Difference between revisions of "Paste painting procedure"

From New IAC Wiki
Jump to navigation Jump to search
 
(88 intermediate revisions by one other user not shown)
Line 1: Line 1:
−
=Safety Conditions=
+
=Purpose=
−
Before open the paste please read SDS [[File:ED7100_OSHA_MSDS.pdf]] for the paste. Be sure that the following are available:
+
 
 +
This document description the application proceedures to safely apply the ED-7100 carbon paste.
 +
[[File:ED7100_Series_paste.pdf]]
 +
 
 +
=Requirements for safe handling=
 +
Before opening the paste please read  the ED-7100 Safety Data Sheet located at
 +
 
 +
:http://wiki.iac.isu.edu/index.php/File:ED7100_OSHA_MSDS.pdf
 +
 
 +
Be sure that the following are available:
  
 
;Ventilation:
 
;Ventilation:
−
Working with paste is highly recommended under a good ventilation area, the hood is a good environment for work.
+
An externally venting fume hood is recommended when working with this paste or a work area with very good ventilation.
  
 
;Poor Ventilation area:
 
;Poor Ventilation area:
 
Wear a well fitted NIOSH approved or industrial type canister mask.
 
Wear a well fitted NIOSH approved or industrial type canister mask.
  
−
;Paste Splashing:
+
:http://www1.mscdirect.com/CGI/NNSRIT?PMPXNO=1651332&PMT4NO=0
  
−
1- Gloves,goggles.
+
:http://www1.mscdirect.com/Disposable-Respirators-And-Masks/Respiratory-Protection/Safety/s0000002069.HTML
−
 
−
2- suitable protection clothes.
 
  
−
3- sack of sand or absorber for cleaning the area.
 
  
−
=Technical procedure=
+
;The following are required for applying the paste:
−
; Aim:  
 
−
ED7100 paste thickness effect on the electrical resistance of copper based material.
 
  
−
; a- Look at the safety conditions before using the paste.
+
# Gloves,goggles.
 +
#suitable protection clothes.
 +
# sack of sand or absorber for cleaning the area.
 +
 
 +
=Paste Application Procedure=
 +
; a- Review the "Requirements for Safe Handling" section preceding this one before using the paste.[http://wiki.iac.isu.edu/index.php/Paste_painting_procedure#Requirements_for_safe_handling]
  
 
; b- Equipment And Tools:
 
; b- Equipment And Tools:
−
55 to 77T polyester mesh, 200 mesh stainless steel screen, ER7 reducer, SW100, Oven, Multimeter, different shapes of Copper ( mainly 10X10 plate, wires), power supply, A pair of scissors, pliers, micrometer.
+
#ED-7100 paste
−
 
+
# isobutanol for cleaning,
−
; c- Before Processing Measurements:
+
#CLR A/F lens blue frame revolution dust goggles
−
 
+
#27"WD 36"L vinyl clear ansell chem-resist apron
−
Measure the values of the resistors of each copper shape (if possible)using the multimeter or the multimeter and the power supply. 
+
#35"WD 45"L neoprene Black ansell chem-resist apron
−
 
+
#8511 N90 3M particulate respirator
−
; d- Paste Processing:
+
#Nitrile disposal gloves
−
1- Printing the paste using 55 to 77T polyester mesh. For tight resistances tolerance use 200 mesh stainless steel screen to reduce the distortion. try to get a uniform surface.
+
 
−
 
 
−
2- Clean the screen and stencil of the paste residues using SW100
 
  
−
3-Let the paste dry, recommended drying conditions are in the table below:
+
; d- Application steps:
  
−
4- Curing for 1 - 2h 30min. at 150 - 165 degrees Celsius.(Contact the company for IR-curing)  
+
#put on mask and apron (use goggles if spraying paste using printer)
−
+
#establish a work area under the ventilatin hood in the Laboratory for Detector Science#Add the paste to copper plate.(using a brush or a semi-mechanical printer)
−
; After Processing Measurements:
+
#mix paste (if reducing is needed) under the hood for sufficient ventilation
−
Measure the resistors again after processing and summarize the result in table or figure.
+
#use applicator to smear paste on pc-board
 +
#Clean the paste residues using isobutanol cleaner.
 +
# Cure for 1 - 2h 30min. at 150 - 165 degrees Celsius.(Contact the company for IR-curing)
  
  
−
[[Neutron_TGEM_Detector_Abdel#7.2F31.2F2009]]
+
Back to the main page [http://wiki.iac.isu.edu/index.php/Neutron_TGEM_Detector_Abdel#10.2F27.2F09_.28Paste_painting_procedure.29]

Latest revision as of 15:55, 5 March 2012

Purpose

This document description the application proceedures to safely apply the ED-7100 carbon paste. File:ED7100 Series paste.pdf

Requirements for safe handling

Before opening the paste please read the ED-7100 Safety Data Sheet located at

http://wiki.iac.isu.edu/index.php/File:ED7100_OSHA_MSDS.pdf

Be sure that the following are available:

Ventilation

An externally venting fume hood is recommended when working with this paste or a work area with very good ventilation.

Poor Ventilation area

Wear a well fitted NIOSH approved or industrial type canister mask.

http://www1.mscdirect.com/CGI/NNSRIT?PMPXNO=1651332&PMT4NO=0
http://www1.mscdirect.com/Disposable-Respirators-And-Masks/Respiratory-Protection/Safety/s0000002069.HTML


The following are required for applying the paste
  1. Gloves,goggles.
  2. suitable protection clothes.
  3. sack of sand or absorber for cleaning the area.

Paste Application Procedure

a- Review the "Requirements for Safe Handling" section preceding this one before using the paste.[1]
b- Equipment And Tools
  1. ED-7100 paste
  2. isobutanol for cleaning,
  3. CLR A/F lens blue frame revolution dust goggles
  4. 27"WD 36"L vinyl clear ansell chem-resist apron
  5. 35"WD 45"L neoprene Black ansell chem-resist apron
  6. 8511 N90 3M particulate respirator
  7. Nitrile disposal gloves


d- Application steps
  1. put on mask and apron (use goggles if spraying paste using printer)
  2. establish a work area under the ventilatin hood in the Laboratory for Detector Science#Add the paste to copper plate.(using a brush or a semi-mechanical printer)
  3. mix paste (if reducing is needed) under the hood for sufficient ventilation
  4. use applicator to smear paste on pc-board
  5. Clean the paste residues using isobutanol cleaner.
  6. Cure for 1 - 2h 30min. at 150 - 165 degrees Celsius.(Contact the company for IR-curing)


Back to the main page [2]

Retrieved from "https://wiki.iac.isu.edu/index.php?title=Paste_painting_procedure&oldid=71752"