Difference between revisions of "Lab 9 TF EIM"
Jump to navigation
Jump to search
| (18 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
=Clipping Circuit= | =Clipping Circuit= | ||
| − | + | 1.) Construct the circuit shown below using a silicon diode. | |
| − | + | ||
| − | + | [[File:TF_EIM_Lab9.png | 200 px]] | |
| − | + | ||
| + | 2.) Use a sine wave generator to drive the circuit so <math>V_{in} = V_0 \cos(2 \pi \nu t)</math> where <math>V_0 = 0.1</math> V and <math> \nu</math> = 1kHz. (20 pnts) | ||
| + | |||
| + | 3.)Based on your observations using a oscilloscope, sketch the voltages <math>V_{in}</math> and <math>V_{out}</math> as a function of time. | ||
| + | |||
| + | 4.)Do another sketch for<math> V_0</math> = 1.0 V and another for 10.0 V (DONT LET ANY SMOKE OUT!). (20 pnts) | ||
= Differentiating Circuit with clipping= | = Differentiating Circuit with clipping= | ||
#Construct the circuit below. | #Construct the circuit below. | ||
| − | #Select <math>R_1</math> and <math>R_2</math> such that the current from the +5V DC source is 1.0 mA and the DC voltage at <math> | + | [[File:TF_EIM_Lab9a.png | 200 px]] |
| − | #Select a capacitor <math>( | + | #Select <math>R_1</math> and <math>R_2</math> such that the current from the +5V DC source is less than 1.0 mA and the DC voltage at <math>V_{out}</math> is 3 V when there is no input pulse. |
| − | #plot <math> | + | #Select a capacitor <math>(C)</math>and a pulse width <math>\tau</math> to form a differentiating circuit for the pulse from the signal generator. Hint: <math>R_{12}C \ll \tau</math>. |
| − | # Now add the diode circuit from part 1 to prevent | + | #plot <math>V_{in}</math> and <math>V_{out}</math> as a function of time using your scope observations. (20 pnts) |
| − | #plot <math> | + | # Now add the diode circuit from part 1 to prevent <math>V_{out}</math> from rising above +5 V. Sketch the new circuit below. |
| + | #plot <math>V_{in}</math> and <math>V_{out}</math> as a function of time with the diode circuit you added using your scope observations. (the diode should clip off positive spikes)(20 pnts) | ||
=Questions= | =Questions= | ||
| − | #Explain your results in parts 1 & 2 in terms of the diode turn-on voltage. | + | #Explain your results in parts 1 & 2 in terms of the diode turn-on voltage. (20 pnts) |
[[Forest_Electronic_Instrumentation_and_Measurement]] | [[Forest_Electronic_Instrumentation_and_Measurement]] | ||
Latest revision as of 02:55, 23 February 2011
Lab 9: Diode Circuits
Clipping Circuit
1.) Construct the circuit shown below using a silicon diode.
2.) Use a sine wave generator to drive the circuit so where V and = 1kHz. (20 pnts)
3.)Based on your observations using a oscilloscope, sketch the voltages and as a function of time.
4.)Do another sketch for = 1.0 V and another for 10.0 V (DONT LET ANY SMOKE OUT!). (20 pnts)
Differentiating Circuit with clipping
- Construct the circuit below.
- Select and such that the current from the +5V DC source is less than 1.0 mA and the DC voltage at is 3 V when there is no input pulse.
- Select a capacitor and a pulse width to form a differentiating circuit for the pulse from the signal generator. Hint: .
- plot and as a function of time using your scope observations. (20 pnts)
- Now add the diode circuit from part 1 to prevent from rising above +5 V. Sketch the new circuit below.
- plot and as a function of time with the diode circuit you added using your scope observations. (the diode should clip off positive spikes)(20 pnts)
Questions
- Explain your results in parts 1 & 2 in terms of the diode turn-on voltage. (20 pnts)