line 146:
 
|}
 
|}
  
=Gate Valve - Target distance=
+
==Gate Valve - Target distance==
  
 
The distance from the front of the gate valve to the most beam upstream part of the target chamber is
 
The distance from the front of the gate valve to the most beam upstream part of the target chamber is
Line 68: Line 157:
 
So water would need to travel at a speed of 88.43 cm/0.7 sec = 1.26 m/sec
 
So water would need to travel at a speed of 88.43 cm/0.7 sec = 1.26 m/sec
  
= Properties of Tungsten=
+
== Properties of Tungsten==
  
 
*Melting Point = 3695 K.
 
*Melting Point = 3695 K.
Line 79: Line 168:
 
*Heat loss due to radiation: ( \sigma T^4)
 
*Heat loss due to radiation: ( \sigma T^4)
  
=Tungsten Temperature as a function of heat load=
+
==Tungsten Temperature as a function of heat load==
  
 
*IAC beamline pressure = <math>10^{-8} </math> Torr
 
*IAC beamline pressure = <math>10^{-8} </math> Torr
Line 87: Line 176:
 
*Conduction and Radiation
 
*Conduction and Radiation
  
=Calculating Radiators Equilibrium Temperature=
+
==Calculating Radiators Equilibrium Temperature==
  
==1.Calculating number of particles per second ==
+
===1.Calculating number of particles per second ===
  
 
We have electron beam of:
 
We have electron beam of:
Line 114: Line 203:
  
  
==2.Calculating Energy deposited per second==
+
===2.Calculating Energy deposited per second===
  
 
If we find the energy deposited by each electron and multiply to the total number of electrons in each second, we will find the total energy per second deposited in radiator.
 
If we find the energy deposited by each electron and multiply to the total number of electrons in each second, we will find the total energy per second deposited in radiator.
Line 129: Line 218:
 
Stopping power can be found from nuclear data tables <math> (dE/dx)_{ave} </math> and thickness is 0.001 times of radiation length. From Particle Data group we got radiation length and average total stopping powers around 15MeV for electrons in these materials from National Institute of Standards and Technology: [http://physics.nist.gov/PhysRefData/Star/Text/ESTAR.html Tungsten Stopping Power].
 
Stopping power can be found from nuclear data tables <math> (dE/dx)_{ave} </math> and thickness is 0.001 times of radiation length. From Particle Data group we got radiation length and average total stopping powers around 15MeV for electrons in these materials from National Institute of Standards and Technology: [http://physics.nist.gov/PhysRefData/Star/Text/ESTAR.html Tungsten Stopping Power].
  
===Table of Radiation Lengths===
+
====Table of Radiation Lengths====
 
Note:These data is from Particle Data group,Link: [http://pdg.lbl.gov/AtomicNuclearProperties/].
 
Note:These data is from Particle Data group,Link: [http://pdg.lbl.gov/AtomicNuclearProperties/].
  
Line 143: Line 232:
 
|}<br>
 
|}<br>
  
===Table of energy calculations===
+
====Table of energy calculations====
 
For the thickness of 0.001 Radiation Length (0.0001RL) of radiators.  
 
For the thickness of 0.001 Radiation Length (0.0001RL) of radiators.  
 
Note: <math>(dE/dx)_{coll}</math> is from National Institute of Standards and Technology. Link:  [[http://physics.nist.gov/PhysRefData/Star/Text/ESTAR.html]])
 
Note: <math>(dE/dx)_{coll}</math> is from National Institute of Standards and Technology. Link:  [[http://physics.nist.gov/PhysRefData/Star/Text/ESTAR.html]])
Line 163: Line 252:
 
                                           <math>P_{dep}= E_{dep}/s = ( E_{(dep~by~one)})\times(Number~of~electrons~per~second)</math>
 
                                           <math>P_{dep}= E_{dep}/s = ( E_{(dep~by~one)})\times(Number~of~electrons~per~second)</math>
  
==3.Calculating equilibrium temperature using Stefan–Boltzmann law==
+
===3.Calculating equilibrium temperature using Stefan–Boltzmann law===
 
If we assume that there is no energy conduction and total energy is just radiated from two surfaces of the radiators which are as big as beam spot,in our case beam spot is 2mm in diameter.  According to Stefan–Boltzmann law, this total power radiated will be
 
If we assume that there is no energy conduction and total energy is just radiated from two surfaces of the radiators which are as big as beam spot,in our case beam spot is 2mm in diameter.  According to Stefan–Boltzmann law, this total power radiated will be
 
   
 
   
Line 178: Line 267:
  
  
=Vendors=
+
==Vendors==
  
  
==MDC Target Chamber==
+
===MDC Target Chamber===
  
 
Target chamber: MDC vacuum products can send a prefab one you just need to weld up.
 
Target chamber: MDC vacuum products can send a prefab one you just need to weld up.
Line 204: Line 293:
 
MDC does not have a fast closing gate valve.  Model GV1500 closes in 0.7 seconds and costs $1600.  One that closes in 10 msec costs about $10k
 
MDC does not have a fast closing gate valve.  Model GV1500 closes in 0.7 seconds and costs $1600.  One that closes in 10 msec costs about $10k
  
==Tungsten Disks==
+
===Tungsten Disks===
  
 
;Dimensions are in cm
 
;Dimensions are in cm
Line 243: Line 332:
 
<math>\alpha = \frac{5.65 N m}{0.4 kg m^2} = 14.4 rad/sec \times \frac{1}{2 \pi} = 2.3 cycles/sec</math>
 
<math>\alpha = \frac{5.65 N m}{0.4 kg m^2} = 14.4 rad/sec \times \frac{1}{2 \pi} = 2.3 cycles/sec</math>
  
==Brushless Motor==
+
===Brushless Motor===
 +
 
 +
====Motor wiring diagram====
 +
 
 +
[[Media:U-42EmpireMagneticsMotorWiringDiag.pdf]]
  
  
Line 280: Line 373:
 
at each end,  technically it is feasible,  it's an issue of engineering
 
at each end,  technically it is feasible,  it's an issue of engineering
 
resource to chase them down,  get a quote then propose it to you,  so
 
resource to chase them down,  get a quote then propose it to you,  so
you can get funding.
+
you can get funding.
===Motor COntroller===
+
 
 +
====Motor COntroller====
  
  
Line 288: Line 382:
 
Tel. 208.475.4670 | Email jbrickner@olympus-controls.com
 
Tel. 208.475.4670 | Email jbrickner@olympus-controls.com
  
===Torque===
+
====Torque====
  
 
The MRI rotary Unions require 2 in-oz of torque each
 
The MRI rotary Unions require 2 in-oz of torque each
Line 332: Line 426:
 
<math>t = \sqrt{\frac{2 \omega_f}{\alpha}} =\sqrt{\frac{2 50 8 2 *\pi}{87}} = 4.2</math> seconds
 
<math>t = \sqrt{\frac{2 \omega_f}{\alpha}} =\sqrt{\frac{2 50 8 2 *\pi}{87}} = 4.2</math> seconds
  
==Rotary coupler/Union==
+
===Rotary coupler/Union===
  
===ORNL rotating tungsten target===
+
====ORNL rotating tungsten target====
  
 
Full Name: Thomas J. McManamy
 
Full Name: Thomas J. McManamy
Line 352: Line 446:
 
http://www.ornl.gov/info/reporter/no116/nov09_dw.htm#revolution
 
http://www.ornl.gov/info/reporter/no116/nov09_dw.htm#revolution
  
===DSTI===
+
====DSTI====
  
 
http://www.dsti.com/products/?gclid=CPWEvP6ogagCFRs5gwod6SSXtA
 
http://www.dsti.com/products/?gclid=CPWEvP6ogagCFRs5gwod6SSXtA
Line 383: Line 477:
 
Place order for 2 with Michel @ 763-404-8024
 
Place order for 2 with Michel @ 763-404-8024
  
===gat===
+
====gat====
  
 
The guy from Empiremagnetics says that the ferofluid used in the unions below becomes stiff at low temperatures causes too much load on the motors.
 
The guy from Empiremagnetics says that the ferofluid used in the unions below becomes stiff at low temperatures causes too much load on the motors.
Line 394: Line 488:
 
http://www.rotarysystems.com/?gclid=CID4r6z22acCFQM6gwodoQVQ9w
 
http://www.rotarysystems.com/?gclid=CID4r6z22acCFQM6gwodoQVQ9w
 
     http://rotarysystems.com/series-006
 
     http://rotarysystems.com/series-006
 +
 +
===Motor Controller===
 +
 +
http://www.centent.com/
  
 
=Target specifications=
 
=Target specifications=
Line 399: Line 497:
 
The U42 motor has a 4.2 inch diameter.  With a 2" Pb brick for shielding this would put the target radiu to at least (2.1 + 2 + 1) 5.1 inches.
 
The U42 motor has a 4.2 inch diameter.  With a 2" Pb brick for shielding this would put the target radiu to at least (2.1 + 2 + 1) 5.1 inches.
  
== Moment of Inertia==
+
=== Moment of Inertia===
  
 
<math>I_{Disk} = \frac{1}{2} MR^2</math>
 
<math>I_{Disk} = \frac{1}{2} MR^2</math>
Line 405: Line 503:
 
<math>I_{Hoop} = \frac{1}{2} M(R_1^2 +R_2^2)</math>
 
<math>I_{Hoop} = \frac{1}{2} M(R_1^2 +R_2^2)</math>
  
==Torque==
 
  
==Rotational Speed==
+
R= 32 cm = 12.6 inches.
===Mechanical design===
+
 
 +
===Torque===
 +
 
 +
===Rotational Speed===
 +
====Mechanical design====
  
 
An Aluminum disk will be machined to have several Tungsten targets attached.
 
An Aluminum disk will be machined to have several Tungsten targets attached.
Line 426: Line 527:
 
The HRRL easily runs at 300 Hz.  For a target with 20 foils you would run the motor at 300/40 = 7.5 Hz.
 
The HRRL easily runs at 300 Hz.  For a target with 20 foils you would run the motor at 300/40 = 7.5 Hz.
  
===Heat load===
+
 
 +
 
 +
 
 +
 
 +
 
 +
====Heat load====
 
You will need at least 2 holes in the Tungsten disk which you can use as an empty target. The Max pulse rate of the Linac is 1 kHz.  So a 500 Hz motor would be the Max speed needed if you have 2 Windows.
 
You will need at least 2 holes in the Tungsten disk which you can use as an empty target. The Max pulse rate of the Linac is 1 kHz.  So a 500 Hz motor would be the Max speed needed if you have 2 Windows.
  
Line 473: Line 579:
 
:<math>\kappa \equiv</math> Heat Conductivity
 
:<math>\kappa \equiv</math> Heat Conductivity
  
=Q=
+
 
 +
==Sadiq's Calculation ==
 +
 
 +
Moment of inertia of a cylinder rotating in with z axis:
 +
 
 +
<math> I = \frac{m r^2}{2} =  \frac{\rho \times V r^2}{2} = \frac{\rho \times \pi r^2 h \times r^2}{2} = \frac{\rho \pi r^4 h}{2} </math>
 +
 
 +
<math>\alpha = \frac{d w}{dt} = \frac{d^2\theta}{dt^2} = \frac{\tau}{I} </math>
 +
 
 +
<math> w = \frac{\tau}{I}t + w_0  </math>
 +
 
 +
<math> \theta = \frac{1}{2} \frac{\tau}{I} t^2 + w_0 t + \theta_0  </math>
 +
 
 +
Angular change due to acceleration is:
 +
 
 +
<math> \Delta \theta = \frac{1}{2} \frac{\tau}{I} t^2 + w_0 t + \theta_0  - ( w_0 t + \theta_0) = \frac{1}{2} \frac{\tau}{I} t^2 </math>
 +
 
 +
Position change at some distance R from the center is
 +
 
 +
<math> \Delta l = \Delta \theta R = \frac{1}{2} \frac{\tau}{I} t^2 R</math>
 +
 
 +
<math> \Delta l = \frac{1}{2} \frac{\tau}{I} t^2 R</math>
 +
 
 +
Assume we just have one disk, and we are looking for position change at the radius, r=R. We are also looking at the the position change after one revolution, t = T.
 +
 
 +
<math> \Delta l = \frac{1}{2} \frac{\tau}{\frac{\rho \pi r^4 h}{2}} T^2 r  = \frac{\tau}{\rho \pi r^3 h} \frac{1}{f^2}  </math>
 +
 
 +
<math> f^2 r^3 = \frac{\tau}{\rho \pi  h} \frac{1}{\Delta l }  </math>
 +
 
 +
or   
 +
 
 +
<math>f^2 r^3 \Delta l = \frac{\tau}{\rho \pi  h}  </math>
 +
 
 +
=== Rough Estimation ===
 +
 
 +
100 oz-in = 0.706154 N*m
 +
 
 +
<math> \tau = 400~oz-in = 2.82462~N*m </math>
 +
 
 +
<math> \rho_{Al} = 2.7 ~g~ cm^{-3} = 2.7 \times 10^3 ~kg~ m^{-3}</math>
 +
 
 +
We choose:
 +
 
 +
<math> h = 1~inch = 0.0254 ~m</math>
 +
 
 +
 
 +
<math> \Delta l = \frac{1}{4}~inch = 0.00635 ~m</math>
 +
 
 +
<math> f^2 r^3 = \frac{2.82462~N*m}{(2.7 \times 10^3 ~kg~ m^{-3} )\times 3.14 \times (0.0254 ~m)}  \times  \frac{1}{0.00635 ~m } = 2.0656616 </math>
 +
 
 +
<math> f^2 r^3  = 2.0656616 </math>
 +
 
 +
 
 +
<math>  r^3  = \frac{2}{f^2} </math>
 +
 
 +
<math>  r  = ( \frac{2}{f^2} ) ^ {1/3}</math>
 +
 
 +
Which means: If out motor has a torque of <math> 400~oz-in </math>, and rotating a 1 inch thick cylindrical aluminium  plate, to move a point outer edge of the plate, forward or backward, 1/4 inch in next revolution, the radius and frequency of the plate should satisfy:
 +
 
 +
<math>  r^3  = \frac{2}{f^2} </math>
 +
 
 +
 
 +
{| border="1"  |cellpadding="20" cellspacing="0
 +
|-
 +
|r (cm) || r (inch)  || Circumference (in)  ||  #tar (Number of 1-inch-targets can be mounted on the disk) || Rep rate (Hz) ||
 +
|-
 +
| 43.1  || 17.0  || 106.56  ||  53  ||  5 ||
 +
|-
 +
| 27.1  || 10.7  ||  67.00  ||  33    ||  10  ||
 +
|-
 +
| 17.2  || 6.8  || 42.53    ||  21    ||  20 ||
 +
|-
 +
|  13.0  ||  5.1  || 32.14  ||    16    || 30 ||
 +
|-
 +
|  10.8  ||  4.3  || 26.70  ||  23    || 40 ||
 +
|-
 +
|  9.3  || 3.7  || 22.99  ||  11  || 50  ||
 +
|-
 +
|  8.2  || 3.2  || 20.27  ||  10  || 60 ||
 +
|-
 +
|  7.4  || 2.9  || 18.30    ||  9    || 70 ||
 +
|-
 +
|  6.8  || 2.6  ||  16.81  ||  8  || 80  ||
 +
|-
 +
|  6.27  || 2.5 ||  15.50  ||    7    || 90 ||
 +
|-
 +
|  5.85  || 2.2  ||  14.46  ||    7    ||  100 ||
 +
|-
 +
|  3.68  || 1.45  || 9.10  ||  4    ||  200 ||
 +
|-
 +
|  2.81  || 1.11  ||  6.95  ||    3  || 300 ||
 +
|-
 +
|  2.0  || 0.787  ||  4.94  ||  2    || 500 ||
 +
|-
 +
|  1.25  || 0.492 ||  3.09  ||  1    || 1000 ||
 +
 
 +
|}
 +
 
 +
==Q==
 
  Q: Does the W target has to be in the vacuum?  
 
  Q: Does the W target has to be in the vacuum?  
 
     What if we have it in the air, at the ends of the beam line we have very thin vacuum window?  
 
     What if we have it in the air, at the ends of the beam line we have very thin vacuum window?  
Line 498: Line 702:
  
 
Look for Tungsten disks to attach to brushless motor and fit into beam pipe
 
Look for Tungsten disks to attach to brushless motor and fit into beam pipe
[[Positrons]]Go Back
+
 
 +
 
 +
= W Target =
 +
 
 +
W target at [http://www.alfa.com/en/gp100w.pgm?dsstk=13981 Tungsten foil, 1.0mm (0.04in) thick, 99.95% (metals basis)]
 +
 
 +
Pricing and Availability
 +
Size       ($) Price
 +
25x50mm 154.00
 +
50x100mm 258.00
 +
 
 +
 +
 
 +
Target Hub: [[File:W-Tar-Hub.png | 500 px]]
 +
 
 +
 
 +
 
 +
 
 +
 
 +
 
 +
= Chamber =
 +
 
 +
Conceptual design to review: [[Media:hrrl_pos_ch_concept_des_8Aug2012.pdf]]
 +
 
 +
[[File:hrrl_pos_ch_space_1.jpg | 400 px]] [[File:hrrl_pos_ch_space_2.jpg | 400 px]]
 +
 
 +
Chamber's flange to flange distance in Z direction should be 26 inches. The flange down stream the beamline should be as short as possible. 
 +
 
 +
[[File:hrrl_pos_ch_space_3.png | 400 px]]
 +
 
 +
[[File:hrrl_pos_ch_space_4.png | 400 px]]
 +
 
 +
[[File:hrrl_pos_ch_space_5.png | 400 px]]
 +
 
 +
 
 +
== Rotating target system length in Z ==
 +
 
 +
The end to end distance of rotating target system with 2 elbows at two ends measured by Dr. Forest and Sadiq
 +
 
 +
Dr. Forest: 21.5 inches.
 +
 
 +
Sadiq: <math>21\frac{1}{8}~21\frac{3}{8}</math> inches.
 +
 
 +
 
 +
 
 +
== Chamber Target system ==
 +
 
 +
[[File:HRRL_Cham_T1_sys_1.jpg | 400 px]]
 +
[[File:HRRL_Cham_T1_sys_2.jpg | 400 px]]
 +
 
 +
Go Back [[Positrons]]

Latest revision as of 22:26, 12 October 2012

PositronTargetWorkByChrissJackson

Target Construction

Current beam line distances for target to be inserted into

Hrrl e+ Target area Space.png

Motor

HRRL Beam Rot Tar Sys Mot1.png

Empire Magnetics Model U42

Wiring Diagram
Media:U-42EmpireMagneticsMotorWiringDiag.pdf

Motor test video 1

test video 2

test video 3

test video 4

test video 5

Motor Controller

Power supply

Power Supply STP-PWR-4810 Power supply for stepping systems, dual output with 48 VDC @ 10A (at full load) unregulated and 5 VDC at 0.5A regulated.

STR8

STR8.png

STR8 Manuals:

Media:STR_Hardware_Manual.pdf

Media:STR_Quick_Setup_Guide.pdf

Datasheet:

Media:STR_Brochure_925-0002_RevC.pdf

Design

Documents

File:BRACKET TUBE END SUPPORT 1.pdf

File:CAP FITTING.pdf

File:CONE TAPER LOCK.PDF

File:COOLING COOL A HELICAL.PDF

File:FERRULE 1.PDF

File:FITTING ASSY 1 ISO CUT AWAY 2.PDF

File:FITTING MAIN BODY.PDF

File:HOSE CLAMP.PDF

File:HUB PEMSERT ASSY.PDF

File:HUB TAPER LOCK.PDF

File:S VSRH U42 RTD 110726A SYSTEM LAYOUT.pdf

File:S VSRH U42 RTD HS.PDF


45 degree angle

The Tungsten target should make a 45 degree angle with the beam.

make the motor so it can be rotated.


Beam Heat Load

Accelerator Settings
beam energy 10 MeV
Rep Rate: 300 Hz
I_peak: 200 mA/pulse
pulse width: 0.1 [math]\mu[/math]s (100 ns)
Vacuum: [math]10^{-8}[/math] Torr
[math]200 \frac{\mbox{mA}}{\mbox{pulse}} \times 300 \frac{\mbox{pulses}}{\mbox{sec}} \times 0.1 \mu \mbox{s}= 60 \mu A[/math]

Time on for one second is 30 us. and Time off is 0.999999 s The average current 0.999999 * 0 + 0.000001*300*200mA = 60[math]\mu[/math]A.

P = (10 MeV) [math]\times[/math] (60 [math]\mu[/math]A) = 600 Watts.

Target Chamber design

Latest Design From empire and Sadiq's measurement of the available space


EmpMagHRRLPositronTargetChamberDrw 9-20-11.png HRRLPositronTargetSpace 10-5-11.png HRRLPositronTargetCoupler 10-5-11.png HRRLPositronTargetHub 10-5-11.png
Target motor Design Available beam line space Motor axle coupling to rotary union Hub and spline to attache targets


Dimensions are in inches

HRRLPositronTargetChamber 4-20-11.png

There is an 18" space in Z for the target chamber. If you want to rotate a disk on the 5" wide motor you will need at least a a 10" x 10" area.

So we could try as a first design a chamber which is 18" x 15" x 15". We need the following

  • 2 beam flanges flush with the walls of the chamber.
  • 2 flanges to allow access for hands to work on the target motor inside. It should able to fit hands through.
  • a flange on top which will allow a 10" diameter target disk to come out.
  • a flange on the bottom for the ion pump.


July Design From empire

EmpMagHRRLPositronTargetChamberDrw 7-25-11.png

EmpMagHRRLPositronTargetChamberPict 7-25-11.png EmpMagStatorCoolLines 7-26-11.png
Rotary Union overlayed on conceptual drawing. Conceptual drawing of stator cooling lines. We will need separate connection to them on the vacuum chamber.

Gate Valve - Target distance

The distance from the front of the gate valve to the most beam upstream part of the target chamber is

88.43 cm

The gate valve closes in 0.7 sec.


So water would need to travel at a speed of 88.43 cm/0.7 sec = 1.26 m/sec

Properties of Tungsten

  • Melting Point = 3695 K.
  • Heat Capacity = [math](25~ ^{o}C)~ 24.27 ~ J ~ mol^{-1} ~ K^{-1}[/math]


  • Heat loss due to radiation: ( \sigma T^4)

Tungsten Temperature as a function of heat load

  • IAC beamline pressure = [math]10^{-8} [/math] Torr
  • The Tungsten heats up when an MeV energy electron impinges its surface. The imperfect vacuum inside the beam pipe does allow some radiative cooling.
  • Conduction and Radiation

Calculating Radiators Equilibrium Temperature

1.Calculating number of particles per second

We have electron beam of:

Frequency: f=1000Hz

Peak current: I=10~mAmp=0.01 Amp

Pulse width: [math] \Delta t= 50~ns=5 \times10^{-8}[/math] seconds

So, how many electrons we have in each second?

By Q=It, we have


                           [math] N \times e=f \times I \times \Delta t [/math]


Where N is the total electron numbers hits target per second, e is electron charge and f, I and ∆t are given above. Number of particle per second is:


                           [math]  N = \frac {f \times I \times \Delta t}{e} [/math]


2.Calculating Energy deposited per second

If we find the energy deposited by each electron and multiply to the total number of electrons in each second, we will find the total energy per second deposited in radiator.

To find energy deposited by each electron, we need to use formula

                              [math] E_{dep~one}={(\frac{dE}{dx})}_{coll}\times t [/math]


Where is [math] E_{dep~one} [/math] is energy deposited by one electron, [math] {(\frac{dE}{dx})}_{coll} [/math] is mean energy loss (also stopping power) by collision of electron and [math] t [/math] is thickness of the radiator.

Actually, energy loss of a electron comes from two parts: 1) the emission of electromagnetic radiation arising from scattering in the electric field of a nucleus (bremsstrahlung); 2) Collisional energy loss when passing through matter. Bremsstrahlung will not contribute to the temperature, because it is radiation.

Stopping power can be found from nuclear data tables [math] (dE/dx)_{ave} [/math] and thickness is 0.001 times of radiation length. From Particle Data group we got radiation length and average total stopping powers around 15MeV for electrons in these materials from National Institute of Standards and Technology: Tungsten Stopping Power.

Table of Radiation Lengths

Note:These data is from Particle Data group,Link: [1].

Elements Radiation Lengths [math] (g/cm^{2} )[/math]
W 6.76


Table of energy calculations

For the thickness of 0.001 Radiation Length (0.0001RL) of radiators. Note: [math](dE/dx)_{coll}[/math] is from National Institute of Standards and Technology. Link: [[2]])

Elements [math](dE/dx)_{coll} (MeV \; cm^2/g)[/math] [math] t~( g~cm^{-2}[/math]) [math]E_{(dep~one)}[/math] (MeV) [math]E_{dep/s}[/math] (MeV/s) [math]E_{dep/s}[/math] (J/s)
W 1.247 0.00676 0.00842972 [math]2.63*10^{10}[/math] [math]4.21*10^{-3}[/math]

In above table,we took the total numbers of electrons per second and multiply it to Energy deposited by one electron,get total energy deposited per second (which is power).

                                         [math]P_{dep}= E_{dep}/s = ( E_{(dep~by~one)})\times(Number~of~electrons~per~second)[/math]

3.Calculating equilibrium temperature using Stefan–Boltzmann law

If we assume that there is no energy conduction and total energy is just radiated from two surfaces of the radiators which are as big as beam spot,in our case beam spot is 2mm in diameter. According to Stefan–Boltzmann law, this total power radiated will be

                                           [math] P_{rad} =  A \sigma T^{4}  [/math]

Where T is radiating temperature P is the radiating power, A is surface area that beam incident and σ is Stefan–Boltzmann constant or Stefan's constant. To reach equilibrium temperature, Power deposited in and power radiated should be. So

                                           [math]  P_{dep}=P_{rad}  [/math]

so

                                        [math] T = [  \frac{P_{dep}}{A\sigma} ]^{1/4} = [  \frac{N*E_{(dep~one)}}{A\sigma} ]^{1/4} [/math]



Vendors

MDC Target Chamber

Target chamber: MDC vacuum products can send a prefab one you just need to weld up.

John Brooks

jbrooks@mdcvacuum.com


1-800-443-8817

or

510-265-3569

File:TargetChamberDesign 1.0.pdf

Tom Bogden (John's boss)


MDC does not have a fast closing gate valve. Model GV1500 closes in 0.7 seconds and costs $1600. One that closes in 10 msec costs about $10k

Tungsten Disks

Dimensions are in cm

HRRL PosTargetDesign 4-20-11.png

http://www.alibaba.com/product-gs/346924116/Tungsten_Disk_With_Screw.html


http://www.zlxtech.com.cn/products.asp?productcode=7401000404

http://www.cleveland-tungsten.com/


If the motor has a radius of 2.5" and I want to shield the motor from the beam using 2" of Pb and the beam is about 1" in diameter then I want a Tungsten disk that is

5.21" in radius = 13.25 cm in radius ~ 30 cm in diameter

Then density of Tungsten is

19.25 g/cm^3


19.25 g/cm^3 \times \pi (30 cm)^2 = 54,428 g/cm

= 8.7 kg if it is 0.16 cm thick

The moment of inertia for a disk about its center is MR^2/2

So I = 8.7kg \times (0.3 m)^2/2 = 0.4 kg m^2

I should look into a ring of tungsten attached to a less dense material.

VX-U42 torque is about 50 in-lbs = 5.65 N m

Max acceleration would be

[math]\alpha = \frac{5.65 N m}{0.4 kg m^2} = 14.4 rad/sec \times \frac{1}{2 \pi} = 2.3 cycles/sec[/math]

Brushless Motor

Motor wiring diagram

Media:U-42EmpireMagneticsMotorWiringDiag.pdf


Rick Halstead

5830 Commerce Blvd

Rohnert Park, CA 94928

Phone: 707-584-2801

Fax: 707-584-3418

rick@empiremagnetics.com:

The VX grade motors, with dry lubes have been used in deep space (Wake Shield Module) where I'm told they were trying to get 10^-12 torr.


We need 10^{-8 }Torr

Vacuum lab grade motor U42.

http://www.empiremagnetics.com/prod_vac/prod_vac_vx_stepper_frame42.htm


Tony: Some of the couplings I had in mind: http://www.sdp-si.com/estore/CoverPg/Couplings.htm

http://www.servometer.com/products/couplings/

I'm thinking the coupler with adaptation of a compression seal. http://www.jaecofs.com/stainless-steel-compression-fittings.html

The challenge will be to get them to make a version that can be sealed at each end, technically it is feasible, it's an issue of engineering resource to chase them down, get a quote then propose it to you, so you can get funding.

Motor COntroller

Jason Brickner Olympus Controls Tel. 208.475.4670 | Email jbrickner@olympus-controls.com

Torque

The MRI rotary Unions require 2 in-oz of torque each

The U42 has a minimum static torque of 375 in-oz (1 Nm/8.851 oz-in) = 42.4 Nm

The Momentum of inertia of a thin disk about its axial axis is

[math]MR^2/2[/math]

Moment of Inertia of a ring:

[math]MR^2[/math]

The target will be a disk of Aluminum with an outer ring of tungsten.

[math]I_{\mbox{Al disk}} =M_{\mbox{Al}} R^2[/math]

[math]M_{\mbox{Al}}= \rho \times V = 2.7 g/cm^3 (0.2 cm) \times \pi ( 9 in 2.54 cm/in)^2 =2.7 g/cm^3 0.2 cm \pi 523 cm^2 = 886 g[/math]

[math]I_{\mbox{Al disk}} =886 g \times 523 cm^2 = 463423 g cm^2 \times (1 oz/28 g) (1 in/2.54 cm) (1in/2.54 cm) = 2565 oz-in^2 [/math]

[math]Torque = 42.4 Nm = I \alpha[/math]

\alpha = 42.4 Nm/(0.04 kg m^2))=1060 rad/sec^2

I_{\mbox{W}} = MR^2 =


[math]M_{\mbox{W ring}} = 19.25 g/cm^3 \times \pi ((30 cm)^2 - (28.5 cm)^2) = 5.3 kg = 11.7 lbs[/math]

[math]I = 5.3 kg \times 29 cm^2 = 0.4457 kg m^2[/math]

[math]I_{tot} = I_{\mbox{Al disk}} + I_{\mbox{W}} = (0.04 + 0.4457) kg m^2[/math]

[math]\alpha = 42.4 Nm/(0.49 kg m^2) = 87 rad/s^2[/math]

How much time to accelerate to 50 Hz = [math]50 *2 *\pi[/math] rad/sec?

[math]\omega_f = \alpha t^2/2[/math]

[math]t = \sqrt{\frac{2 \omega_f}{\alpha}} =\sqrt{\frac{2 50 8 2 *\pi}{87}} = 4.2[/math] seconds

Rotary coupler/Union

ORNL rotating tungsten target

Full Name: Thomas J. McManamy

Email Address: mcmanamytj@ornl.gov

Phone Number: 865-576-0039

Fax Number: 865-241-6909

Postal Address: OAK RIDGE NATIONAL LABORATORY

PO BOX 2008 MS6476

OAK RIDGE TN 37831-6476

http://www.ornl.gov/info/reporter/no116/nov09_dw.htm#revolution

DSTI

http://www.dsti.com/products/?gclid=CPWEvP6ogagCFRs5gwod6SSXtA

Brett Villella brett.villella@dsti.com

Dynamic Sealing Technologies, Inc.

13829 Jay Street NW

Andover, MN 55304

Direct: 763-404-8021

Main: 763-786-3758

Fax: 763-786-9674

Web: www.dsti.com

Model: SPS-5510-R.A , a single pass rotary union, the input connector is 3/4" diameter as shown in the drawing below.

The minimum torque needed to rotate base on zero pressure is 4 in-lbs.

File:SinglePassRotaryUnionDSTi v1.pdf

The target chamber design should be able to accommodate a 4" = 3.14+ 1" length in order to accept a rotary union which works at liquid nitrogen temperatures.  The above single pass rotary union is good to -25F according to the company.

Place order for 2 with Michel @ 763-404-8024

gat

The guy from Empiremagnetics says that the ferofluid used in the unions below becomes stiff at low temperatures causes too much load on the motors.


http://www.gat-mbh.de/index.php?page=rotovac-en&group=produkte-en:rotating_unions-en

http://www.tengxuan.net/old/product.asp?Catalog=8

http://www.rotarysystems.com/?gclid=CID4r6z22acCFQM6gwodoQVQ9w

   http://rotarysystems.com/series-006

Motor Controller

http://www.centent.com/

Target specifications

The U42 motor has a 4.2 inch diameter. With a 2" Pb brick for shielding this would put the target radiu to at least (2.1 + 2 + 1) 5.1 inches.

Moment of Inertia

[math]I_{Disk} = \frac{1}{2} MR^2[/math]

[math]I_{Hoop} = \frac{1}{2} M(R_1^2 +R_2^2)[/math]


R= 32 cm = 12.6 inches.

Torque

Rotational Speed

Mechanical design

An Aluminum disk will be machined to have several Tungsten targets attached.

The disk has a radius of about 5.1 inches. The circumference will be 2 \pi r \approx 45 inches. If the targets are 1" wide with 1" gaps, then you will have about 20 targets.


If you rotate the target at 1 Hz then in one second you can hit 20 targets. This means your rep rate can be 20 Hz.

If you rotate the target at 50 Hz then your rep rate can be 1 kHz.

But since you will have 20 gaps (empty target positions) then you could run at 2 kHz.

So a target rotating 25 Hz can accept a rep rate of 1 kHz.


The HRRL easily runs at 300 Hz. For a target with 20 foils you would run the motor at 300/40 = 7.5 Hz.




Heat load

You will need at least 2 holes in the Tungsten disk which you can use as an empty target. The Max pulse rate of the Linac is 1 kHz. So a 500 Hz motor would be the Max speed needed if you have 2 Windows.


How long can a 1.6 mm thick piece of Tungsten that has an area of 2.5" x 2.5" be in a 600 Watt heat source before melting.

Specific Heat Capacity = [math] 130 \frac{J}{kg K}[/math]

Thermal Conductivity = [math] 173\frac{W}{m K}=100\frac{BTU}{hr ft F}[/math]

The Melting point of Tungsten is 3600 Kelvin.

density = 19.25[math]\frac{g}{cm^3}[/math]

Volume = [math](.16 cm)(2.5 cm)^2 = 1 cm^3[/math]

Mass = [math]1 cm^2 \times 19.25 g/cm^3 = 19.25 g :\lt math\gt Q = C_m m \Delta T = 130 \frac{J}{kg K} \times 0.967 kg \times (3600-300 K) = 414843 J = 600 J/s *t [/math] Watt = J/s

[math]\Rightarrow t= 691 seconds.[/math]

If Zinc

C_m = 0.39 J/g/K Density = 7.13 g/cm^3 \Right arrow M = 7.13 \times 50.3 = 358 g, Melting point 693 K
Q = 0.39 \times 0.358 \times 393 = 55 Joules = 10^3 Watts * t \Rightarrow t = 0.055 s \Rightarrow 18 Hz.

Now You need to calculate how quickly water can absorb heat

Water properties
C_m = 4.12 J/g/K , Density = 1 g/cm^3 assuming aflow rate of 1 liter/sec \Rightarrow mass = 1 g, Boiling point water = 373.15


Tungsten's specific heat capacity is about 30 times larger than water. So for the same mass and power input water's temperature will change a factor of 30 more than tungsten.



In 1 second Tungsten's temperature change will be

\frac{600 J}{130 \times 0.967} = 5K


Copper coils which have water flowing through them are soldered to the Tungsten. The water is a heat sink transferring heat from the Tungsten to the water.

Heat transfer by conduction
[math]\frac{Q}{t} = \frac{\kappa A \Delta T}{d}[/math]
[math]\kappa \equiv[/math] Heat Conductivity


Sadiq's Calculation

Moment of inertia of a cylinder rotating in with z axis:

[math] I = \frac{m r^2}{2} = \frac{\rho \times V r^2}{2} = \frac{\rho \times \pi r^2 h \times r^2}{2} = \frac{\rho \pi r^4 h}{2} [/math]

[math]\alpha = \frac{d w}{dt} = \frac{d^2\theta}{dt^2} = \frac{\tau}{I} [/math]

[math] w = \frac{\tau}{I}t + w_0 [/math]

[math] \theta = \frac{1}{2} \frac{\tau}{I} t^2 + w_0 t + \theta_0 [/math]

Angular change due to acceleration is:

[math] \Delta \theta = \frac{1}{2} \frac{\tau}{I} t^2 + w_0 t + \theta_0 - ( w_0 t + \theta_0) = \frac{1}{2} \frac{\tau}{I} t^2 [/math]

Position change at some distance R from the center is

[math] \Delta l = \Delta \theta R = \frac{1}{2} \frac{\tau}{I} t^2 R[/math]

[math] \Delta l = \frac{1}{2} \frac{\tau}{I} t^2 R[/math]

Assume we just have one disk, and we are looking for position change at the radius, r=R. We are also looking at the the position change after one revolution, t = T.

[math] \Delta l = \frac{1}{2} \frac{\tau}{\frac{\rho \pi r^4 h}{2}} T^2 r = \frac{\tau}{\rho \pi r^3 h} \frac{1}{f^2} [/math]

[math] f^2 r^3 = \frac{\tau}{\rho \pi h} \frac{1}{\Delta l } [/math]

or

[math]f^2 r^3 \Delta l = \frac{\tau}{\rho \pi h} [/math]

Rough Estimation

100 oz-in = 0.706154 N*m

[math] \tau = 400~oz-in = 2.82462~N*m [/math]

[math] \rho_{Al} = 2.7 ~g~ cm^{-3} = 2.7 \times 10^3 ~kg~ m^{-3}[/math]

We choose:

[math] h = 1~inch = 0.0254 ~m[/math]


[math] \Delta l = \frac{1}{4}~inch = 0.00635 ~m[/math]

[math] f^2 r^3 = \frac{2.82462~N*m}{(2.7 \times 10^3 ~kg~ m^{-3} )\times 3.14 \times (0.0254 ~m)} \times \frac{1}{0.00635 ~m } = 2.0656616 [/math]

[math] f^2 r^3 = 2.0656616 [/math]


[math] r^3 = \frac{2}{f^2} [/math]

[math] r = ( \frac{2}{f^2} ) ^ {1/3}[/math]

Which means: If out motor has a torque of [math] 400~oz-in [/math], and rotating a 1 inch thick cylindrical aluminium plate, to move a point outer edge of the plate, forward or backward, 1/4 inch in next revolution, the radius and frequency of the plate should satisfy:

[math] r^3 = \frac{2}{f^2} [/math]


r (cm) r (inch) Circumference (in) #tar (Number of 1-inch-targets can be mounted on the disk) Rep rate (Hz)
43.1 17.0 106.56 53 5
27.1 10.7 67.00 33 10
17.2 6.8 42.53 21 20
13.0 5.1 32.14 16 30
10.8 4.3 26.70 23 40
9.3 3.7 22.99 11 50
8.2 3.2 20.27 10 60
7.4 2.9 18.30 9 70
6.8 2.6 16.81 8 80
6.27 2.5 15.50 7 90
5.85 2.2 14.46 7 100
3.68 1.45 9.10 4 200
2.81 1.11 6.95 3 300
2.0 0.787 4.94 2 500
1.25 0.492 3.09 1 1000

Q

Q: Does the W target has to be in the vacuum? 
   What if we have it in the air, at the ends of the beam line we have very thin vacuum window? 
   In photofission experiment we had 1 mil vacuum window. under 
   15 MeV e- beam, only 1/1000 electron will interact with the window, produce bremsstrahlung photon.
Q: Can we make positron target that is inner part of the vacuum box, then we rotate all the box. Heat will be transfered to box, 
   box can cooled by water from outside. 
   May be box does not have to rotation movement? I can do other moments like up-down and right-left.

  I think we can make a Tungsten target as a part of the beam line. That means outer part Tungsten target will be beam pine. 
Then we can use water cooling to cool our Tungsten target from outside. 
Before we had all the electrons hitting Faraday Cup, which did not melt the copper even when there was not cooling water 
circling around FC. 
Tungsten has higher melting point, plus we run cooling water around Tungsten target, then Tungsten shouldn't melt.


The first version of a positron converter target will be designed to distribute the heat load by rotating the tungsten target.


Calculate for 1 mm and 2 mm thick Tungsten


Look for Tungsten disks to attach to brushless motor and fit into beam pipe


W Target

W target at Tungsten foil, 1.0mm (0.04in) thick, 99.95% (metals basis)

Pricing and Availability
Size 	      ($) Price 		
25x50mm 	154.00 			
50x100mm 	258.00 	


Target Hub: W-Tar-Hub.png




Chamber

Conceptual design to review: Media:hrrl_pos_ch_concept_des_8Aug2012.pdf

Hrrl pos ch space 1.jpg Hrrl pos ch space 2.jpg

Chamber's flange to flange distance in Z direction should be 26 inches. The flange down stream the beamline should be as short as possible.

Hrrl pos ch space 3.png

Hrrl pos ch space 4.png

Hrrl pos ch space 5.png


Rotating target system length in Z

The end to end distance of rotating target system with 2 elbows at two ends measured by Dr. Forest and Sadiq

Dr. Forest: 21.5 inches.

Sadiq: [math]21\frac{1}{8}~21\frac{3}{8}[/math] inches.


Chamber Target system

HRRL Cham T1 sys 1.jpg HRRL Cham T1 sys 2.jpg

Go Back Positrons