Difference between revisions of "Kalyan 30 May 08"
(→Case 1) |
(→Case 1) |
||
(11 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | Table of results | ||
+ | {| align="center" border="1" | ||
+ | |- | ||
+ | | || ||Deformation (mm) | ||
+ | |- | ||
+ | | Sector 1 || Constraint ||Left E Max ||Left Relative E Max ||Right E Max ||Right Relative E Max || D Max || X Max || Y Max || Z Max | ||
+ | |- | ||
+ | | Case 1 ||Downstream triangle with Upstream on Nose||0.057 ||0.053 ||0.061 || 0.032 || 0.065 || 0.053 || -0.065|| -0.030 || | ||
+ | |- | ||
+ | | Case 2 ||Downstream triangle with both sides on Nose||0.018 || 0.012||0.038 || 0.035 || 0.038 || 0.038 || -0.021|| -0.018 || | ||
+ | |- | ||
+ | | case 3 ||Upstream triangle with Upstream on Nose||0.099 ||0.093 ||0.105 || 0.092 || 0.135 || 0.111 || -0.110 || -0.093|| | ||
+ | |- | ||
+ | | case 4 ||Upstream triangle with both sides on Nose||0.103 || 0.064|| 0.117|| 0.053 || 0.129 || 0.109 || 0.119 ||-0.090|| | ||
+ | |- | ||
+ | | Case 5 ||Both side triangles with Upstream on Nose|| 0.058||0.054 || 0.065|| 0.031 || 0.065 || 0.051 || -0.065 ||-0.027|| | ||
+ | |- | ||
+ | | Case 6 ||Both side triangles with both sides on Nose||0.019 || 0.015|| 0.034|| 0.031 || 0.034 || 0.034 || -0.020 ||-0.015|| | ||
+ | |} | ||
+ | |||
=Case 1= | =Case 1= | ||
The constraints are as follows | The constraints are as follows | ||
Line 22: | Line 42: | ||
The Triangular sections are only constrained on the downstream side and the nose plate is constrained on both sides | The Triangular sections are only constrained on the downstream side and the nose plate is constrained on both sides | ||
+ | The report generated by ANSYS is available: [[Image:case2_slice1.pdf]] | ||
+ | |||
+ | |||
+ | {| align="center" | ||
+ | |- | ||
+ | |[[Image:case2_slice1left_1d.png| 450 px]]||[[Image:case2_slice1_1d.png| 500 px]]||[[Image:case2_slice1right_1d.png| 450 px]] | ||
+ | |} | ||
+ | |||
+ | {| | ||
+ | |[[Image:case2_slice1_1x.png| 410 px]]||[[Image:case2_slice1_1y.png| 410 px]]||[[Image:case2_slice1_1z.png| 410 px]] | ||
+ | |||
+ | |} | ||
+ | |||
+ | Figure 2: Images of Deflection for Sector 1 with case 2 constraints in D,X,Y,Z Directions respectively | ||
=Case 3= | =Case 3= | ||
Line 27: | Line 61: | ||
The Triangular sections are only constrained on the upstream side and the nose plate is constrained on the upstream side | The Triangular sections are only constrained on the upstream side and the nose plate is constrained on the upstream side | ||
+ | The report generated by ANSYS is available: [[Image:case3_slice1.pdf]] | ||
+ | |||
+ | |||
+ | {| align="center" | ||
+ | |- | ||
+ | |[[Image:case3_slice1left_1d.png| 450 px]]||[[Image:case3_slice1_1d.png| 500 px]]||[[Image:case3_slice1right_1d.png| 450 px]] | ||
+ | |} | ||
+ | |||
+ | {| | ||
+ | |[[Image:case3_slice1_1x.png| 410 px]]||[[Image:case3_slice1_1y.png| 410 px]]||[[Image:case3_slice1_1z.png| 410 px]] | ||
+ | |||
+ | |} | ||
+ | |||
+ | Figure 3: Images of Deflection for Sector 1 with case 3 constraints in D,X,Y,Z Directions respectively | ||
=Case 4= | =Case 4= | ||
The constraints are as follows | The constraints are as follows | ||
The Triangular sections are only constrained on the upstream side and the nose plate is constrained on both sides | The Triangular sections are only constrained on the upstream side and the nose plate is constrained on both sides | ||
+ | |||
+ | The report generated by ANSYS is available: [[Image:case4_slice1.pdf]] | ||
+ | |||
+ | {| align="center" | ||
+ | |- | ||
+ | |[[Image:case4_slice1left_1d.png| 450 px]]||[[Image:case4_slice1_1d.png| 500 px]]||[[Image:case4_slice1right_1d.png| 450 px]] | ||
+ | |} | ||
+ | |||
+ | {| | ||
+ | |[[Image:case4_slice1_1x.png| 410 px]]||[[Image:case4_slice1_1y.png| 410 px]]||[[Image:case4_slice1_1z.png| 410 px]] | ||
+ | |||
+ | |} | ||
+ | |||
+ | Figure 4: Images of Deflection for Sector 1 with case 4 constraints in D,X,Y,Z Directions respectively | ||
=Case 5= | =Case 5= | ||
Line 37: | Line 99: | ||
The Triangular sections are only constrained on both sides and the nose plate is constrained on the upstream side | The Triangular sections are only constrained on both sides and the nose plate is constrained on the upstream side | ||
+ | The report generated by ANSYS is available: [[Image:case5_slice1.pdf]] | ||
+ | |||
+ | |||
+ | {| align="center" | ||
+ | |- | ||
+ | |[[Image:case5_slice1left_1d.png| 450 px]]||[[Image:case5_slice1_1d.png| 500 px]]||[[Image:case5_slice1right_1d.png| 450 px]] | ||
+ | |} | ||
+ | |||
+ | {| | ||
+ | |[[Image:case5_slice1_1x.png| 410 px]]||[[Image:case5_slice1_1y.png| 410 px]]||[[Image:case5_slice1_1z.png| 410 px]] | ||
+ | |||
+ | |} | ||
+ | |||
+ | Figure 5: Images of Deflection for Sector 1 with case 5 constraints in D,X,Y,Z Directions respectively | ||
=Case 6= | =Case 6= | ||
The constraints are as follows | The constraints are as follows | ||
The Triangular sections and the nose plate are constrained on both sides | The Triangular sections and the nose plate are constrained on both sides | ||
+ | |||
+ | The report generated by ANSYS is available: [[Image:case6_slice1.pdf]] | ||
+ | |||
+ | |||
+ | {| align="center" | ||
+ | |- | ||
+ | |[[Image:case6_slice1left_1d.png| 450 px]]||[[Image:case6_slice1_1d.png| 500 px]]||[[Image:case6_slice1right_1d.png| 450 px]] | ||
+ | |} | ||
+ | |||
+ | {| | ||
+ | |[[Image:case6_slice1_1x.png| 410 px]]||[[Image:case6_slice1_1y.png| 410 px]]||[[Image:case6_slice1_1z.png| 410 px]] | ||
+ | |||
+ | |} | ||
+ | |||
+ | Figure 6: Images of Deflection for Sector 1 with case 6 constraints in D,X,Y,Z Directions respectively | ||
+ | |||
+ | |||
Latest revision as of 05:50, 30 May 2008
Table of results
Deformation (mm) | ||||||||||
Sector 1 | Constraint | Left E Max | Left Relative E Max | Right E Max | Right Relative E Max | D Max | X Max | Y Max | Z Max | |
Case 1 | Downstream triangle with Upstream on Nose | 0.057 | 0.053 | 0.061 | 0.032 | 0.065 | 0.053 | -0.065 | -0.030 | |
Case 2 | Downstream triangle with both sides on Nose | 0.018 | 0.012 | 0.038 | 0.035 | 0.038 | 0.038 | -0.021 | -0.018 | |
case 3 | Upstream triangle with Upstream on Nose | 0.099 | 0.093 | 0.105 | 0.092 | 0.135 | 0.111 | -0.110 | -0.093 | |
case 4 | Upstream triangle with both sides on Nose | 0.103 | 0.064 | 0.117 | 0.053 | 0.129 | 0.109 | 0.119 | -0.090 | |
Case 5 | Both side triangles with Upstream on Nose | 0.058 | 0.054 | 0.065 | 0.031 | 0.065 | 0.051 | -0.065 | -0.027 | |
Case 6 | Both side triangles with both sides on Nose | 0.019 | 0.015 | 0.034 | 0.031 | 0.034 | 0.034 | -0.020 | -0.015 |
Case 1
The constraints are as follows The Triangular sections are only constrained on the downstream side and the nose plate is constrained on the upstream side
The report generated by ANSYS is available: File:Case1 slice1.pdf
Figure 1: Images of Deflection for Sector 1 with case 1 constraints in D,X,Y,Z Directions respectively
Case 2
The constraints are as follows The Triangular sections are only constrained on the downstream side and the nose plate is constrained on both sides
The report generated by ANSYS is available: File:Case2 slice1.pdf
Figure 2: Images of Deflection for Sector 1 with case 2 constraints in D,X,Y,Z Directions respectively
Case 3
The constraints are as follows The Triangular sections are only constrained on the upstream side and the nose plate is constrained on the upstream side
The report generated by ANSYS is available: File:Case3 slice1.pdf
Figure 3: Images of Deflection for Sector 1 with case 3 constraints in D,X,Y,Z Directions respectively
Case 4
The constraints are as follows The Triangular sections are only constrained on the upstream side and the nose plate is constrained on both sides
The report generated by ANSYS is available: File:Case4 slice1.pdf
Figure 4: Images of Deflection for Sector 1 with case 4 constraints in D,X,Y,Z Directions respectively
Case 5
The constraints are as follows The Triangular sections are only constrained on both sides and the nose plate is constrained on the upstream side
The report generated by ANSYS is available: File:Case5 slice1.pdf
Figure 5: Images of Deflection for Sector 1 with case 5 constraints in D,X,Y,Z Directions respectively
Case 6
The constraints are as follows The Triangular sections and the nose plate are constrained on both sides
The report generated by ANSYS is available: File:Case6 slice1.pdf
Figure 6: Images of Deflection for Sector 1 with case 6 constraints in D,X,Y,Z Directions respectively