Difference between revisions of "PositronTargetWorkByChrissJackson"
(→ports) |
|||
| (15 intermediate revisions by 2 users not shown) | |||
| Line 50: | Line 50: | ||
| − | + | ==ports== | |
| + | |||
| + | {| border="1" |cellpadding="20" cellspacing="0 | ||
| + | |- | ||
| + | | Parts || Quantity || Items connecting to Target Chamber | ||
| + | |- | ||
| + | | 10 - pin wiring feedthrough || 1 || [http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=9132004 Feedthrough] | ||
| + | |- | ||
| + | | cooling lines || 2 || [http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=611005 Cooling Hoses] | ||
| + | |- | ||
| + | | IR optical window || 2 || [http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=9712007 Optical Window] | ||
| + | |- | ||
| + | | Beam line || 2 || [http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=100021 Flange] | ||
| + | |- | ||
| + | | Ion Pump || 1 || [http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=100021 Flange] | ||
| + | |- | ||
| + | | Roughing Pump || 1 || | ||
| + | |} | ||
| + | |||
| + | |||
| + | |||
| + | 1.) Lid with a lip that bolts on. | ||
| + | |||
| + | 2.) bolt pattern on the bottom for the motor mounts | ||
| + | |||
| + | 3.) find cooling lines for inside the box | ||
| + | |||
| + | 4.) Find elbows for the rotary unions. | ||
| + | |||
| + | . | ||
| + | . | ||
| + | . | ||
| + | . | ||
| + | 100.) Design a target mounting system | ||
=Equipment= | =Equipment= | ||
| Line 70: | Line 103: | ||
C: 4.25 | C: 4.25 | ||
D: 4.63 | D: 4.63 | ||
| + | |||
| + | http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=611005 | ||
=Performance tests= | =Performance tests= | ||
Latest revision as of 17:59, 15 May 2012
- Chriss Jackson's Positron Target development logbook
- Goal
- Construct a Tungsten target and vacuum enclosure to be used for generating positrons using an incident electron beam.
Geometry
Tungsten Disks
- Dimensions are in cm
http://www.alibaba.com/product-gs/346924116/Tungsten_Disk_With_Screw.html
http://www.zlxtech.com.cn/products.asp?productcode=7401000404
http://www.cleveland-tungsten.com/
If the motor has a radius of 2.5" and I want to shield the motor from the beam using 2" of Pb and the beam is about 1" in diameter then I want a Tungsten disk that is
5.21" in radius = 13.25 cm in radius ~ 30 cm in diameter
Target Chamber design
Latest Design From empire and Sadiq's measurement of the available space
 |
 |
 |
|
| Target motor Design | Available beam line space | Motor axle coupling to rotary union | Hub and spline to attache targets |
Dimensions for the target chamber box. Measurements in inches. updated 11 May 2012. Holes for tubing still missing, need to measure.
 |
 |
 |
|
| Bottom view | Front View | Left View | Isometric View |
ports
| Parts | Quantity | Items connecting to Target Chamber |
| 10 - pin wiring feedthrough | 1 | Feedthrough |
| cooling lines | 2 | Cooling Hoses |
| IR optical window | 2 | Optical Window |
| Beam line | 2 | Flange |
| Ion Pump | 1 | Flange |
| Roughing Pump | 1 |
1.) Lid with a lip that bolts on.
2.) bolt pattern on the bottom for the motor mounts
3.) find cooling lines for inside the box
4.) Find elbows for the rotary unions.
. . . . 100.) Design a target mounting system
Equipment
Motor
Controller
Vacuum Chamber
Feedthroughs
A: 5.88 B: 3.00 C: 4.25 D: 4.63
http://www.mdcvacuum.com/DisplayPart.aspx?d=MDC&p=611005