Difference between revisions of "HV-Circuit For TGEM-Detector"
Jump to navigation
Jump to search
| (8 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=HV-Circuit Design= | =HV-Circuit Design= | ||
| + | |||
| + | Remove RC Trigout circuit from 2nd TGEM stage | ||
| + | |||
The HV- circuit for TGEM consists of two boards represented by the following schemes: | The HV- circuit for TGEM consists of two boards represented by the following schemes: | ||
| + | {| border="1" cellpadding="4" | ||
| + | |- | ||
| + | | [[Image: TGEM_1_2.png | 250 px|thumb|circuit 1]]||[[Image: TGEM_3.png | 250 px|thumb|circuit 2]] | ||
| + | |} | ||
| − | [[Image: | + | There are 10 cm X 8 cm boards, the 2nd board are deductible in size a little(instead of 8cm in width, it may reach 5cm), the following represent both of them with all the layers : |
| + | {| border="1" cellpadding="4" | ||
| + | |- | ||
| + | |[[Image: TGEM_1_2_D.png | 250 px|thumb|board 1]]|| [[Image: TGEM_3_D.png | 250 px|thumb|board 2]] | ||
| + | |} | ||
| − | [[Image: | + | Boards top layer: |
| + | {| border="1" cellpadding="4" | ||
| + | |- | ||
| + | |[[Image: TGEM_1_2_t.png | 250 px|thumb|board 1]]|| [[Image: TGEM_3_t.png | 250 px|thumb|board 2]] | ||
| + | |} | ||
| − | + | Boards bottom layer: | |
| + | {| border="1" cellpadding="4" | ||
| + | |- | ||
| + | |[[Image: TGEM_1_2_b.png | 250 px|thumb|board 1]]|| [[Image: TGEM_3_b.png | 250 px|thumb|board 2]] | ||
| + | |} | ||
| − | |||
There is a little difference between the these schemes and the old ones that I added the filter for each board. | There is a little difference between the these schemes and the old ones that I added the filter for each board. | ||
| − | + | ||
| + | The location of the boards on the chamber: | ||
| + | |||
| + | After removing filter, print out another picture, place resistor in the paper and take another picture. | ||
| + | |||
| + | [[Image: HV_location.png | 250 px]] | ||
| + | |||
| + | |||
| + | |||
| + | [http://wiki.iac.isu.edu/index.php/Neutron_TGEM_Detector_Abdel#01.2F06.2F10_.28HV-circuit_Design.29 Go Back] | ||
Latest revision as of 20:56, 2 June 2010
HV-Circuit Design
Remove RC Trigout circuit from 2nd TGEM stage
The HV- circuit for TGEM consists of two boards represented by the following schemes:
There are 10 cm X 8 cm boards, the 2nd board are deductible in size a little(instead of 8cm in width, it may reach 5cm), the following represent both of them with all the layers :
Boards top layer:
Boards bottom layer:
There is a little difference between the these schemes and the old ones that I added the filter for each board.
The location of the boards on the chamber:
After removing filter, print out another picture, place resistor in the paper and take another picture.
