Difference between revisions of "CLAS12 R1 S1 QA"
| Line 304: | Line 304: | ||
|- | |- | ||
|4099|| 4/17/13 || ROC & EB crash after 4702 events, restarted all processes prior to taking this data | |4099|| 4/17/13 || ROC & EB crash after 4702 events, restarted all processes prior to taking this data | ||
| + | |- | ||
| + | |4127|| 4/24/13 || ROC crashed because there was not enough memory for all the data, increased memory in the readoutlist [[R4127Histos]] | ||
|- | |- | ||
|} | |} | ||
Revision as of 17:16, 25 April 2013
HV burn in
Begin burn in after at least 3 volume changes.
File:High Voltage Region 1 Sector 1 data.xls
Step 1: Set Voltage to 50 volts on all channels. Probe HVB to be sure that all sense, field, and guard wires have a voltage. (You should set current threshold to 10 microAmps on the HV supply)
Step 2: While monitoring the current, ramp the HV to the following
G:F:S= 525,-700,700
Step 3: Begin to take data recording the time and sense wire current as you ramp up the sense wire HV to 1400 volts while restricting the current draw to less than 10 micraAmps.
keep current under 10 micro amps while moving sense voltage up to 1400
Measured Sense wire output
Sense Wire Scope pictures on DAQ machine
Cosmic Runs
3811
Cosmic rays were used to measure drift chamber time spectra with respect to scintillators placed above and below the drift chambers (more details are at the wiki location CLAS12R1_CosmicTestStand)
 |
 |
 |
|
| Fig 23 from "The CLAS drift chamber system", M. Mestayer, et. al., NIM A, Volume 449, Issues 1–2, 11 July 2000, Pages 81–111 | cosmic run from 1/10 - 1/14. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width). | Cosmics runs with lower discriminator thresholds | Chamber 4 at JLab |
3833
3834
Cosmic measurements
| Run # | Date | Description |
| 3806 | 1/10/13 | 3 hour cosmic run, 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width) |
| 3809 | 1/10/13 | cosmic run on 1/10. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width). |
| 3810 | 1/10/13 | cosmic run from 1/10 - 1/14. Signal cable 4 (ch. 48-63). 16 channels with leading edge discriminators (-80 mV, 100 ns pulse width). Scintillator paddle F1/F2 on table above Sector 1, paddle I1/I2 below. |
| 3811 | 1/10/13 | |
| 3831 | 2/1/13 | Changed disciminator from 80 mV to 60 mV, We improved the window, installed HV & STB boards, purged and started taking cosmic data again, DC is sandwhiched between 2 scints with PMTs aligned (PMT on only one end of Scint is turned on) |
| 3833 | 2/4/13 | Changed disciminator from 60 mV to 30 mV |
| 3834 | 2/11/13 | Changed disciminator from 30 mV to 60 mV |
| 3835 | 2/19/13 | Changed disciminator from 60 mV to 20 mV |
Using ADB crate
| TDC-CH# | WIRE | |
| 104 | PMT I2 | |
| 106 | PMT F2 | |
| 107 | PMT F1 | |
| 00 | U1 | L2W1 |
| 01 | U2 | L4W1 |
| 02 | U3 | L6W1 |
| 03 | U4 | L1W1 |
| 04 | U5 | L3W1 |
| 05 | U6 | L5W1 |
| 06 | U7 | L2W2 |
| 07 | U8 | L4W2 |
| 08 | U9 | L6W2 |
| 09 | U10 | L1W2 |
| 10 | U11 | L3W2 |
| 11 | U12 | L5W3 |
| 12 | U13 | L2W3 |
| 13 | U14 | L4W3 |
| 14 | U15 | L6W3 |
| 15 | U16 | L1W3 |
| 16 | U17 | L3W3 |
| 17 | U18 | L5W3 |
| 18? | U19 | L2W4 |
| 19 | U20 | L4W4 |
| 20 | U21 | L6W4 |
| 21 | U22 | L1W4 |
| 22 | U23 | L3W4 |
| 23 | U24 | L5W4 |
| 24 | U25 | L2W5 |
| 25 | U26 | L4W5 |
| 26 | U27 | L6W5 |
| 27 | U28 | L1W5 |
| 28 | U29 | L3W5 |
| 29 | U30 | L5W5 |
| 30 | U31 | L2W6 |
| 31 | U32 | L4W6 |
| 32 | U33 | L6W6 |
| 33 | U34 | L1W6 |
| 34 | U35 | L3W6 |
| 35 | U36 | L5W6 |
| 36 | U37 | L2W7 |
| 37 | U38 | L4W7 |
| 38 | U39 | L6W7 |
| 39 | U40 | L1W7 |
| 40 | U41 | L3W7 |
| 41 | U42 | L5W7 |
| 42 | U43 | L2W8 |
| 43 | U44 | L4W8 |
| 44 | U45 | L6W8 |
| 45 | U46 | L1W8 |
| 46 | U47 | L3W8 |
| 47 | U48 | L5W8 |
| 48 | U49 | L2W9 |
| 49 | U50 | L4W9 |
| 50 | U51 | L6W9 |
| 51 | U52 | L1W9 |
| 52 | U53 | L3W9 |
| 53 | U54 | L5W9 |
| 54 | U55 | L2W10 |
| 55 | U56 | L4W10 |
| 56 | U57 | L6W10 |
| 57 | U58 | L1W10 |
| 58 | U59 | L3W10 |
| 59 | U60 | L5W10 |
| 60 | U61 | L2W11 |
| 61 | U62 | L4W11 |
| 62 | U63 | L6W11 |
| 63 | U64 | L1W11 |
| 64 | U65 | L3W11 |
| 65 | U66 | L5W11 |
| 66 | U67 | L2W12 |
| 67 | U68 | L4W12 |
| 68 | U69 | L6W12 |
| 69 | U70 | L1W12 |
| 70 | U71 | L3W12 |
| 71 | U72 | L5W12 |
| 72 | U73 | L2W13 |
| 73 | U74 | L4W13 |
| 74 | U75 | L6W13 |
| 75 | U76 | L1W13 |
| 76 | U77 | L3W13 |
| 77 | U78 | L5W13 |
| 78 | U79 | L2W14 |
| 79 | U80 | L4W14 |
| 80 | U81 | L6W14 |
| 81 | U82 | L1W14 |
| 82 | U83 | L3W14 |
| 83 | U84 | L5W14 |
| 84 | U85 | L2W15 |
| 85 | U86 | L4W15 |
| 86 | U87 | L6W15 |
| 87 | U88 | L1W15 |
| 88 | U89 | L3W15 |
| 89 | U90 | L5W15 |
| 90 | U91 | L2W16 |
| 91 | U92 | L4W16 |
| 92 | U93 | L6W16 |
| 93 | U94 | L1W16 |
| 94 | U95 | L3W16 |
| 95 | U96 | L5W16 |
Runlist
| Run # | Date | Description |
| 4008 | 4/11/13 | set ADB threshold to 100 , installed all 6 STB connectors, key was on the left as you face the ADC crate. Two top PMTs and one bottom PMT were in coincidence. The rate was about 0.5 Hz. at 9:41 on 4/12/13 I observed no voltage coming out of the discriminator monitor, the fuses were NOT blown. Hits seemed to disappear in the data. I recycled the ADB crate power and saw 100 mV on the discriminator monitor. Start a new run 40009 |
| 4009 | 4/12/13 | ADC threshold at 100 mV |
| 4014 | 4/16/13 | Removed cable from J10 connector on ADB crate and becan a cosmic run, the ROC & EB1 segfaulted after 57702 events |
| 4082 | 4/17/13 | first run with fully installed ADC crate & known map; ROC crashed after 5522 event around 20:53 |
| 4099 | 4/17/13 | ROC & EB crash after 4702 events, restarted all processes prior to taking this data |
| 4127 | 4/24/13 | ROC crashed because there was not enough memory for all the data, increased memory in the readoutlist R4127Histos |
After 500 -> 4000 events
EB error message
-- Got all fragments of go thread exit for rocdaq1 get_cb_data returned end of file ROC mask 8 force_end 2 Segmentation fault
ROC error message:
daLogMsg: INFO: Entering User Go daLogMsg: INFO: active, events so far 0 token 0 Segmentation fault
vmeOpenDefaultWindows() from the Download state on the ROC?
[root@rocdaq1 ~]# coda_roc_rc3 -t ROC -n rocdaq1 MSQL DATABASE = LDS CODA 2.6.1,Name : rocdaq1, Type ROC Id : 0 INFO: Starting up rcClient Thread...Running the cMsg RC client, "rocdaq1"
connecting to UDL, cMsg:rc://multicast/LDS
Connect is completed! subscribing subject = rocdaq1 type = run/transition/* subscribing subject = rocdaq1 type = session/control/* subscribing subject = rocdaq1 type = coda/info/* >>>>>> rcClient(Info): Got the request to getState SND END1 >>>>>> rcClient(Info): Got the request to getState callbackControl: Do not understand the command: session/control/setSession Start sending statisitics... >>>>>> rcClient(Info): Got the request to getState SND END1 >>>>>> rcClient(Info): Got the request to getState >>>>>> rcClient(Info): Got the request to getState >>>>>> rcClient(Transition): Got the request to configure Current State: configured Start sending statisitics... callbackControl: Do not understand the command: session/control/setSession >>>>>> rcClient(Info): Got the request to getState daLogMsg: INFO: Downloading configuration "r1dc" daLogMsg: INFO: Downloading readout list /root/linuxvme/r1dc/gen_int_list.so daLogMsg: INFO: _gen_int_list__init() routine found daLogMsg: INFO: readout list loaded rolp->daproc = 0 Init - Initializing new rol structures for GEN_USER Init - Done rolp->daproc = 1 daLogMsg: INFO: Readout list compiled Tue Nov 27 19:07:56 MST 2012 Opening A32 Window (opened at [0xb1a57000,0xb1a67000]) Opening A32Blt Window (opened at [0xa7900000,0xb1900000]) Opening A24 Window (opened at [0xa6900000,0xa7900000]) Opening A16 Window (opened at [0xa68f0000,0xa6900000]) jlabgefMapTsi: Tempe Chip Userspace map successful VME Bus Error IRQ Disabled vmeBusCreateLockShm: vmeBus shared memory mutex created Initialized SIS3610 ID 0 at VME (USER) address 0x3800 (0xa68f3800) daLogMsg: INFO: Initializing TDC 1190 daLogMsg: INFO: User Download Executed daLogMsg: INFO: Downloading readout list /root/linuxvme/r1dc/event_list.so daLogMsg: INFO: _event_list__init() routine found daLogMsg: INFO: readout list loaded rolp->daproc = 0 Init - Initializing new rol structures for ROL2 Init - Done rolp->daproc = 1 daLogMsg: INFO: Readout list compiled Thu Oct 4 13:06:37 MDT 2012 daLogMsg: INFO: User Download 2 Executed daLogMsg: INFO: downloaded Buffer pointer at 0xa666e008 Buffer pointer at 0xa646d008 Buffer pointer at 0xa626c008 Buffer pointer at 0xa606b008 dabufp set to 0xa666e414 ERROR got SIGINT [root@rocdaq1 ~]#
CODA2 DP cpmmunication error
daLogMsg: INFO: opening datalink to eb1:daq2.physics.isu.edu constructor failed : 40839Couldn't open connection to daq2.physics.isu.edu:40839 : Connection refused open_links returned : bad file identifier ""
Readout Map
| Wire | PostAmpOut (CH 1-96) | TDC Channel | |
| L | W | ||
| 5 | 1 | 1 | 1 |
| 3 | 1 | 2 | 2 |
| 1 | 1 | 3 | 3 |
| 6 | 1 | 4 | 4 |
| 4 | 1 | 5 | 5 |
| 2 | 1 | 6 | 6 |
| 5 | 2 | 7 | 7 |
| 3 | 2 | 8 | 8 |
| 1 | 2 | 9 | 9 |
| 6 | 2 | 10 | 10 |
| 4 | 2 | 11 | 11 |
| 2 | 2 | 12 | 12 |
| 5 | 3 | 13 | 13 |
| 3 | 3 | 14 | 14 |
| 1 | 3 | 15 | 15 |
| 6 | 3 | 16 | 16 |
| 4 | 3 | 17 | 17 |
| 2 | 3 | 18 | 18 |
| 5 | 4 | 19 | 19 |
| 3 | 4 | 20 | 20 |
| 1 | 4 | 21 | 21 |
| 6 | 4 | 22 | 22 |
| 4 | 4 | 23 | 23 |
| 2 | 4 | 24 | 24 |
| 5 | 5 | 25 | 25 |
| 3 | 5 | 26 | 26 |
| 1 | 5 | 27 | 27 |
| 6 | 5 | 28 | 28 |
| 4 | 5 | 29 | 29 |
| 2 | 5 | 30 | 30 |
| 5 | 6 | 31 | 31 |
| 3 | 6 | 32 | 32 |
| 1 | 6 | 33 | 33 |
| 6 | 6 | 34 | 34 |
| 4 | 6 | 35 | 35 |
| 2 | 6 | 36 | 36 |
| 5 | 7 | 37 | 37 |
| 3 | 7 | 38 | 38 |
| 1 | 7 | 39 | 39 |
| 6 | 7 | 40 | 40 |
| 4 | 7 | 41 | 41 |
| 2 | 7 | 42 | 42 |
| 5 | 8 | 43 | 43 |
| 3 | 8 | 44 | 44 |
| 1 | 8 | 45 | 45 |
| 6 | 8 | 46 | 46 |
| 4 | 8 | 47 | 47 |
| 2 | 8 | 48 | 48 |
| 5 | 9 | 49 | 49 |
| 3 | 9 | 50 | 50 |
| 1 | 9 | 51 | 51 |
| 6 | 9 | 52 | 52 |
| 4 | 9 | 53 | 53 |
| 2 | 9 | 54 | 54 |
| 5 | 10 | 55 | 55 |
| 3 | 10 | 56 | 56 |
| 1 | 10 | 57 | 57 |
| 6 | 10 | 58 | 58 |
| 4 | 10 | 59 | 59 |
| 2 | 10 | 60 | 60 |
| 5 | 11 | 61 | 61 |
| 3 | 11 | 62 | 62 |
| 1 | 11 | 63 | 63 |
| 6 | 11 | 64 | 64 |
| 4 | 11 | 65 | 65 |
| 2 | 11 | 66 | 66 |
| 5 | 12 | 67 | 67 |
| 3 | 12 | 68 | 68 |
| 1 | 12 | 69 | 69 |
| 6 | 12 | 70 | 70 |
| 4 | 12 | 71 | 71 |
| 2 | 12 | 72 | 72 |
| 5 | 13 | 73 | 73 |
| 3 | 13 | 74 | 74 |
| 1 | 13 | 75 | 75 |
| 6 | 13 | 76 | 76 |
| 4 | 13 | 77 | 77 |
| 2 | 13 | 78 | 78 |
| 5 | 14 | 79 | 79 |
| 3 | 14 | 80 | 80 |
| 1 | 14 | 81 | 81 |
| 6 | 14 | 82 | 82 |
| 4 | 14 | 83 | 83 |
| 2 | 14 | 84 | 84 |
| 5 | 15 | 85 | 85 |
| 3 | 15 | 86 | 86 |
| 1 | 15 | 87 | 87 |
| 6 | 15 | 88 | 88 |
| 4 | 15 | 89 | 89 |
| 2 | 15 | 90 | 90 |
| 5 | 16 | 91 | 91 |
| 3 | 16 | 92 | 92 |
| 1 | 16 | 93 | 93 |
| 6 | 16 | 94 | 94 |
| 4 | 16 | 95 | 95 |
| 2 | 16 | 96 | 96 |
Measurements with source
4/20/12 1hour counts:
SL2 HVB1 Column 18 Row 5
-With source 14459 pulses/1502 sec
4/23/12
SL1 HVB7 column 203 row 4
-With source 50681 pulses/3760 sec.
4/25/12
1 hour counts:
SL2 HVB4 Column 118 row 5
- Without source: 33145 pulses/3610 Sec.
- With source(CS-137):38262 pulses/3600 Sec.
- Without source: 37548 pulses/3715 Sec.
Preamp voltage:5V
Background measurements
HV off 4/5/12 Background counts:
27 pulses/61806 Sec.
SL2 Column 132 row 2
Preamp voltage 6.3V
Discriminator threshold 46mV
Preamp on= 6.3
4/9/12: Back ground count measurements
4531 counts/69564 seconds
2044 counts/24620 seconds
4/10/12 Background counts:
3 pulses/ 74500 sec.
SL1 HVB7 Column 196 Row 2
Preamp voltage 6.3 V
Discriminator threshold 46mV
4/16/12
Background counts:
280 pulses/245850 sec
SL1 HVB7 column 226 row 2
preamp voltage 5V
Discriminator threshold 46mV
4/17/12 Background counts:
6 pulses/62407 sec
SL2 HVB7 column 226 row 8
preamp voltage 5V
discriminator threshold 46mV
4/20/12
Background counts:
63 pulses/ 71724 Sec.
SL1 HVB7 column 226 row 8
Preamp voltage 5V
Discriminator threshold 46mV
4/23/12
Background counts:
41078 pulse/ 245104 sec.
SL1 HVB7 Column 203 Row 4
Preamp voltage 5V
Discriminator threshold 46mV
Cosmic measurements
4/24/12 Cosmic count:
SL1 HVB1 Column 3 Row 10
14534 pulses/11547 sec.
Preamp voltage 5V
4/26/12
Overnight Cosmic pulse count:
SL2 HVB4 Column 118 Row 5
53122 pulses/49793 Sec.
Preamp voltage 5V