Difference between revisions of "Host Computer Configuration"

From New IAC Wiki
Jump to navigation Jump to search
 
(8 intermediate revisions by the same user not shown)
Line 267: Line 267:
 
RAID controller: HP smart Array P410i, slot 0
 
RAID controller: HP smart Array P410i, slot 0
  
 +
 +
daq6.iac.isu.edu 134.50.218.67 HWaddr 80:c1:6e:21:03:92
  
 
The steps used to setup DAQ6 are given below
 
The steps used to setup DAQ6 are given below
Line 294: Line 296:
  
 
==  s3302 on ROCDAQ2==
 
==  s3302 on ROCDAQ2==
 +
 +
[[Struck_SIS3302_ADC]]
  
 
===First check out brand from GitHub===
 
===First check out brand from GitHub===
Line 319: Line 323:
 
libsis3302.so  Makefile  s3302IntTest.c  s3302LibTest.c  s3302ReadSamples  s3302ReadSamples.c  sis3302Lib.h
 
libsis3302.so  Makefile  s3302IntTest.c  s3302LibTest.c  s3302ReadSamples  s3302ReadSamples.c  sis3302Lib.h
  
−
./ s3302ReadSamples
+
[daq@rocdaq2 test]$ ./s3302ReadSamples  
 +
 
 +
JLAB s3302 Lib Tests
 +
----------------------------
 +
s3302SetDebugMask: Debug Mask set to 0x0
 +
 
 +
        ---------- Checking SIS3302 address space ----------
 +
 
 +
        ----------            ALL GOOD            ----------
 +
Opening CRCSR Window (opened at [0xb6fb2000,0xb7fb2000])
 +
Opening A32 Window (opened at [0xb6fa2000,0xb6fb2000])
 +
Opening A32Blt Window (opened at [0xacfa2000,0xb6fa2000])
 +
Opening A24 Window (opened at [0xabfa2000,0xacfa2000])
 +
Opening A16 Window (opened at [0xabf92000,0xabfa2000])
 +
jlabgefMapTsi: Tempe Chip Userspace map successful
 +
VME Bus Error IRQ Disabled
 +
vmeBusCreateLockShm: Creating vmeBus shared memory file
 +
vmeBusMutexInit: Initializing vmeBus mutex
 +
vmeBusCreateLockShm: vmeBus shared memory mutex initialized
 +
Initialized SIS3302  0 at VME (Local) address 0x08000000 (0xacfa2000)
 +
 
 +
STATUS for SIS3302 0 at VME (Local) base address 0x08000000 (0xacfa2000)
 +
--------------------------------------------------------------------------------
 +
ID = 0x3302  Module Revision = 31.05
 +
 
 +
Registers (offset):
 +
  control_status (0x0000) = 0x00000000    modid          (0x0004) = 0x33023105
 +
  irq_config    (0x0008) = 0x00000000    irq_control    (0x000c) = 0x00000000
 +
  acq_control    (0x0010) = 0x00000000    cblt_setup    (0x0030) = 0x00000000
 +
 
 +
CBLT DISABLED
 +
 
 +
Acquisition Control
 +
  Internal Trigger as Trigger    : DISABLED
 +
  Front Panel Trigger Enable    : DISABLED
 +
  Front Panel Timestamp Clear    : DISABLED
 +
  Clock Source                  : 100 MHz - Internal
 +
 
 +
ADC Sampling Logic Busy          : DISABLED
 +
ADC Sampling Logic Armed Bank 1  : DISABLED
 +
ADC Sampling Logic Armed Bank 1  : DISABLED
 +
 
 +
Interrupt                        : DISABLED
 +
  Vector                        : 0x00
 +
  Level                          : 0
 +
  Mode                          : RORA
 +
 
 +
  Status internal IRQ            : CLEAR
 +
  Status VME IRQ                : CLEAR
 +
 
 +
                    EAT  EAT  LEMO
 +
                    EDGE  LEVEL  In 1
 +
Interrupt Sources    0    1    2 
 +
                    ----- ----- -----
 +
          Enabled                   
 +
      Status Flag                   
 +
        Status IRQ                   
 +
 
 +
Interrupt Count  : 0
 +
Acknowledge Count : 0
 +
--------------------------------------------------------------------------------
 +
 
  
−
./s3302ReadSamples: error while loading shared libraries: libjvme.so: cannot open shared object file: No such file or directory
 
  
 +
                      sis3302 Module 0 ADC Configuration/Status
 +
 +
Registers (offset):
 +
GROUP 1
 +
  config      (0x0000) = 0x00000000      EAT        (0x0004) = 0x00000000
 +
  PTAW        (0x0008) = 0x00000000      RDBC        (0x000c) = 0x00000000
 +
GROUP 2
 +
  config      (0x0000) = 0x00020000      EAT        (0x0004) = 0x00000000
 +
  PTAW        (0x0008) = 0x00000000      RDBC        (0x000c) = 0x00000000
 +
GROUP 3
 +
  config      (0x0000) = 0x00040000      EAT        (0x0004) = 0x00000000
 +
  PTAW        (0x0008) = 0x00000000      RDBC        (0x000c) = 0x00000000
 +
GROUP 4
 +
  config      (0x0000) = 0x00060000      EAT        (0x0004) = 0x00000000
 +
  PTAW        (0x0008) = 0x00000000      RDBC        (0x000c) = 0x00000000
 +
 +
 +
    Input  Acc  Trig Enable  ---- Save Raw -----  Test 
 +
Ch  Invert  Mode  Int  Ext    Always PileUp First  Data  Header
 +
--------------------------------------------------------------------------------
 +
1    NO      6    NO  NO      NO    NO    NO    NO  0x0000
 +
2    NO      6    NO  NO      NO    NO    NO    NO  0x0000
 +
3    NO      6    NO  NO      NO    NO    NO    NO  0x0002
 +
4    NO      6    NO  NO      NO    NO    NO    NO  0x0002
 +
5    NO      6    NO  NO      NO    NO    NO    NO  0x0004
 +
6    NO      6    NO  NO      NO    NO    NO    NO  0x0004
 +
7    NO      6    NO  NO      NO    NO    NO    NO  0x0006
 +
8    NO      6    NO  NO      NO    NO    NO    NO  0x0006
 +
--------------------------------------------------------------------------------
 +
 +
    End Event  Pretrig  Trigger Window  -- Raw Data --    Next      Prev
 +
Ch  Threshold  Delay      Length        Start  Length    Addr      Bank
 +
--------------------------------------------------------------------------------
 +
12  0x000000  0x00        0x00          0x00    0x00  0x000000  0x000000
 +
34  0x000000  0x00        0x00          0x00    0x00  0x000000  0x000000
 +
56  0x000000  0x00        0x00          0x00    0x00  0x000000  0x000000
 +
78  0x000000  0x00        0x00          0x00    0x00  0x000000  0x000000
 +
--------------------------------------------------------------------------------
 +
 +
    Peaking Sum  Pulse      Trig
 +
Ch  Time    Gap  Length      Out  GT  Ext  Threshold
 +
--------------------------------------------------------------------------------
 +
12  0x00  0x00  0x00      YES  NO  NO    0x0000
 +
34  0x00  0x00  0x00      YES  NO  NO    0x0000
 +
56  0x00  0x00  0x00      YES  NO  NO    0x0000
 +
78  0x00  0x00  0x00      YES  NO  NO    0x0000
 +
--------------------------------------------------------------------------------
 +
 +
--------------------------------------------------------------------------------
 +
 +
 +
 +
  0: 0x75727590
 +
  1: 0x7573758d
 +
  2: 0x75747592
 +
  3: 0x75707589
 +
  4: 0x75747589
 +
  5: 0x75767595
 +
  6: 0x7576758d
 +
  7: 0x75757591
 +
  8: 0x7570758e
 +
  9: 0x7574758e
 +
 +
  0: 0x75157539
 +
  1: 0x75157538
 +
  2: 0x7517753c
 +
  3: 0x75167538
 +
  4: 0x751e753f
 +
  5: 0x75187533
 +
  6: 0x751c7539
 +
  7: 0x751c753a
 +
  8: 0x75147539
 +
  9: 0x7518753d
 +
  0: 0x758a755d
 +
  1: 0x758a7556
 +
  2: 0x758f755c
 +
  3: 0x758e755a
 +
  4: 0x758d7559
 +
  5: 0x7593755d
 +
  6: 0x7589755b
 +
  7: 0x758d7566
 +
  8: 0x758c755f
 +
  9: 0x758c755b
 +
 +
  0: 0x75be756a
 +
  1: 0x75bc7569
 +
  2: 0x75bc756c
 +
  3: 0x75b37568
 +
  4: 0x75b97568
 +
  5: 0x75b77563
 +
  6: 0x75bd7567
 +
  7: 0x75ba7566
 +
  8: 0x75bf7566
 +
  9: 0x75bf7566
 +
 +
Closing A16 Window
 +
Closing A24 Window
 +
Closing A32Blt Window
 +
Closing A32 Window
 +
Closing CRCSR Window
 +
Calling gefVmeClose
  
 
</pre>
 
</pre>
Line 333: Line 498:
  
 
https://coda.jlab.org/drupal/content/example-single-crate-configuration
 
https://coda.jlab.org/drupal/content/example-single-crate-configuration
 +
 +
 +
the run
 +
 +
jcedit
 +
 +
==Setting up local network==
 +
 +
This describes how to plug your ROC's network card into the Host computers network card so the two can talk without using a network switch
 +
 +
1.) You need a crossover network cable to plug your ROC's NIC into one of the host computes NICs( Network Interface Cards)
 +
 +
2.) Then you need to edit files in the subdirectory
 +
 +
/etc/sysconfig/network-scripts
 +
 +
you will need to create a file with the name
 +
 +
ifcfg-eth0
 +
 +
where "eth0" revers to the name used by your OS to define your network card port (you see this name when you use the "ifconfig" tool)
 +
 +
netools can be used to query the network card port
 +
 +
 +
look at the utility "ethtool"
 +
 +
  
  
  
 
Return to [[Data_Acquisition]] page
 
Return to [[Data_Acquisition]] page

Latest revision as of 23:57, 12 July 2018

DAQ1

Install CentOs

eth1 configuration

The ethernet card on the host computer has two ports (eth0 and eth1).

eth0 is used to talk to the work and use DNS

eth1 is hardwired to a subnet

in this case the ROC is configured to address 10.1.1.2

The eth1 port is set to

"statically set IP addresses"

and the manual IP address setting is 10.1.1.1

after you activate eht1 you can telnet to the ROC using

telnet 10.1.1.2

You can then create an entry in /etc/hosts which aliases roc1 to this IP address

Install tftp onto the Linux host computer

TFTP is used to copy the VxWorks kernel onto the ROC

For CentOS I used yum 

yum install tftp

yum install tftp-server

then I looked in the file 

/etc/xinetd.d/tftp
  1. default: off
  2. description: The tftp server serves files using the trivial file transfer \
  3. protocol. The tftp protocol is often used to boot diskless \
  4. workstations, download configuration files to network-aware printers, \
  5. and to start the installation process for some operating systems.
service tftp

{ 

       socket_type             = dgram
       protocol                = udp
       wait                    = yes
       user                    = root
       server                  = /usr/sbin/in.tftpd
       server_args             = -s /tftpboot
       disable                 = yes
       per_source              = 11
       cps                     = 100 2
       flags                   = IPv4

}

to see how tftp was configured by default. The file tell me that the tftp files should be located in the subdirectory

/tftpboot

make sure your boot kernels are located in /tftpboot 

[root@daq1 /]# ls tftpboot/
boot6100_121_v3.bin  boot6100_122.bin

turn the server on

/sbin/chkconfig tftp on

Set up rsh

turn on rsh

use yum to install the rsh server. 

yum install rsh-server

edit /etc/xinetd.d/rlogin and rsh to allow server 

# default: on
# description: rlogind is the server for the rlogin(1) program.  The server \
#       provides a remote login facility with authentication based on \
#       privileged port numbers from trusted hosts.
service login
{
       socket_type             = stream
       wait                    = no
       user                    = root
       log_on_success          += USERID
       log_on_failure          += USERID
       server                  = /usr/sbin/in.rlogind
       disable                 = no
}

Now reload xinitd 

/etc/init.d/xinetd reload


then add a file called ".rhosts" to the daq account with the IP addresses and usernames


~ >less .rhosts 

 134.50.3.210 daq
 10.1.1.2 roc1

old version is below
~ >less .rhosts
 134.50.3.216 roc1
 134.50.3.216 daq
 134.50.3.210 daq

You Must set the .rhosts permissions exaclty as below otherwise rsh will not work 

chmod 644 .rhosts

Update hosts file

set /etc/hosts file to say 

# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1       localhost.localdomain localhost
#::1            localhost6.localdomain6 localhost6
134.50.3.210    daq1.physics.isu.edu    daq1
10.1.1.1        localdaq.physics.isu.edu        localdaq
10.1.1.2        roc1.physics.isu.edu    roc1

the above will assign IP addesses to computer names

test to see if rsh is running

rsh -l daq daq1 ls


if you get the error like 

[root@daq1 xinetd.d]# rsh -l daq daq1 ls
connect to address 134.50.3.210 port 544: Connection refused
Trying krb4 rsh...
connect to address 134.50.3.210 port 544: Connection refused
trying normal rsh (/usr/bin/rsh)

the check if rsh is enabled 

[root@daq1 xinetd.d]# less /etc/xinetd.d/rsh
# default: on
# description: The rshd server is the server for the rcmd(3) routine and, \
#       consequently, for the rsh(1) program.  The server provides \
#       remote execution facilities with authentication based on \
#       privileged port numbers from trusted hosts.
service shell
{
        socket_type             = stream
        wait                    = no
        user                    = root
        log_on_success          += USERID
        log_on_failure          += USERID
        server                  = /usr/sbin/in.rshd
        disable                 = no
}

You need to reload xinetd if you make a change so it looks like above 

[root@daq1 xinetd.d]# /etc/init.d/xinetd reload

Security/Firewall

Turn off iptables

/sbin/service iptables stop

Turn off Kerberos

How can I > configure rsh to use the old, normal way of auth? > > I'm using the latest CentOS4.2

If you don't use the Kerberos stuff, then remove it ... it's probably the krb5-workstation package - i.e.

rpm -e krb5-workstation

I don't know about rexec, but for rlogin and rsh:

Edit /etc/pam.d/rsh and change the line:

auth required pam_rhosts_auth.so

to:

auth required pam_rhosts_auth.so promiscuous

and edit /etc/pam.d/rlogin and change the line:

auth sufficient pam_rhosts_auth.so

to:

auth sufficient pam_rhosts_auth.so promiscuous


Make sure 'rsh' and 'rlogin' are listed in /etc/securetty


text relocation

SummarySELinux is preventing rcServer from loading /home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so which requires text relocation.

Detailed Description
[SELinux is in permissive mode, the operation would have been denied but was permitted due to permissive mode.]

The rcServer application attempted to load /home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so which requires text relocation. This is a potential security problem. Most libraries do not need this permission. Libraries are sometimes coded incorrectly and request this permission. The SELinux Memory Protection Tests web page explains how to remove this requirement. You can configure SELinux temporarily to allow /home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so to use relocation as a workaround, until the library is fixed. Please file a bug report against this package.

Allowing Access
If you trust /home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so to run correctly, you can change the file context to textrel_shlib_t. "chcon -t textrel_shlib_t '/home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so'" You must also change the default file context files on the system in order to preserve them even on a full relabel. "semanage fcontext -a -t textrel_shlib_t '/home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so'"

The following command will allow this access:chcon -t textrel_shlib_t '/home/daq/CODA/2.5/CMLOG/2.1/lib/Linux/libcmlog.so'Additional Information

Dual head config

The DAQ computer is running a Matrox display adapter


http://projects.tuxx-home.at/?id=matrox_drivers

VME crate modules

Module address
CAEN_V1495_IO 0x80110000
CAEN_V775_TDC 0x610000
CAEN_V792_ADC 0xee0000
CAEN_V260_Scalr 0xda0000
Struck_SIS3302_ADC 0x50000000

SIS3300 Library

try the following on roc1 

-> ld < sis3320Lib.o

try to initialize module 

s3320Init(0x5000000,0,1)

DAQ6 configuration

DAQ6_Specs

Machine: Enterprise HP ProLiant DL380 G7 CPUs: 2, 2.93 GHz CPUs with totaling 8 cores RAID controller: HP smart Array P410i, slot 0


daq6.iac.isu.edu 134.50.218.67 HWaddr 80:c1:6e:21:03:92

The steps used to setup DAQ6 are given below

CentOS 7 installation

DAQ6_CentOS7_install

configure rocdaq6

I copied all the software for CODA 3.06 from the host computer daq6 to the ROC

scp -r 3.06 rocdaq2:CODA/

then i copied the setup file from the host to the ROC. Since the account on the ROC is a mirror of the account on the host, I did not need to change the setup file.


When I tried to compile a readout lit on the ROC using the command

make -f Makefile-rol I got the error message 

rol.h: no such file or directory


I need to setup the ROC to compile readout lists.

s3302 on ROCDAQ2

Struck_SIS3302_ADC

First check out brand from GitHub

login ro rocdaq2

then download the source under CODA 3.06 linuxvme src subdirectory 

cd CODA/3.06/linuxvme/src/

git clone -b feature-nGamma_firmware https://github.com/JeffersonLab/sis3302.git

cd sis3302

 make -B

cd test

[daq@rocdaq2 test]$ make -B s3302ReadSamples
echo "Making s3302ReadSamples"
Making s3302ReadSamples
cc  -Wall -O2 -I. -I.. -I/home/daq/CODA/3.06/linuxvme/include -L. -L.. -L/home/daq/CODA/3.06/linuxvme/lib -DJLAB -g -o s3302ReadSamples s3302ReadSamples.c -lrt -ljvme -lsis3302
[daq@rocdaq2 test]$ ls
libsis3302.so  Makefile  s3302IntTest.c  s3302LibTest.c  s3302ReadSamples  s3302ReadSamples.c  sis3302Lib.h

[daq@rocdaq2 test]$ ./s3302ReadSamples 

JLAB s3302 Lib Tests
----------------------------
s3302SetDebugMask: Debug Mask set to 0x0

         ---------- Checking SIS3302 address space ---------- 

         ----------            ALL GOOD            ---------- 
Opening CRCSR Window (opened at [0xb6fb2000,0xb7fb2000])
Opening A32 Window (opened at [0xb6fa2000,0xb6fb2000])
Opening A32Blt Window (opened at [0xacfa2000,0xb6fa2000])
Opening A24 Window (opened at [0xabfa2000,0xacfa2000])
Opening A16 Window (opened at [0xabf92000,0xabfa2000])
jlabgefMapTsi: Tempe Chip Userspace map successful
VME Bus Error IRQ Disabled
vmeBusCreateLockShm: Creating vmeBus shared memory file
vmeBusMutexInit: Initializing vmeBus mutex
vmeBusCreateLockShm: vmeBus shared memory mutex initialized
Initialized SIS3302  0 at VME (Local) address 0x08000000 (0xacfa2000) 

STATUS for SIS3302 0 at VME (Local) base address 0x08000000 (0xacfa2000)
--------------------------------------------------------------------------------
 ID = 0x3302   Module Revision = 31.05 

 Registers (offset):
  control_status (0x0000) = 0x00000000    modid          (0x0004) = 0x33023105
  irq_config     (0x0008) = 0x00000000    irq_control    (0x000c) = 0x00000000
  acq_control    (0x0010) = 0x00000000    cblt_setup     (0x0030) = 0x00000000

 CBLT DISABLED

 Acquisition Control
   Internal Trigger as Trigger    : DISABLED
   Front Panel Trigger Enable     : DISABLED
   Front Panel Timestamp Clear    : DISABLED
   Clock Source                   : 100 MHz - Internal

 ADC Sampling Logic Busy          : DISABLED
 ADC Sampling Logic Armed Bank 1  : DISABLED
 ADC Sampling Logic Armed Bank 1  : DISABLED

 Interrupt                        : DISABLED
   Vector                         : 0x00
   Level                          : 0
   Mode                           : RORA

   Status internal IRQ            : CLEAR
   Status VME IRQ                 : CLEAR

                     EAT   EAT   LEMO
                    EDGE  LEVEL  In 1
 Interrupt Sources    0     1     2  
                    ----- ----- -----
           Enabled                     
       Status Flag                     
        Status IRQ                     

 Interrupt Count   : 0
 Acknowledge Count : 0
--------------------------------------------------------------------------------



                      sis3302 Module 0 ADC Configuration/Status

 Registers (offset):
 GROUP 1
  config      (0x0000) = 0x00000000       EAT         (0x0004) = 0x00000000
  PTAW        (0x0008) = 0x00000000       RDBC        (0x000c) = 0x00000000
 GROUP 2
  config      (0x0000) = 0x00020000       EAT         (0x0004) = 0x00000000
  PTAW        (0x0008) = 0x00000000       RDBC        (0x000c) = 0x00000000
 GROUP 3
  config      (0x0000) = 0x00040000       EAT         (0x0004) = 0x00000000
  PTAW        (0x0008) = 0x00000000       RDBC        (0x000c) = 0x00000000
 GROUP 4
  config      (0x0000) = 0x00060000       EAT         (0x0004) = 0x00000000
  PTAW        (0x0008) = 0x00000000       RDBC        (0x000c) = 0x00000000


     Input   Acc   Trig Enable   ---- Save Raw -----   Test  
Ch   Invert  Mode   Int  Ext     Always PileUp First   Data  Header
--------------------------------------------------------------------------------
 1     NO      6     NO   NO       NO     NO     NO     NO   0x0000
 2     NO      6     NO   NO       NO     NO     NO     NO   0x0000
 3     NO      6     NO   NO       NO     NO     NO     NO   0x0002
 4     NO      6     NO   NO       NO     NO     NO     NO   0x0002
 5     NO      6     NO   NO       NO     NO     NO     NO   0x0004
 6     NO      6     NO   NO       NO     NO     NO     NO   0x0004
 7     NO      6     NO   NO       NO     NO     NO     NO   0x0006
 8     NO      6     NO   NO       NO     NO     NO     NO   0x0006
--------------------------------------------------------------------------------

    End Event  Pretrig  Trigger Window   -- Raw Data --     Next      Prev
Ch  Threshold  Delay       Length        Start   Length     Addr      Bank
--------------------------------------------------------------------------------
12   0x000000   0x00        0x00           0x00    0x00   0x000000  0x000000
34   0x000000   0x00        0x00           0x00    0x00   0x000000  0x000000
56   0x000000   0x00        0x00           0x00    0x00   0x000000  0x000000
78   0x000000   0x00        0x00           0x00    0x00   0x000000  0x000000
--------------------------------------------------------------------------------

    Peaking Sum   Pulse       Trig
Ch  Time    Gap   Length      Out   GT  Ext   Threshold
--------------------------------------------------------------------------------
12   0x00   0x00   0x00       YES   NO   NO    0x0000
34   0x00   0x00   0x00       YES   NO   NO    0x0000
56   0x00   0x00   0x00       YES   NO   NO    0x0000
78   0x00   0x00   0x00       YES   NO   NO    0x0000
--------------------------------------------------------------------------------

--------------------------------------------------------------------------------



   0: 0x75727590
   1: 0x7573758d
   2: 0x75747592
   3: 0x75707589
   4: 0x75747589
   5: 0x75767595
   6: 0x7576758d
   7: 0x75757591
   8: 0x7570758e
   9: 0x7574758e

   0: 0x75157539
   1: 0x75157538
   2: 0x7517753c
   3: 0x75167538
   4: 0x751e753f
   5: 0x75187533
   6: 0x751c7539
   7: 0x751c753a
   8: 0x75147539
   9: 0x7518753d
  0: 0x758a755d
   1: 0x758a7556
   2: 0x758f755c
   3: 0x758e755a
   4: 0x758d7559
   5: 0x7593755d
   6: 0x7589755b
   7: 0x758d7566
   8: 0x758c755f
   9: 0x758c755b

   0: 0x75be756a
   1: 0x75bc7569
   2: 0x75bc756c
   3: 0x75b37568
   4: 0x75b97568
   5: 0x75b77563
   6: 0x75bd7567
   7: 0x75ba7566
   8: 0x75bf7566
   9: 0x75bf7566

Closing A16 Window
Closing A24 Window
Closing A32Blt Window
Closing A32 Window
Closing CRCSR Window
Calling gefVmeClose

Database creation on daq6

Using jcedit

followed the URL below and made two configurations, one titled "SIS3610" that is to be used for rocdaq1 and one entitle "rc2sis3610" that will be used for rocdaq2.

https://coda.jlab.org/drupal/content/example-single-crate-configuration


the run 

jcedit

Setting up local network

This describes how to plug your ROC's network card into the Host computers network card so the two can talk without using a network switch

1.) You need a crossover network cable to plug your ROC's NIC into one of the host computes NICs( Network Interface Cards)

2.) Then you need to edit files in the subdirectory

/etc/sysconfig/network-scripts

you will need to create a file with the name

ifcfg-eth0

where "eth0" revers to the name used by your OS to define your network card port (you see this name when you use the "ifconfig" tool)

netools can be used to query the network card port


look at the utility "ethtool"



Return to Data_Acquisition page

Retrieved from "https://wiki.iac.isu.edu/index.php?title=Host_Computer_Configuration&oldid=124117"