CLAS12 R1 S1 QA

From New IAC Wiki
Jump to navigation Jump to search

HV burn in

Begin burn in after at least 3 volume changes.


File:High Voltage Region 1 Sector 1 data.xls


Step 1: Set Voltage to 50 volts on all channels. Probe HVB to be sure that all sense, field, and guard wires have a voltage. (You should set current threshold to 10 microAmps on the HV supply)

Step 2: While monitoring the current, ramp the HV to the following

G:F:S= 525,-700,700

Step 3: Begin to take data recording the time and sense wire current as you ramp up the sense wire HV to 1400 volts while restricting the current draw to less than 10 micraAmps.


keep current under 10 micro amps while moving sense voltage up to 1400

Measured Sense wire output

CLAS12_R1_S1_QA_wireOut


Sense Wire Scope pictures on DAQ machine

Cosmic Runs

CLAS12R1_CosmicTestStand

3811

Cosmic rays were used to measure drift chamber time spectra with respect to scintillators placed above and below the drift chambers (more details are at the wiki location CLAS12R1_CosmicTestStand)


CLAS6 DCrawTDCspectrum.gif R3811 TDC51 Time.png R3831 3833TDC51 TimeL1W9.png JLabR1Chambr4.png
Fig 23 from "The CLAS drift chamber system", M. Mestayer, et. al., NIM A, Volume 449, Issues 1–2, 11 July 2000, Pages 81–111 cosmic run from 1/10 - 1/14. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width). Cosmics runs with lower discriminator thresholds Chamber 4 at JLab

DChitDisplay 3831.png

R3811_TDCspectra

3833

R3833_TDCspectra

R3833_Efficiency1

3834

R3834_TDCspectra

Cosmic measurements

CLAS6 Drift Chamber NIM paper

File:NIM A 449 2000 pg81.pdf


Run # Date Description
3806 1/10/13 3 hour cosmic run, 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width)
3809 1/10/13 cosmic run on 1/10. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width).
3810 1/10/13 cosmic run from 1/10 - 1/14. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width). Scintillator paddle F1/F2 on table above Sector 1, paddle I1/I2 below.
3811 1/10/13
3831 2/1/13 Changed disciminator from 80 mV to 60 mV, We improved the window, installed HV & STB boards, purged and started taking cosmic data again, DC is sandwhiched between 2 scints with PMTs aligned (PMT on only one end of Scint is turned on)
3833 2/4/13 Changed disciminator from 60 mV to 30 mV
3834 2/11/13 Changed disciminator from 30 mV to 60 mV
3835 2/19/13 Changed disciminator from 60 mV to 20 mV

Using ADB crate

TDC-CH# WIRE
104 PMT I2
106 PMT F2
107 PMT F1
00 U1 L2W1
01 U2 L4W1
02 U3 L6W1
03 U4 L1W1
04 U5 L3W1
05 U6 L5W1
06 U7 L2W2
07 U8 L4W2
08 U9 L6W2
09 U10 L1W2
10 U11 L3W2
11 U12 L5W3
12 U13 L2W3
13 U14 L4W3
14 U15 L6W3
15 U16 L1W3
16 U17 L3W3
17 U18 L5W3
18? U19 L2W4
19 U20 L4W4
20 U21 L6W4
21 U22 L1W4
22 U23 L3W4
23 U24 L5W4
24 U25 L2W5
25 U26 L4W5
26 U27 L6W5
27 U28 L1W5
28 U29 L3W5
29 U30 L5W5
30 U31 L2W6
31 U32 L4W6
32 U33 L6W6
33 U34 L1W6
34 U35 L3W6
35 U36 L5W6
36 U37 L2W7
37 U38 L4W7
38 U39 L6W7
39 U40 L1W7
40 U41 L3W7
41 U42 L5W7
42 U43 L2W8
43 U44 L4W8
44 U45 L6W8
45 U46 L1W8
46 U47 L3W8
47 U48 L5W8
48 U49 L2W9
49 U50 L4W9
50 U51 L6W9
51 U52 L1W9
52 U53 L3W9
53 U54 L5W9
54 U55 L2W10
55 U56 L4W10
56 U57 L6W10
57 U58 L1W10
58 U59 L3W10
59 U60 L5W10
60 U61 L2W11
61 U62 L4W11
62 U63 L6W11
63 U64 L1W11
64 U65 L3W11
65 U66 L5W11
66 U67 L2W12
67 U68 L4W12
68 U69 L6W12
69 U70 L1W12
70 U71 L3W12
71 U72 L5W12
72 U73 L2W13
73 U74 L4W13
74 U75 L6W13
75 U76 L1W13
76 U77 L3W13
77 U78 L5W13
78 U79 L2W14
79 U80 L4W14
80 U81 L6W14
81 U82 L1W14
82 U83 L3W14
83 U84 L5W14
84 U85 L2W15
85 U86 L4W15
86 U87 L6W15
87 U88 L1W15
88 U89 L3W15
89 U90 L5W15
90 U91 L2W16
91 U92 L4W16
92 U93 L6W16
93 U94 L1W16
94 U95 L3W16
95 U96 L5W16

Runlist

Run # Date Description
4008 4/11/13 set ADB threshold to 100 , installed all 6 STB connectors, key was on the left as you face the ADC crate. Two top PMTs and one bottom PMT were in coincidence. The rate was about 0.5 Hz. at 9:41 on 4/12/13 I observed no voltage coming out of the discriminator monitor, the fuses were NOT blown. Hits seemed to disappear in the data. I recycled the ADB crate power and saw 100 mV on the discriminator monitor. Start a new run 40009
4009 4/12/13 ADC threshold at 100 mV
4014 4/16/13 Removed cable from J10 connector on ADB crate and becan a cosmic run, the ROC & EB1 segfaulted after 57702 events
4082 4/17/13 first run with fully installed ADC crate & known map; ROC crashed after 5522 event around 20:53
4099 4/17/13 ROC & EB crash after 4702 events, restarted all processes prior to taking this data
4127 4/24/13 100 mv Threshold, S:F:G=1500:-750:550 ROC crashed because there was not enough memory for all the data, increased memory in the readoutlist R4127Histos
4128 4/24/13 run ended on 4/29 at 10:43,100 mv Threshold, S:F:G=1500:-750:550 re-centered scintillator based on occupancy plot from 4127, the event rate dropped after 2 hrs (event 5000) , TDC chan 32 -> 63 dropped out between event number 5000 and 360000, why did they start working?
4129 4/29/13 100 mv Threshold, S:F:G=1500:-750:550 , lost hits after 50000 events
4130 4/30/13 100 mv Threshold, S:F:G=1500:-750:550 , only 3, 16 channel ADB inputs are working (TDC channels 16->31, 64->95)
4131 5/1/13 100 mv Threshold, S:F:G=1500:-750:550 , Moved DC output connectors so the channels centered on the scintillator are on the working ADB inputs (ribbon cable 3 is on ADB input 2, cable 4 is on input 5, and cable 5 is on ADB input 6); Only ADB input 6 shows hits
4132 5/2/13 100 mv Threshold, S:F:G=1500:-750:550 , Moved DC output connectors so ribbon cable 2 is on ADB input 1, cable 5 is on input 4, and cable 6 is on ADB input 6, all others are unplugged
4134 5/3/13 100 mv Threshold, S:F:G=1500:-750:550 , Moved DC output connectors so ribbon cable 2 is on ADB input 3, cable 5 is on input 5, and cable 6 is on ADB input 6, all others are unplugged
4135 5/4/13 100 mv Threshold, S:F:G=1500:-750:550 , replaced preamp power supply, CLAS12_r4136
4136 5/6/13 100 mv Threshold, S:F:G=1500:-750:550 ,


After 500 -> 4000 events

EB error message

-- Got all fragments of go
thread exit for rocdaq1
get_cb_data returned end of file
ROC mask 8 force_end 2
Segmentation fault

ROC error message:

daLogMsg: INFO: Entering User Go
daLogMsg: INFO: active, events so far 0 token 0
Segmentation fault


vmeOpenDefaultWindows() from the Download state on the ROC?

[root@rocdaq1 ~]# coda_roc_rc3 -t ROC -n rocdaq1 MSQL DATABASE = LDS CODA 2.6.1,Name : rocdaq1, Type ROC Id : 0 INFO: Starting up rcClient Thread...Running the cMsg RC client, "rocdaq1"

 connecting to UDL, cMsg:rc://multicast/LDS

Connect is completed! subscribing subject = rocdaq1 type = run/transition/* subscribing subject = rocdaq1 type = session/control/* subscribing subject = rocdaq1 type = coda/info/* >>>>>> rcClient(Info): Got the request to getState SND END1 >>>>>> rcClient(Info): Got the request to getState callbackControl: Do not understand the command: session/control/setSession Start sending statisitics... >>>>>> rcClient(Info): Got the request to getState SND END1 >>>>>> rcClient(Info): Got the request to getState >>>>>> rcClient(Info): Got the request to getState >>>>>> rcClient(Transition): Got the request to configure Current State: configured Start sending statisitics... callbackControl: Do not understand the command: session/control/setSession >>>>>> rcClient(Info): Got the request to getState daLogMsg: INFO: Downloading configuration "r1dc" daLogMsg: INFO: Downloading readout list /root/linuxvme/r1dc/gen_int_list.so daLogMsg: INFO: _gen_int_list__init() routine found daLogMsg: INFO: readout list loaded rolp->daproc = 0 Init - Initializing new rol structures for GEN_USER Init - Done rolp->daproc = 1 daLogMsg: INFO: Readout list compiled Tue Nov 27 19:07:56 MST 2012 Opening A32 Window (opened at [0xb1a57000,0xb1a67000]) Opening A32Blt Window (opened at [0xa7900000,0xb1900000]) Opening A24 Window (opened at [0xa6900000,0xa7900000]) Opening A16 Window (opened at [0xa68f0000,0xa6900000]) jlabgefMapTsi: Tempe Chip Userspace map successful VME Bus Error IRQ Disabled vmeBusCreateLockShm: vmeBus shared memory mutex created Initialized SIS3610 ID 0 at VME (USER) address 0x3800 (0xa68f3800) daLogMsg: INFO: Initializing TDC 1190 daLogMsg: INFO: User Download Executed daLogMsg: INFO: Downloading readout list /root/linuxvme/r1dc/event_list.so daLogMsg: INFO: _event_list__init() routine found daLogMsg: INFO: readout list loaded rolp->daproc = 0 Init - Initializing new rol structures for ROL2 Init - Done rolp->daproc = 1 daLogMsg: INFO: Readout list compiled Thu Oct 4 13:06:37 MDT 2012 daLogMsg: INFO: User Download 2 Executed daLogMsg: INFO: downloaded Buffer pointer at 0xa666e008 Buffer pointer at 0xa646d008 Buffer pointer at 0xa626c008 Buffer pointer at 0xa606b008 dabufp set to 0xa666e414 ERROR got SIGINT [root@rocdaq1 ~]#



CODA2 DP cpmmunication error

daLogMsg: INFO: opening datalink to eb1:daq2.physics.isu.edu
constructor failed : 40839Couldn't open connection to daq2.physics.isu.edu:40839 : Connection refused
open_links returned : bad file identifier ""

Readout Map

Wire PostAmpOut (CH 1-96) TDC Channel
L W
5 1 1 1
3 1 2 2
1 1 3 3
6 1 4 4
4 1 5 5
2 1 6 6
5 2 7 7
3 2 8 8
1 2 9 9
6 2 10 10
4 2 11 11
2 2 12 12
5 3 13 13
3 3 14 14
1 3 15 15
6 3 16 16
4 3 17 17
2 3 18 18
5 4 19 19
3 4 20 20
1 4 21 21
6 4 22 22
4 4 23 23
2 4 24 24
5 5 25 25
3 5 26 26
1 5 27 27
6 5 28 28
4 5 29 29
2 5 30 30
5 6 31 31
3 6 32 32
1 6 33 33
6 6 34 34
4 6 35 35
2 6 36 36
5 7 37 37
3 7 38 38
1 7 39 39
6 7 40 40
4 7 41 41
2 7 42 42
5 8 43 43
3 8 44 44
1 8 45 45
6 8 46 46
4 8 47 47
2 8 48 48
5 9 49 49
3 9 50 50
1 9 51 51
6 9 52 52
4 9 53 53
2 9 54 54
5 10 55 55
3 10 56 56
1 10 57 57
6 10 58 58
4 10 59 59
2 10 60 60
5 11 61 61
3 11 62 62
1 11 63 63
6 11 64 64
4 11 65 65
2 11 66 66
5 12 67 67
3 12 68 68
1 12 69 69
6 12 70 70
4 12 71 71
2 12 72 72
5 13 73 73
3 13 74 74
1 13 75 75
6 13 76 76
4 13 77 77
2 13 78 78
5 14 79 79
3 14 80 80
1 14 81 81
6 14 82 82
4 14 83 83
2 14 84 84
5 15 85 85
3 15 86 86
1 15 87 87
6 15 88 88
4 15 89 89
2 15 90 90
5 16 91 91
3 16 92 92
1 16 93 93
6 16 94 94
4 16 95 95
2 16 96 96

Measurements with source

4/20/12 1hour counts:

SL2 HVB1 Column 18 Row 5

-With source 14459 pulses/1502 sec


4/23/12 SL1 HVB7 column 203 row 4

-With source 50681 pulses/3760 sec.


4/25/12 1 hour counts:

SL2 HVB4 Column 118 row 5

- Without source: 33145 pulses/3610 Sec.

- With source(CS-137):38262 pulses/3600 Sec.

- Without source: 37548 pulses/3715 Sec.

Preamp voltage:5V

Background measurements

HV off 4/5/12 Background counts:

27 pulses/61806 Sec.

SL2 Column 132 row 2

Preamp voltage 6.3V

Discriminator threshold 46mV


Preamp on= 6.3

4/9/12: Back ground count measurements

4531 counts/69564 seconds

2044 counts/24620 seconds


4/10/12 Background counts:

3 pulses/ 74500 sec.

SL1 HVB7 Column 196 Row 2

Preamp voltage 6.3 V

Discriminator threshold 46mV


4/16/12 Background counts:

280 pulses/245850 sec

SL1 HVB7 column 226 row 2

preamp voltage 5V

Discriminator threshold 46mV


4/17/12 Background counts:

6 pulses/62407 sec

SL2 HVB7 column 226 row 8

preamp voltage 5V

discriminator threshold 46mV


4/20/12 Background counts:

63 pulses/ 71724 Sec.

SL1 HVB7 column 226 row 8

Preamp voltage 5V

Discriminator threshold 46mV


4/23/12 Background counts:

41078 pulse/ 245104 sec.

SL1 HVB7 Column 203 Row 4

Preamp voltage 5V

Discriminator threshold 46mV

Cosmic measurements

4/24/12 Cosmic count:

SL1 HVB1 Column 3 Row 10

14534 pulses/11547 sec.

Preamp voltage 5V


4/26/12 Overnight Cosmic pulse count:

SL2 HVB4 Column 118 Row 5

53122 pulses/49793 Sec.

Preamp voltage 5V



CLAS12_R1