Difference between revisions of "DDP:Detailed Design Phase: Drawing and Assembly Package"

From New IAC Wiki
Jump to navigation Jump to search
 
(57 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
Detailed Design Drawing Report 6/27/08
 
Detailed Design Drawing Report 6/27/08
  
Outline:
+
=Introduction=
 
 
1.) Dimensions
 
 
 
2.) Constraints: Case 3 from progress report: constrain triangle and nose plate on upstream side.
 
 
 
3.) Deflection Analysis
 
 
 
Steps:
 
 
 
a.) check triangle contact region and its mass
 
b.) add another carbon fiber rod
 
c.) increase size of back plate
 
 
 
 
 
4.) Drawings
 
 
 
drawings in PDF format
 
 
 
a.) Endplate structural drawing (no holes just shaded area)
 
 
 
b.) Drawings for all other parts
 
 
 
c.)
 
 
 
d.) Copy old R3 (take advantage of no curved window.
 
 
 
 
 
=Report=
 
 
 
==Introduction==
 
  
 
The CLAS12 Drift chamber has 3 regions arranged as shown below
 
The CLAS12 Drift chamber has 3 regions arranged as shown below
Line 38: Line 8:
  
  
The electrons released from the target center will flow through region 1, region 2 and region 3. All these regions look the same way. However, their sizes and the materials with which they are made are different. Due to the fact their sizes are different; some of them have some structural add-ons to support their structural abilities. The chambers are arranged in such a way that every chamber receives the same number of electrons. Apart from that, the chambers were shaped in such a way that all the electrons travel approximately the same distance before they hit a particular chamber.  
+
The electrons scatter from the target center will travel through region 1, region 2 and region 3. All these regions look the same way. However, their sizes and the materials with which they are made are different. Due to the fact their sizes are different; some of them have some structural add-ons to support their structural abilities. The chambers are arranged in such a way that every chamber receives the same number of electrons. Apart from that, the chambers were shaped in such a way that all the electrons travel approximately the same distance before they hit a particular chamber.  
  
 
[[Image:jul17_2008_3.png| 300 px]]
 
[[Image:jul17_2008_3.png| 300 px]]
Line 46: Line 16:
  
 
Although these pieces are termed as triangular, these are not triangular in reality. The nose which is the smallest of all is very small compared to the other plates, which will make us to visualize this as a triangular piece. Ar Co2 (90/10) gas is maintained in each of these chambers at an operating pressure of 0.001444 Psi and a peak pressure 5 times higher.  
 
Although these pieces are termed as triangular, these are not triangular in reality. The nose which is the smallest of all is very small compared to the other plates, which will make us to visualize this as a triangular piece. Ar Co2 (90/10) gas is maintained in each of these chambers at an operating pressure of 0.001444 Psi and a peak pressure 5 times higher.  
In turn there are about 4928 very sensitive wires (112 Sense wires with 44 Wire Layers) connected across the plates inside each piece.
+
In turn there are about 4928 wires (112 Sense wires with 44 Wire Layers) connected across the plates inside each piece.
  
 
===Design Criteria===
 
===Design Criteria===
Line 53: Line 23:
 
Initial parameters to be followed to fulfill to satisfy design Criteria
 
Initial parameters to be followed to fulfill to satisfy design Criteria
  
1. Distance from target to first sense wire plane along a ray which is normal to the end plate = 4746.5 mm
+
 +
{| border="1"  |cellpadding="20" cellspacing="0
  
2. Chamber Tilt Angle = 25 Degrees
+
|-
 +
| Distance from target to first sense wire plane along a ray which is normal to the end plate || 4746.5 mm
 +
|-
 +
Chamber Tilt Angle|| 25 Degrees
 +
|-
 +
|  Maximum Scattering Angle || 45.05 Degrees
 +
|-
 +
|  Minimum Scattering Angle || 4.5 Degrees
 +
|-
 +
| Angle of the wires to the horizontal || 6 Degrees
 +
|-
 +
| Max end plate deflection  || 50 <math>\mu</math>m
 +
|
 +
|}
  
3. Maximum Scattering Angle = 45.05 Degrees
 
 
4. Minimum Scattering Angle = 4.5 Degrees
 
 
5. Wires are at 6 Degrees to the horizontal in each of its wire planes
 
  
  
Line 68: Line 47:
 
[[Image:jun20_2008_3.png| 300 px]]
 
[[Image:jun20_2008_3.png| 300 px]]
  
 +
=Introduction to Assembly=
 +
 +
[[Image:R3BreakOutDiagram.jpg]]
 +
 +
Paragraph defining all the parts
 +
 +
==Nose Plate==
  
===Wire pattern===
+
Nose Plate: [[Image:assembly20_jun_1.png| 200 px]]
  
The wire pattern at the center plane will be symmetric and easy to understand. The wire pattern in each super layer on this plane is same and a view at this wires at this plane will be as follows
+
Nose Plate will be made of rigid material such as solid aluminum, since the supporting mechanism will be attached to these plates. The nose plate will connect the bottoms of the two end plated and provides the interface.
 +
 
 +
== End Plate ==
  
[[Image:jun20_2008_4.png| 500 px]]
+
End Plate: [[Image:assembly17_jul_4.png| 200 px]]
  
In the horizontal direction we have 6 six sense wires. so, there will be a 2 + 6 times 3 + 2 = 22 wire planes as shown in the fig. If the distance between each wire plane is 'H' mm. Then the total span of wires in this direction will be 21H mm.
+
The End plate is about 4830 mm and 4665mm in length along the longitudinal length and about 525mm in width. It has approximately about 5000 holes with an approximate diameter of 6mm on the surface and about 9mm inside the surface. There will be two End plates names as Right End plate and Left End plate which are located to the actual right and left side of each sector when viewed from the target center respectively.
  
In the vertical direction, there are 112 sense wires, so there will be 2 + 112 + 2 = 116 wire planes as shown. If the distance between each wire plane is 'V' mm. Then, the total span in this direction will be 115V mm
 
  
H = ?
 
  
V = ?
+
==Back Plate==
  
No. of sense wires in each super layer = ?
+
Back Plate: [[Image:assembly17_jul_5.png| 200 px]] It is the plate which connects the top edges of both the end plates and holds the fixtures settings
  
No. of field wires in each super layer = ?
+
==Carbon Rods==
  
No. of guard wires in each super layer = ?
+
Carbon Rods: [[Image:assembly17_jul_6.png| 200 px]]
  
 +
To provide rigidity, there will be several carbon rods fixed in between both the end plates and they vary in length depending on no.of carbon rods used and the location of rods. These rods are hollow to reduce the electron dissipation in the section.
  
 +
== Upstream Window and Downstream Window's==
  
==Introduction to Assembly==
+
Upstream Window and Downstream Window's:[[Image:assembly17_jul_7.png| 200 px]]
  
Nose Plate: [[Image:assembly20_jun_1.png| 200 px]]
+
Upstream Window is the thin Mylar sheet of about 1/1000th of an inch crimped or glued on the upstream side of electron flow slightly after the carbon rods. Downstream Window is a Hexcel honeycomb material provided on the downstream side to help support the assembly, to provide rigidity and to enclose each sector
  
Nose Plate will be made of rigid material such as solid aluminum, since the supporting mechanism will be attached to these plates. The nose plate will connect the bottoms of the two end plated and provides the interface.
+
==Wire pattern==
  
 +
The wire pattern at the center plane will be symmetric and easy to understand. The wire pattern in each super layer on this plane is same and a view at this wires at this plane will be as follows
  
End Plate: [[Image:assembly17_jul_4.png| 200 px]]
+
[[Image:jun20_2008_4.png| 500 px]]
  
The End plate is about 4830 mm and 4665mm in length along the longitudinal length and about 525mm in width. It has approximately about 5000 holes with an approximate diameter of 6mm on the surface and about 9mm inside the surface. There will be two End plates names as Right End plate and Left End plate which are located to the actual right and left side of each sector when viewed from the target center respectively.
+
In the horizontal direction we have 6 six sense wires. so, there will be a 2 + 6 times 3 + 2 = 22 wire planes as shown in the fig. If the distance between each wire plane is 'H' mm. Then the total span of wires in this direction will be 21H mm.
  
Back Plate: [[Image:assembly17_jul_5.png| 200 px]] It is the plate which connects the top edges of both the end plates and holds the fixtures settings
+
In the vertical direction, there are 112 sense wires, so there will be 1 + 1 (guard wire) + 112 (sense Wires) + 112 (Field wires) + 1 + 1 (Guard wire) = 228 wire planes as shown. If the distance between each wire plane is 'V' mm. Then, the total span in this direction will be 227V mm
  
Carbon Rods: [[Image:assembly17_jul_6.png| 200 px]]
+
H = 9 mm
  
To provide rigidity, there will be several carbon rods fixed in between both the end plates and they vary in length depending on no.of carbon rods used and the location of rods. These rods are hollow to reduce the electron dissipation in the section.
+
V = 15.5884 mm
  
Upstream Window and Downstream Window's:[[Image:assembly17_jul_7.png| 200 px]]
+
No. of sense wires in each super layer = ?
  
Upstream Window is the thin Mylar sheet of about 1/1000th of an inch crimped or glued on the upstream side of electron flow slightly after the carbon rods. Downstream Window is a Hexcel honeycomb material provided on the downstream side to help support the assembly, to provide rigidity and to enclose each sector
+
No. of field wires in each super layer = ?
  
[[Image:R3BreakOutDiagram.jpg]]
+
No. of guard wires in each super layer = ?
  
==Analysis==
+
=Analysis=
  
 
To determine the stability of the design, various sets of analysis were performed under different constraint and loading conditions. Sometimes each of the part was analyzed individually and also in the assembly. Some parts were analyzed for different materials
 
To determine the stability of the design, various sets of analysis were performed under different constraint and loading conditions. Sometimes each of the part was analyzed individually and also in the assembly. Some parts were analyzed for different materials
Line 311: Line 300:
 
|}
 
|}
  
=====Fixed Carbon Rod locations=====  
+
=====Fixing the carbon Rod locations on the end plate=====  
  
 
In this analysis, the end plate is a straight rectangular shaped sheet. six carbon rods were assumed and the locations where the carbon rods are attached to the end plate are fixed for analysis. FR-3700 Foam with slices of steel is considered for this analysis. Effective Material properties were used wherever required. The short sided edges of the rectangular end plate is considered to be fixed pretending a cantilever beam.
 
In this analysis, the end plate is a straight rectangular shaped sheet. six carbon rods were assumed and the locations where the carbon rods are attached to the end plate are fixed for analysis. FR-3700 Foam with slices of steel is considered for this analysis. Effective Material properties were used wherever required. The short sided edges of the rectangular end plate is considered to be fixed pretending a cantilever beam.
Line 322: Line 311:
 
|}
 
|}
  
=====Fixed Carbon Rod and Hexcel side edges=====
+
=====Fixing both Carbon Rod and Hexcel side edges on the end plate=====
  
 
Deflection Analysis of the End plate (Slices of Polyurethane and Steel) with fixed carbon rods and Hexcel foam sheet edges
 
Deflection Analysis of the End plate (Slices of Polyurethane and Steel) with fixed carbon rods and Hexcel foam sheet edges
Line 349: Line 338:
 
{| align="center" border="0"   
 
{| align="center" border="0"   
 
|-
 
|-
|[[Image:jul17_2008_10.png| 500 px]]
+
|[[Image:jul17_2008_10.png| 300 px]]
 
|-
 
|-
|[[Image:jul17_2008_11.png| 500 px]]  
+
|[[Image:jul17_2008_11.png| 300 px]]  
 
|-
 
|-
 
|[[Image:jul17_2008_12.png| 500 px]]
 
|[[Image:jul17_2008_12.png| 500 px]]
Line 407: Line 396:
 
{| align="center" border="0"   
 
{| align="center" border="0"   
 
|-
 
|-
|[[Image:CarbonRodBuckling_AnsysCalc1.jpg| 500 px]]
+
|[[Image:CarbonRodBuckling_AnsysCalc1.jpg| 300px]]
 
|-
 
|-
 
| Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle.
 
| Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle.
Line 418: Line 407:
 
{| align="center" border="0"   
 
{| align="center" border="0"   
 
|-
 
|-
|[[Image:CarbonRodBuckling_AnsysCalc2.jpg| 500 px]]
+
|[[Image:CarbonRodBuckling_AnsysCalc2.jpg| 300px]]
 
|-
 
|-
 
| Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle with the real constraints.
 
| Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle with the real constraints.
Line 438: Line 427:
 
•      For Very thin sheets like mylar, Large deflection membrane stiffened analysis is proven to be accurate and the same is otherwise termed as loading with normal and membrane stress approach and is detailed, Please follow the link [[Deformation with both Normal and Membrane Stress approach]]
 
•      For Very thin sheets like mylar, Large deflection membrane stiffened analysis is proven to be accurate and the same is otherwise termed as loading with normal and membrane stress approach and is detailed, Please follow the link [[Deformation with both Normal and Membrane Stress approach]]
  
[[Image:mylar_analysis_table1.jpg]]
+
[[Image:mylar_analysis_table1.jpg| 500px]]
  
 
===Assembly Analysis===
 
===Assembly Analysis===
Line 446: Line 435:
 
2. By modeling hexcel sheet in the assembly and by replacing the rectangular constraints with circular constraints, we have considerable change in the numbers for deflection and can be observed at [[kalyan_16_may_08]]
 
2. By modeling hexcel sheet in the assembly and by replacing the rectangular constraints with circular constraints, we have considerable change in the numbers for deflection and can be observed at [[kalyan_16_may_08]]
  
3. The Hinge locations were moved from Upstream side to the downstream side and the results can be observed at [[kalyan_23_may_08]]
+
3. The Hinge locations were moved from Upstream side to the downstream side and the results can be observed at [[kalyan_23_May_08]]
  
 
4. To reduce the max deformation, the diameter of the carbon rods and the thickness were gradually increased and the results were tabulated as follows
 
4. To reduce the max deformation, the diameter of the carbon rods and the thickness were gradually increased and the results were tabulated as follows
Line 467: Line 456:
 
Follow the link for images and PDF result files. The new results can be observed at [[kalyan_23_May_08_2.1]]
 
Follow the link for images and PDF result files. The new results can be observed at [[kalyan_23_May_08_2.1]]
  
5. An Extra carbon rod is introduced to the geometry on the downstream side behind the hexcel sheet with various diameters and thicknesses and the results can be found at [[kalyan_23_may_08_2.2]]
+
5. An Extra carbon rod is introduced to the geometry on the downstream side behind the hexcel sheet with various diameters and thicknesses and the results can be found at [[kalyan_23_May_08_2.2]]
  
 
6. In the next approach, the thickness of the polyurethane layer in the end plates were increased from 2 inches to 2.5 inches with carbon rods of 3.5 inch diameter and 0.5 inch thk including the single rear carbon rod.
 
6. In the next approach, the thickness of the polyurethane layer in the end plates were increased from 2 inches to 2.5 inches with carbon rods of 3.5 inch diameter and 0.5 inch thk including the single rear carbon rod.
Line 484: Line 473:
 
Follow the link for images and PDF result files. The new results can be observed at [[kalyan_23_May_08_2.3]]
 
Follow the link for images and PDF result files. The new results can be observed at [[kalyan_23_May_08_2.3]]
  
7.
+
7. The aluminum casing width is increased by 30 mm, This increase is made on the upstream side between the aluminum slits and upstream side hole area, Triangular constraint areas were introduced to the geometry and the constraints were applied on them.
 +
 
 +
Sector 1 is studied under 6 cases of analysis.
 +
* Case 1: Triangular Constraints are only in the downstream side and only upstream side on the nose plate
 +
* Case 3: Triangular Constraints are only in the upstream side and only upstream side on the nose plate
 +
* Case 5: Triangular Constraints are in both upstream and downstream side and only upstream side on the nose plate
 +
* Case 2, Case 4, Case 6: are with both upstream and downstream side constraints on the nose plate for case 1, 3, 5 respectively
 +
For Details, Follow the link for images and PDF result files. The new results can be observed at [[kalyan_30_May_08]]
 +
 
 +
=Drawings=
 +
==First set of drawings==
 +
List of drawings
 +
 
 +
{| border="1"  |cellpadding="20" cellspacing="0
 +
|-
 +
|S. No || Drawing No|| Description || Link
 +
|-
 +
| 1|| B00000-01-10-0001 || Basic sector assembly ||[[Image:B00000-01-10-0001.pdf]]
 +
|-
 +
| 2|| B00000-01-10-0002 || Detailed drawing of Nose plate ||[[Image:B00000-01-10-0002.pdf]]
 +
|-
 +
| 3|| B00000-01-10-0003 || Detailed drawing of right end plate Core ||[[Image:B00000-01-10-0003.pdf]]
 +
|-
 +
| 4|| B00000-01-10-0004 || Detailed drawing of right end plate skin ||[[Image:B00000-01-10-0004.pdf]]
 +
|-
 +
| 5|| B00000-01-10-0005 || Detailed drawing of End plate casing ||[[Image:B00000-01-10-0005.pdf]]
 +
|-
 +
| 6|| B00000-01-10-0006 || Detailed drawing of Left end plate Core ||[[Image:B00000-01-10-0006.pdf]]
 +
|-
 +
| 7|| B00000-01-10-0007 || Detailed drawing of Left end plate skin ||[[Image:B00000-01-10-0007.pdf]]
 +
|-
 +
| 8|| B00000-01-10-0008 || Detailed drawing of back plate Core ||[[Image:B00000-01-10-0008.pdf]]
 +
|-
 +
| 9|| B00000-01-10-0009 || Detailed drawing of back plate skin ||[[Image:B00000-01-10-0009.pdf]]
 +
|-
 +
| 10|| B00000-01-10-0010|| Detailed drawing of back plate casing ||[[Image:B00000-01-10-0010.pdf]]
 +
|-
 +
| 11|| B00000-01-10-0011|| Detailed drawing of back plate Core ||[[Image:B00000-01-10-0011.pdf]]
 +
|-
 +
| 12|| B00000-01-10-0012|| Detailed drawing of back plate skin ||[[Image:B00000-01-10-0012.pdf]]
 +
|-
 +
| 13|| B00000-01-10-0013|| Detailed drawing of carbon fiber rods ||[[Image:B00000-01-10-0013.pdf]]
 +
|}
  
==Drawings==
 
  
 
The Assembly of each sector in the region 3 drift chamber can be considered similar to each other.
 
The Assembly of each sector in the region 3 drift chamber can be considered similar to each other.
Line 505: Line 535:
 
7. Attachments: These are the external geometric parts of each sector, used for clamping and mounting each sector. so, they might change with the orientation of each sector
 
7. Attachments: These are the external geometric parts of each sector, used for clamping and mounting each sector. so, they might change with the orientation of each sector
  
A detailed drawing of this Basic sector assmebly can be viewed at [[Image:B00000-01-10-0001.pdf]]
+
A detailed drawing of this Basic sector assembly can be viewed at [[Image:B00000-01-10-0001.pdf]]
  
  
Line 512: Line 542:
 
Nose plate is the plate where both the end plates are attached to it on either side
 
Nose plate is the plate where both the end plates are attached to it on either side
  
[[Image:assembly20_jun_1.png| 600 px]]
+
[[Image:assembly20_jun_1.png| 300 px]]
  
 
A detailed drawing of Nose plate can be viewed at [[Image:B00000-01-10-0002.pdf]]
 
A detailed drawing of Nose plate can be viewed at [[Image:B00000-01-10-0002.pdf]]
Line 520: Line 550:
 
Left end plate is the end plate to the left hand side if we are viewing from the target.
 
Left end plate is the end plate to the left hand side if we are viewing from the target.
  
[[Image:assembly20_jun_2.png| 600 px]]
+
[[Image:assembly20_jun_2.png| 300 px]]
  
 
They can be referenced with left and right to show each sub assembly.
 
They can be referenced with left and right to show each sub assembly.
Line 537: Line 567:
 
Left end plate and the right end plate are same with parts and its dimensions. However, the hole locations differ between each other.
 
Left end plate and the right end plate are same with parts and its dimensions. However, the hole locations differ between each other.
  
[[Image:assembly20_jun_2.png| 600 px]]
+
[[Image:assembly20_jun_2.png| 300 px]]
  
 
Each end plate sub assembly consists of 3 parts, namely
 
Each end plate sub assembly consists of 3 parts, namely
Line 543: Line 573:
 
End plate casing - Made of Aluminum.
 
End plate casing - Made of Aluminum.
  
[[Image:assembly20_jun_5.png| 600 px]]
+
[[Image:assembly20_jun_5.png| 300 px]]
  
  
Line 556: Line 586:
 
Back plate is the plate which connects the left end plate and right end plate on the top.
 
Back plate is the plate which connects the left end plate and right end plate on the top.
  
[[Image:assembly20_jun_10.png| 600 px]]
+
[[Image:assembly20_jun_10.png| 300 px]]
  
 
Back plate sub assembly consists of 3 parts, namely
 
Back plate sub assembly consists of 3 parts, namely
Line 562: Line 592:
 
Back plate Core - made of Polyurethane
 
Back plate Core - made of Polyurethane
  
[[Image:assembly20_jun_11.png| 400 px]]
+
[[Image:assembly20_jun_11.png| 300 px]]
  
 
Back plate Skins - 2 No's- Made of stainless steel
 
Back plate Skins - 2 No's- Made of stainless steel
  
[[Image:assembly20_jun_12.png| 400 px]]
+
[[Image:assembly20_jun_12.png| 300 px]]
  
 
Back plate casing - Made of Aluminum
 
Back plate casing - Made of Aluminum
  
[[Image:assembly20_jun_13.png| 400 px]]
+
[[Image:assembly20_jun_13.png| 300 px]]
  
 
A detailed drawing of back plate Core can be viewed at [[Image:B00000-01-10-0008.pdf]]
 
A detailed drawing of back plate Core can be viewed at [[Image:B00000-01-10-0008.pdf]]
Line 582: Line 612:
 
Backing sheet is the large sheet which is mounted on the downstream side of sector.  
 
Backing sheet is the large sheet which is mounted on the downstream side of sector.  
  
[[Image:assembly20_jun_14.png| 400 px]]
+
[[Image:assembly20_jun_14.png| 300 px]]
  
 
It consists of 2 parts, namely
 
It consists of 2 parts, namely
Line 596: Line 626:
 
These rods are mounted on the upstream side of each sector, connecting the left end plate aluminum casing and right end plate aluminum casing..
 
These rods are mounted on the upstream side of each sector, connecting the left end plate aluminum casing and right end plate aluminum casing..
  
[[Image:assembly20_jun_15.png| 400 px]]
+
[[Image:assembly20_jun_15.png| 300 px]]
  
 
There are 6 Carbon rods each of outer diameter of 50.8 mm and inner diameter of 48.26mm
 
There are 6 Carbon rods each of outer diameter of 50.8 mm and inner diameter of 48.26mm
Line 602: Line 632:
 
A detailed drawing of carbon fiber rods can be viewed at [[Image:B00000-01-10-0013.pdf]]
 
A detailed drawing of carbon fiber rods can be viewed at [[Image:B00000-01-10-0013.pdf]]
  
 +
 +
 +
[http://www.iac.isu.edu/mediawiki/index.php/R3#Timeline Go Back]
 +
==Second Set of Drawings==
 +
 +
These Drawings are based on the following parameters
 +
 +
1. 10mm of wire feed through is projected inward from the end plate
 +
 +
2. The Maximum diameter of the ring which would touch all the nose plate faces is 10 inches
 +
 +
3. Distance between wire planes in super layer 5 is 8.6 mm
 +
 +
4. Distance between wire planes in super layer 6 is 9 mm
 +
 +
5. Chamber tilt angle is 25 Degrees
 +
 +
6. Min Electron Scattering angle is 4.5 Degrees
 +
 +
7. Distance to the first sense wire from the target center is 4.804842 meters
 +
 +
8. Wire angles are 6 degrees with opposite slopes on the center line with reference to a horizontal in the chamber tilt plane
 +
 +
Assembly drawing of a sector [[Image:Sep25. B00000-01-10-0001.pdf]]
 +
 +
 +
 +
 +
===Nose Plate===
 +
[[Image:Sep25. B00000-01-10-0002.pdf]]
 +
 +
===Left End Plate===
 +
 +
Left End Plate assembly was drawn in 5 Drawings to complete the assembly
 +
 +
Left End Plate Assembly View: [[Image:Sep25. B00000-01-10-0003.pdf]]
 +
 +
* A sample of hole positions  are available in sheet 2
 +
 +
Left End Plate Frame: Frame has 5 sheets [[Image:Sep25. B00000-01-10-0004.pdf]]
 +
 +
* Sheet 1: Frame assembly
 +
 +
* Sheet 2: Upstream Close out
 +
 +
* Sheet 3. Downstream Close out
 +
 +
* Sheet 4. Nose side Close Out
 +
 +
* Sheet 5. back plate side Close Out
 +
 +
Left End Plate Core:  Core [[Image:Sep25. B00000-01-10-0005.pdf]]
 +
 +
Left End Plate inner skin: [[Image:Sep25. B00000-01-10-0006.pdf]]
 +
 +
Left End Plate outer skin: [[Image:Sep25. B00000-01-10-0007.pdf]]
 +
 +
===Right End Plate===
 +
 +
Right End Plate assembly was drawn in 5 Drawings to complete the assembly
 +
 +
Right End Plate Assembly View: [[Image:Sep25. B00000-01-10-0008.pdf]]
 +
 +
* A sample of hole positions  are available in sheet 2
 +
 +
Left End Plate Frame: Frame has 5 sheets [[Image:Sep25. B00000-01-10-0009.pdf]]
 +
 +
* Sheet 1: Frame assembly
 +
 +
* Sheet 2: Upstream Close out
 +
 +
* Sheet 3. Downstream Close out
 +
 +
* Sheet 4. Nose side Close Out
 +
 +
* Sheet 5. back plate side Close Out
 +
 +
Right End Plate Core:  Core [[Image:Sep25. B00000-01-10-0010.pdf]]
 +
 +
Right End Plate inner skin: [[Image:Sep25. B00000-01-10-0011.pdf]]
 +
 +
Right End Plate outer skin: [[Image:Sep25. B00000-01-10-0012.pdf]]
 +
 +
 +
 +
===Back Plate ===
 +
 +
Back Plate assembly was drawn in 5 Drawings to complete the back plate assembly
 +
 +
Back Plate Assembly View: [[Image:Sep. B00000-01-10-00013.pdf]]
 +
 +
Back Plate Frame: Frame has 5 sheets [[Image:Sep. B00000-01-10-00014.pdf]]
 +
 +
* Sheet 1: Frame assembly
 +
 +
* Sheet 2: Upstream Close out
 +
 +
* Sheet 3. Downstream Close out
 +
 +
* Sheet 4. Right Close Out
 +
 +
* Sheet 5. left Close Out
 +
 +
Back Plate Core: [[Image:Sep. B00000-01-10-00015.pdf]]
 +
 +
Back Plate inner skin: [[Image:Sep. B00000-01-10-00016.pdf]]
 +
 +
Back Plate outer skin: [[Image:Sep. B00000-01-10-00017.pdf]]
 +
 +
 +
===Hexcel Backing sheet===
 +
 +
[[Image:Sep. B00000-01-10-00018.pdf]]
 +
 +
===carbon rods===
 +
 +
[[Image:Sep. B00000-01-10-00019.pdf]]
 +
 +
===Chamber holding support plates===
 +
 +
[[Image:Sep. B00000-01-10-00020.pdf]]
  
  
 
[http://www.iac.isu.edu/mediawiki/index.php/R3#Timeline Go Back]
 
[http://www.iac.isu.edu/mediawiki/index.php/R3#Timeline Go Back]

Latest revision as of 08:48, 14 October 2008

Detailed Design Drawing Report 6/27/08

Introduction

The CLAS12 Drift chamber has 3 regions arranged as shown below

Jul17 2008 2.png Jul17 2008 1.png


The electrons scatter from the target center will travel through region 1, region 2 and region 3. All these regions look the same way. However, their sizes and the materials with which they are made are different. Due to the fact their sizes are different; some of them have some structural add-ons to support their structural abilities. The chambers are arranged in such a way that every chamber receives the same number of electrons. Apart from that, the chambers were shaped in such a way that all the electrons travel approximately the same distance before they hit a particular chamber.

Jul17 2008 3.png


Each and every chamber has 6 equal sized pieces which are shaped similar to a triangular piece. All of these pieces are arranged and bowed inward to resemble sectors in a 6 sector umbrella.As discussed before, each region will be sized different. Region 3 will be the biggest of all, as region 3 has to cover a larger electron span (surface area).

Although these pieces are termed as triangular, these are not triangular in reality. The nose which is the smallest of all is very small compared to the other plates, which will make us to visualize this as a triangular piece. Ar Co2 (90/10) gas is maintained in each of these chambers at an operating pressure of 0.001444 Psi and a peak pressure 5 times higher. In turn there are about 4928 wires (112 Sense wires with 44 Wire Layers) connected across the plates inside each piece.

Design Criteria

Initial parameters to be followed to fulfill to satisfy design Criteria


Distance from target to first sense wire plane along a ray which is normal to the end plate 4746.5 mm
Chamber Tilt Angle 25 Degrees
Maximum Scattering Angle 45.05 Degrees
Minimum Scattering Angle 4.5 Degrees
Angle of the wires to the horizontal 6 Degrees
Max end plate deflection 50 [math]\mu[/math]m


Jun20 2008 1.png Jun20 2008 2.png Jun20 2008 3.png

Introduction to Assembly

R3BreakOutDiagram.jpg

Paragraph defining all the parts

Nose Plate

Nose Plate: Assembly20 jun 1.png

Nose Plate will be made of rigid material such as solid aluminum, since the supporting mechanism will be attached to these plates. The nose plate will connect the bottoms of the two end plated and provides the interface.

End Plate

End Plate: Assembly17 jul 4.png

The End plate is about 4830 mm and 4665mm in length along the longitudinal length and about 525mm in width. It has approximately about 5000 holes with an approximate diameter of 6mm on the surface and about 9mm inside the surface. There will be two End plates names as Right End plate and Left End plate which are located to the actual right and left side of each sector when viewed from the target center respectively.


Back Plate

Back Plate: Assembly17 jul 5.png It is the plate which connects the top edges of both the end plates and holds the fixtures settings

Carbon Rods

Carbon Rods: Assembly17 jul 6.png

To provide rigidity, there will be several carbon rods fixed in between both the end plates and they vary in length depending on no.of carbon rods used and the location of rods. These rods are hollow to reduce the electron dissipation in the section.

Upstream Window and Downstream Window's

Upstream Window and Downstream Window's:Assembly17 jul 7.png

Upstream Window is the thin Mylar sheet of about 1/1000th of an inch crimped or glued on the upstream side of electron flow slightly after the carbon rods. Downstream Window is a Hexcel honeycomb material provided on the downstream side to help support the assembly, to provide rigidity and to enclose each sector

Wire pattern

The wire pattern at the center plane will be symmetric and easy to understand. The wire pattern in each super layer on this plane is same and a view at this wires at this plane will be as follows

Jun20 2008 4.png

In the horizontal direction we have 6 six sense wires. so, there will be a 2 + 6 times 3 + 2 = 22 wire planes as shown in the fig. If the distance between each wire plane is 'H' mm. Then the total span of wires in this direction will be 21H mm.

In the vertical direction, there are 112 sense wires, so there will be 1 + 1 (guard wire) + 112 (sense Wires) + 112 (Field wires) + 1 + 1 (Guard wire) = 228 wire planes as shown. If the distance between each wire plane is 'V' mm. Then, the total span in this direction will be 227V mm

H = 9 mm

V = 15.5884 mm

No. of sense wires in each super layer = ?

No. of field wires in each super layer = ?

No. of guard wires in each super layer = ?

Analysis

To determine the stability of the design, various sets of analysis were performed under different constraint and loading conditions. Sometimes each of the part was analyzed individually and also in the assembly. Some parts were analyzed for different materials

Part Analysis

These are those analysis were individual parts were analyzed under various loading and constraint conditions. Some of the constraints were assumed to understand the influence of each constraint, material and load. supportive manual calculations were also compared with these analysis in few cases.

End Plate

End plate was considered in 2D and 3D with various thicknesses and various materials, supports and constraints

Point Load Deflection

A simple back-of-the-envelope calculation for deflection was performed assuming aluminum endplates and a point-load force (representing the distributed force from the wires into a single load). The force on an endplate due only to the tension from the 4,928 wires is about 5700 N /2. A simple calculation based on the definition of Young's modulus can yield an order-of-magnitude-level estimate for the deflection of an aluminum endplate in which the wires exert a force perpendicular to the endplate. The deflection [math]y[/math] of the endplate in terms of Young's Modulus [math](Y)[/math] is given by the equation:

[math]Y \equiv \frac{F}{4wy} \left( \frac{l}{t}\right )^3[/math]

where

[math]Y = 7 \times 10^{10}N/m^2 \equiv[/math] Young's Modulus for Aluminum
[math]F = 2850 N \equiv[/math]point force/load
[math]w =0.526 m \equiv[/math] width of the endplate
[math]y \equiv[/math] deflection of endplate due to point force
[math]l =4.02 m \equiv[/math] length of the endplate
[math]t = 0.05 m \equiv[/math] thickness of the endplate

By substituting in the above values and solvign the equation, a deflection of 7 mm is expected for a 5 cm thick aluminum endplate. If a 5 cm thick stainless steel [math](Y=2.1 \times 10^{11} N/m^2 )[/math] endplate were used, the deflection would decrease from 7 mm to 2.5 mm (due to the linear dependence of the deflection on the Young's Modulus). The previous work performed by Kevin Folkman at the IAC came to a similar conclusion.

Distributed Load Deflection

The endplate deflection calculations were refined to a more realistic case in which the load is distributed evenly along the endplate. The tension of the wires on the endplate was divided into three regions; W1,W2, and W3. The load W3 corresponds to a region along the endplate in which wires from both super layers are creating a load on the endplate. Loads W1 and W2 represent regions in which only a single super layer is causing a load. The endplate is "simply" supported in order to calculate the deflection. The term "simply supported" implies that one side (left side of an endplate for this case) may rotate but not translate (resulting in two reaction forces) whereas the other side (the right side of and endplate for this case) is supported such that it may rotate and translate (resulting in a single, normal reaction force). Figure 7 labels the loads as well as distances over which the loads are applied on the end plate. A total force of 340 lbs exerted by the drift chamber wires is decomposed into its components according to the angle made by the wire on the endplate.

EndPlateDeflectionHandCalc.jpg
Label value
a 99.02 mm
b 96.22 mm
c 4025.88 mm
d 335.17 mm
e 273.88 mm
[math]W_1[/math] 0.3=1223/(C+B) N/mm
[math]W_2[/math] 0.61 N/mm
[math]W_3[/math] 0.32 =1381/(C+D)N/mm
Figure: A diagram of the loads on a simply supported end plate. The table to the right gives the load values and distances.


The following calculations are in accordance to a standard approach covered in all undergraduate "Mechanics of Materials" engineering courses. This method is based on integrating the elastic curve equation for a beam. The equation of the elastic curve relates deflection (y) to Moments (M) at given linear locations along the beam (x):


[math]\frac{d^2y}{dx^2} = \frac{M(x)}{E I_A}[/math]


where [math]E[/math] represents Young's Modulus and [math]I_A[/math] is the Area Momentum of Inertia. The Area Moment of Inertis [math](I_A)[/math] is defined as the second moment of an area about a given axis:


[math]I_{A,x} = \int x^2 dA =[/math] Area moment of inertia about the x-axis.


The mass moment of Inertia is defined as:


[math]I= \int r^2 dM = \rho I_A[/math]


In order to perform these calcuations, the following assumption were made:

  1. The end plate is made of homogenous uniform elastic material with a Young's Modulus of [math]E=210 x 10^23 N/mm^2[/math] (Stainless Steel).
  2. The horizontal component of the loading is completely neglected.
  3. The deflection in the x-direction is negligible.
  4. The end plate is rectangular in shape with a width of 526 mm and thickness of 50.8 mm resulting area moment of inertia ([math]I_A[/math]) =5746.4 [math]mm^4[/math].
  5. The loading provided by wire tensions are equivalent to a uniformly distributed load.
  6. The maximum deflection occurs along the length which is represented by [math]c[/math] in the diagram.
  7. The loading applied is under the elastic limit of the material.
  8. The effects of the endplate weight are ignored.

The moments experienced along the endplate may be divided into 5 separate equations, each equation valid only for its corresponding region:


[math]M_a = -\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot x[/math]
[math]M_b = -\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot (a+x) + \frac{W_1 \cdot x^2}{2}[/math]
[math]M_c = -\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot (a+b+x) + W_1 \cdot b \left ( \frac{b}{2} +x \right) + \frac{W_2 \cdot x^2}{2}[/math]
[math]M_d = -\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot (a+b+c+ x) + W_1 \cdot b \left ( \frac{b}{2} +c+x \right) + W_2\cdot c \left ( \frac{c}{2} + x \right) + \frac{W_3 \cdot x^2}{2}[/math]
[math]M_e = -\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot (a+b+c+d+ x) + W_1 \cdot b \left ( \frac{b}{2} +c+d+x \right) + W_2\cdot c \left ( \frac{c}{2} + d+x \right) + W_3 \cdot d \left (\frac{d}{2} +x \right)[/math]

where [math]x[/math] represents the linear distance along the endplate. If we assume that the largest magnitude of deflection occurs in region c, then we may integrate the above 2nd order elastic curve equation once and determine the critical point which represents the point of maximum deflection ( contra flexure).

[math]\int \frac{dy}{dx}dy = \frac{dy}{dx} = \int M_c dx[/math]
= [math]-\frac{W_1 \cdot b + W_2 \cdot c + W_3 \cdot d}{2} \cdot (ax+bx+x^2/2) + W_1 \cdot b \left ( \frac{bx}{2} +x^2/2 \right) + \frac{W_2 \cdot x^3}{6} +C_{integration}[/math]

where [math]C_{integration} =[/math] a constant of integration. Integrating the equation a 2nd time will result in an equation for the amount of the deflection. The constants of integration my be found by applying boundary conditions at points where the deflection is zero (at the ends or [math]x=0[/math] and [math]x=L[/math]).

Setting [math]\frac{dy}{dx}[/math] to zero and solving for x gives the linear distance corresponding to the point of maximum deflection of x = 1654.96 mm. In other words, the maximum deflection occurs 1654.96 mm from region [math]b[/math] of the endplate or [math]1654.96 + b + a = 1850.2[/math] mm from the right hand side of the endplate. Substituting the value of x above results in a maximum deflection of 2.2 mm. Note, this deflection is only slightly smaller than that found with a point load assumption and a stainless steel endplate (2.2 mm compared to 2.5 mm, respectively).

Distributed Load FEA

A Finite Element Analysis (FEA) was performed on the same stainless steel endplate design using the commercially available computer software ANSYS. For this analysis, the loading shown previously in the "Distrubuted Load" section was used. The maximum deflection observed from the FEA was 2.14 mm, as shown; this value differs from the hand calculation by only 3%. In addition to validating the FEA analysis with hand calculations, the above results also reveal the challenge of reducing the endplate deflection using stiffer materials due to an essentially linear dependence of the deflection on the Young's Modulus. The cubic dependence of the deflection on the thickness [math](t)[/math] of the endplate, however, can be used to reach the minimum endplate deflection criteria of 50 [math]\mu m[/math], in addition to the us of stiffer material. Increasing the endplate thickness, however, comes at the cost of increasing the end plate mass. As a result, composite materials were considered in order to minimize weight. The performance of these composite materials is shown in the 3-D model section of this report.

EndPlateDeflection 5cmx53cmx4m ThickStainlessSteel.jpg
Figure: ANSYS FEA results for deflection of a stainless steel endplate design for a distrubed loading.
L Angular Support framing
Jul17 2008 13.png
Figure:

To provide support for the End plate against deflection, a 90 degrees bent L Angular is supported all around the end plate. The Non scale sectional view of the same is shown below. In this model the outer frame (shown in Red) is made of Wood pulp or paper with a very low Young’s modulus of 10 x 103 N/Sq.mm & Density of 8 x 10-8 kg/Cu.mm. Whereas the material shown in Yellow will be made of Aluminum 6061 T6 with Young’s modulus of 73.1 x 103 N/Sq.mm & Density of 2.7 x 10-6 kg/Cu.mm and material shown in green will be the region with holes. For modeling purposes, this region is considered to be Aluminum 6061 with slightly lesser Density of 2.3 x 10-6 kg/Cu.mm A Load of 340 pounds is applied on each of these green strips at an angle of 55.92 & 67.92 degrees (counter wise clock direction) with the horizontal.


Jul17 2008 14.png
Figure:
Jul17 2008 15.png
Figure:
Composite End Plate

Effective Young's Modulus [math]Y_{eff}[/math]


The R3 endplates used in the CLAS 6 GeV detector were comprised of a polyurethane foam core 50.8 mm thick (2 inches) with 1.2 mm thick (0.048 inch) stainless steel sheets epoxied to each side, as shown in Figure.

EndPlateMaterialDimensions.jpg
Figure: Polyeurethane foam/stainless steel composite endplate construction and dimensions.


An effective Young's Modulus ([math]Y_{eff}[/math]) was used in the FEA model in order to simplify the model. The effective Young's Modulus for this endplate, weighted by the volume of each plate, is

[math]Y_{eff} = \frac{V_p Y_p + V_s Y_s }{V_{tot}}[/math]

where

[math]Y_p = 1.4 \times 10^8 N/m^2[/math]
[math]Y_s = 2.1 \times 10^{11} N/m^2[/math]
[math]V_p = L \times W \times 2[/math] inches
[math]V_s = L \times W \times 0.096[/math] inches


Therefore, the effective Young's Modulus was found to be:

[math]Y_{eff} = \frac{2(1.4 \times 10^8) +0.096(2.1 \times 10^{11})}{2.096} = 9.75 \times 10^{9} N/m^2[/math]
FEA Deflection Results

The effective Young's Modulus of [math]9.75 \times 10^9 N/m^2[/math] was used to determine the deflection of the endplate due to a distributed load (see Figure 3.5.2). Results indicate a maximum transverse deflection of 32.4 mm which is larger than that observed with the stainless steel material. However, when gravity is included, the composite material will deflect less due to its lower density.

DtotNoRods.jpg
Configuration X max Y max Z max D max
(mm) (mm) (mm) (mm)
No rods .67 32.4 .04 32.4
Fixing the carbon Rod locations on the end plate

In this analysis, the end plate is a straight rectangular shaped sheet. six carbon rods were assumed and the locations where the carbon rods are attached to the end plate are fixed for analysis. FR-3700 Foam with slices of steel is considered for this analysis. Effective Material properties were used wherever required. The short sided edges of the rectangular end plate is considered to be fixed pretending a cantilever beam.

Jul17 2008 8.png
Figure:
Fixing both Carbon Rod and Hexcel side edges on the end plate

Deflection Analysis of the End plate (Slices of Polyurethane and Steel) with fixed carbon rods and Hexcel foam sheet edges


A Hexcel Foam Sheet HRH 10-1/8 -1/8 is introduced in the model to reduce the deflection. This sheet is pre impregnated with thin sheets of metal on either side along the face of the end plate. The layout can be assumed as 0.010 (Skin 1) + 1.520 (Core) + 0.010 (Skin 2) inches in thickness. In this analysis the carbon rods and Hexcel foam sheet are assumed to be completely restricting the movement on the edges

Jul17 2008 9.png
Figure:

Loading conditions:

• The regions shown as material 3 and material 4 are fixed with carbon rods and Hexcel foam sheet respectively

• The areas on the side view (face attached to the nose plate and the face attached to the face (top) plate) is also constrained for movement

• Load at 6 degrees on material 2 as usual

• Gravity downwards i.e. on –y direction


Jul17 2008 10.png
Jul17 2008 11.png
Jul17 2008 12.png
Figure:

Carbon Rod Buckling

A support brace composed of carbon rods was considered in order to reduce the larger deflections of composite endplates compared to endplates made from stainless steel. These rods would be used on the front side of the R3 drift chamber and span between the two endplates. The use of 1" diameter hollow carbon fiber rods with 2 mm thick walls in the 6 GeV R3 design did not appear to appreciably impact the tracking capabilities of the drift chamber. The deflection of these carbon fiber rods was modeled as a separate part in ANSYS and compared with hand calculation.

Compression

If one makes the assumption that the rod buckles by an external force along the length of the rod, then the compression of the rod can be calculated using the definition of Young's Modulus (Y) given by the equation:

[math]Y= \frac{\frac{F}{A}}{\frac{\Delta L}{L}}[/math]

where

[math]F =[/math] Compression force exerted along the end of the rod
[math]L =[/math] length of the rod = 2.8 m for the longest rod
[math]A =[/math] cross sections area of the rod = [math]\pi (25 mm)^2[/math]
[math]\Delta L =[/math] rod compression distance = [math]50 \times 10^{-6}[/math]


The force needed to cause the carbon fiber rod to buckle such that the endplate deflects [math]50 \mu m[/math] can be estimated by assuming that the length of the rod (2.8 m) compresses by [math]50 \mu m[/math].

[math]F = \frac{YA \Delta L }{L} = \frac{1.5 \times 10^{11} N/m^2 (\pi 0.000625 m^2) 50 \times 10^{-6} m } {2.8 m}= 5259N[/math]

The total force along the whole endplate from just the drift chamber wire tension amount to less than 3000 N which is less than a factor of 2 smaller than the force needed to compress a single carbon rod used to brace the endplates. Therefore, placing at least 6 carbon rod braces in the drift chamber should provide substantial support for the endplates.

Buckling Load Threshold

The load at which a carbon fiber rod will start to buckle is given by Euler's formula (defined in any undergraduate "Mechanics of Materials" textbook). Figure 4.2.1 depicts the load configuration on the rod for this calculation.

EulersBucklingDiagramWequation.jpg
Figure: Sketch showing the definition of Euler's buckling load threshold.


[math]F_{cr}[/math] represent the critical force needed to cause the rod to begin to buckle. Young's Modulus for a carbon fiber rod is 1.5 x 10^11 N/[math]m^2[/math] and the longest rod's half length (L for the above equation) is 1.4 m. The Area Moment of inertia about the end of a hollow cylinder of inner radius[math] (R_i)[/math] and outer radius [math](R_o)[/math] can be found from:

[math]I_{A,z}= \int_{Ri}^{Ro} r^2 \pi r dr = \frac{\pi}{4} \left( Ro^4 -Ri^4\right) [/math]
[math]=\frac{\pi}{4} \left( (0.0254)^4 -(0.0244)^4\right) = 4.85 * 10^-8 m^4[/math]

The buckling force is found to be 36,646N, an order of magnitude larger than the predicted endplate forces.


The above buckling threshold calculation was performed using ANSYS. The results predicted a threshold force of 36989 N compared to the 36646 N value found from hand calculations. ANSYS also predicts that the rod will deflect almost 2 mm if the buckling load is reached, no deflection due to buckling will occur before the load level is reached.


CarbonRodBuckling AnsysCalc1.jpg
Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle.

Actual Buckling --- FEA

In the previous FEA results, both ends of the carbon rods were constrained from moving from x and y directions and does not account for the deflection of the endplates. If the endplates deflect the ends of the carbon rods will be compressed. The buckling load in this case is observed to be 54720.5N as shown below in the Figure. In the event that the buckling load is reached, ANSYS predicts a deflection of at least 11 mm will occur. It should also be noted that the buckling does not have a preferred direction making it possible for the middle of the rod to bend in any direction.

CarbonRodBuckling AnsysCalc2.jpg
Figure: FEA of the maximum (threshold) force needed to cause a carbon rod to buckle with the real constraints.

Upstream Window (Mylar) Analysis

If the mylar thickness is increase by a factor of 10 (form 1/1000 of an inch to 1/100), ANSYS would predict a deflection of about 12 mm. Formula do exist for simple geometries such as a square and a circle but not a triangle. A hand calculation for a square which is a factor of 40 smaller in size to R3 predicts 1/1000 inch thick rectangular mylar sheet will deflect about 1 mm and a circle a little less than 1 mm. If you assume the R3 triangle geometry to be similar to a 4 m x 4 m square , the mylar sheet would deflect 17.2 cm referencing manual calculations. The max error observed between manual result and ansys result was -16 percent with other sections and sizes. so expecting the deformation will be between 14.5 cm to 17.2 cm. 14.5 cm being the deflection after considering the error.


The Mylar sheet on the upstream side of the Region III drift chamber was analyzed in ANSYS for FEA deformations and the results were justified by comparing with manual calculations.

Due to the fact that the Mylar sheet is extremely thin and week for FEA analysis and has complicated geometry to perform manual calculations, the analysis is slightly simplified.

• FEA analysis approach is justified by calculating the percentage error between FEA results and Hand Calculation results for some basic shapes with the actual thickness of 0.0254mm and the young’s modulus of 3800Mpa. A square sheet of 100 x 100 mm and a circular sheet of radius 50mm.

• The thickness of the Mylar sheet is increased from 0.0254mm to 0.254mm. This is done as ANSYS has a acceptable thickness to acceptable deformation ratio, with the specified thickness of 0.0254mm, the deformation is way over the deformation limit and ANSYS cannot handle the problem.

• For Very thin sheets like mylar, Large deflection membrane stiffened analysis is proven to be accurate and the same is otherwise termed as loading with normal and membrane stress approach and is detailed, Please follow the link Deformation with both Normal and Membrane Stress approach

Mylar analysis table1.jpg

Assembly Analysis

1. The orientations and results of the primary analysis were shown at the following link Kalyan_4-25-08

2. By modeling hexcel sheet in the assembly and by replacing the rectangular constraints with circular constraints, we have considerable change in the numbers for deflection and can be observed at kalyan_16_may_08

3. The Hinge locations were moved from Upstream side to the downstream side and the results can be observed at kalyan_23_May_08

4. To reduce the max deformation, the diameter of the carbon rods and the thickness were gradually increased and the results were tabulated as follows

Deformation (mm)
Sector 1 E Max D Max X Max Y Max Z Max
3 inch Dia, 0.1 Inch thk Carbon rods 0.141 0.159 0.139 0.091 -0.073
3.5 inch Dia, 0.1 Inch thk Carbon rods 0.117 0.132 0.117 0.075 -0.050
3.5 inch Dia, 0.2 Inch thk Carbon rods 0.106 0.119 0.102 0.162 -0.053
3.5 inch Dia, 0.3 Inch thk Carbon rods 0.097 0.109 0.092 0.054 -0.048

Follow the link for images and PDF result files. The new results can be observed at kalyan_23_May_08_2.1

5. An Extra carbon rod is introduced to the geometry on the downstream side behind the hexcel sheet with various diameters and thicknesses and the results can be found at kalyan_23_May_08_2.2

6. In the next approach, the thickness of the polyurethane layer in the end plates were increased from 2 inches to 2.5 inches with carbon rods of 3.5 inch diameter and 0.5 inch thk including the single rear carbon rod.


Deformation (mm)
Sector 1 E Max D Max X Max Y Max Z Max
3.5 inch Dia, 0.5 Inch thk Carbon rods with 1 rear rod and 2.5 Inch Polyurethane on end plates 0.080 0.090 0.080 0.045 -0.031

Follow the link for images and PDF result files. The new results can be observed at kalyan_23_May_08_2.3

7. The aluminum casing width is increased by 30 mm, This increase is made on the upstream side between the aluminum slits and upstream side hole area, Triangular constraint areas were introduced to the geometry and the constraints were applied on them.

Sector 1 is studied under 6 cases of analysis.

  • Case 1: Triangular Constraints are only in the downstream side and only upstream side on the nose plate
  • Case 3: Triangular Constraints are only in the upstream side and only upstream side on the nose plate
  • Case 5: Triangular Constraints are in both upstream and downstream side and only upstream side on the nose plate
  • Case 2, Case 4, Case 6: are with both upstream and downstream side constraints on the nose plate for case 1, 3, 5 respectively

For Details, Follow the link for images and PDF result files. The new results can be observed at kalyan_30_May_08

Drawings

First set of drawings

List of drawings

S. No Drawing No Description Link
1 B00000-01-10-0001 Basic sector assembly File:B00000-01-10-0001.pdf
2 B00000-01-10-0002 Detailed drawing of Nose plate File:B00000-01-10-0002.pdf
3 B00000-01-10-0003 Detailed drawing of right end plate Core File:B00000-01-10-0003.pdf
4 B00000-01-10-0004 Detailed drawing of right end plate skin File:B00000-01-10-0004.pdf
5 B00000-01-10-0005 Detailed drawing of End plate casing File:B00000-01-10-0005.pdf
6 B00000-01-10-0006 Detailed drawing of Left end plate Core File:B00000-01-10-0006.pdf
7 B00000-01-10-0007 Detailed drawing of Left end plate skin File:B00000-01-10-0007.pdf
8 B00000-01-10-0008 Detailed drawing of back plate Core File:B00000-01-10-0008.pdf
9 B00000-01-10-0009 Detailed drawing of back plate skin File:B00000-01-10-0009.pdf
10 B00000-01-10-0010 Detailed drawing of back plate casing File:B00000-01-10-0010.pdf
11 B00000-01-10-0011 Detailed drawing of back plate Core File:B00000-01-10-0011.pdf
12 B00000-01-10-0012 Detailed drawing of back plate skin File:B00000-01-10-0012.pdf
13 B00000-01-10-0013 Detailed drawing of carbon fiber rods File:B00000-01-10-0013.pdf


The Assembly of each sector in the region 3 drift chamber can be considered similar to each other. Each assembly can be divided into sub-assemblies like

1. Nose Plate

2. Right End Plate

3. Left End plate

4. Back plate

5. Backing Sheet

6. Carbon rods

7. Attachments: These are the external geometric parts of each sector, used for clamping and mounting each sector. so, they might change with the orientation of each sector

A detailed drawing of this Basic sector assembly can be viewed at File:B00000-01-10-0001.pdf


Nose Plate

Nose plate is the plate where both the end plates are attached to it on either side

Assembly20 jun 1.png

A detailed drawing of Nose plate can be viewed at File:B00000-01-10-0002.pdf

Right end plate

Left end plate is the end plate to the left hand side if we are viewing from the target.

Assembly20 jun 2.png

They can be referenced with left and right to show each sub assembly.

A detailed drawing of right end plate Core can be viewed at File:B00000-01-10-0003.pdf

A detailed drawing of right end plate skin can be viewed at File:B00000-01-10-0004.pdf

Since end plate casing will not have holes for wires, the drawing for left end plate casing and right end plate casing will be the same.

A detailed drawing of End plate casing can be viewed at File:B00000-01-10-0005.pdf

Left End Plate

Left end plate is the end plate to the left hand side if we are viewing from the target. Left end plate and the right end plate are same with parts and its dimensions. However, the hole locations differ between each other.

Assembly20 jun 2.png

Each end plate sub assembly consists of 3 parts, namely

End plate casing - Made of Aluminum.

Assembly20 jun 5.png


They can be referenced with left and right to show each sub assembly.

A detailed drawing of Left end plate Core can be viewed at File:B00000-01-10-0006.pdf

A detailed drawing of Left end plate skin can be viewed at File:B00000-01-10-0007.pdf

Back Plate

Back plate is the plate which connects the left end plate and right end plate on the top.

Assembly20 jun 10.png

Back plate sub assembly consists of 3 parts, namely

Back plate Core - made of Polyurethane

Assembly20 jun 11.png

Back plate Skins - 2 No's- Made of stainless steel

Assembly20 jun 12.png

Back plate casing - Made of Aluminum

Assembly20 jun 13.png

A detailed drawing of back plate Core can be viewed at File:B00000-01-10-0008.pdf

A detailed drawing of back plate skin can be viewed at File:B00000-01-10-0009.pdf

A detailed drawing of back plate casing can be viewed at File:B00000-01-10-0010.pdf

Backing Sheet

Backing sheet is the large sheet which is mounted on the downstream side of sector.

Assembly20 jun 14.png

It consists of 2 parts, namely

Hexcel Core and Carbon fiber skins on either side

A detailed drawing of back plate Core can be viewed at File:B00000-01-10-0011.pdf

A detailed drawing of back plate skin can be viewed at File:B00000-01-10-0012.pdf

Carbon fiber rods

These rods are mounted on the upstream side of each sector, connecting the left end plate aluminum casing and right end plate aluminum casing..

Assembly20 jun 15.png

There are 6 Carbon rods each of outer diameter of 50.8 mm and inner diameter of 48.26mm

A detailed drawing of carbon fiber rods can be viewed at File:B00000-01-10-0013.pdf


Go Back

Second Set of Drawings

These Drawings are based on the following parameters

1. 10mm of wire feed through is projected inward from the end plate

2. The Maximum diameter of the ring which would touch all the nose plate faces is 10 inches

3. Distance between wire planes in super layer 5 is 8.6 mm

4. Distance between wire planes in super layer 6 is 9 mm

5. Chamber tilt angle is 25 Degrees

6. Min Electron Scattering angle is 4.5 Degrees

7. Distance to the first sense wire from the target center is 4.804842 meters

8. Wire angles are 6 degrees with opposite slopes on the center line with reference to a horizontal in the chamber tilt plane

Assembly drawing of a sector File:Sep25. B00000-01-10-0001.pdf



Nose Plate

File:Sep25. B00000-01-10-0002.pdf

Left End Plate

Left End Plate assembly was drawn in 5 Drawings to complete the assembly

Left End Plate Assembly View: File:Sep25. B00000-01-10-0003.pdf

  • A sample of hole positions are available in sheet 2

Left End Plate Frame: Frame has 5 sheets File:Sep25. B00000-01-10-0004.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Nose side Close Out
  • Sheet 5. back plate side Close Out

Left End Plate Core: Core File:Sep25. B00000-01-10-0005.pdf

Left End Plate inner skin: File:Sep25. B00000-01-10-0006.pdf

Left End Plate outer skin: File:Sep25. B00000-01-10-0007.pdf

Right End Plate

Right End Plate assembly was drawn in 5 Drawings to complete the assembly

Right End Plate Assembly View: File:Sep25. B00000-01-10-0008.pdf

  • A sample of hole positions are available in sheet 2

Left End Plate Frame: Frame has 5 sheets File:Sep25. B00000-01-10-0009.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Nose side Close Out
  • Sheet 5. back plate side Close Out

Right End Plate Core: Core File:Sep25. B00000-01-10-0010.pdf

Right End Plate inner skin: File:Sep25. B00000-01-10-0011.pdf

Right End Plate outer skin: File:Sep25. B00000-01-10-0012.pdf


Back Plate

Back Plate assembly was drawn in 5 Drawings to complete the back plate assembly

Back Plate Assembly View: File:Sep. B00000-01-10-00013.pdf

Back Plate Frame: Frame has 5 sheets File:Sep. B00000-01-10-00014.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Right Close Out
  • Sheet 5. left Close Out

Back Plate Core: File:Sep. B00000-01-10-00015.pdf

Back Plate inner skin: File:Sep. B00000-01-10-00016.pdf

Back Plate outer skin: File:Sep. B00000-01-10-00017.pdf


Hexcel Backing sheet

File:Sep. B00000-01-10-00018.pdf

carbon rods

File:Sep. B00000-01-10-00019.pdf

Chamber holding support plates

File:Sep. B00000-01-10-00020.pdf


Go Back