Difference between revisions of "Beamline Parts"

From New IAC Wiki
Jump to navigation Jump to search
Line 81: Line 81:
 
=== PR-0048 ===
 
=== PR-0048 ===
  
PR-0048: [http://www.duniway.com/images/pdf/pg/manual-r-PR-48.pdf]
+
website: [http://www.duniway.com/html/cs-ip-section-doc-link.htm]
 +
 
 +
Manual [http://www.duniway.com/images/pdf/pg/manual-r-PR-48.pdf]
 +
 
 +
Price: $810.00
 +
 
  
  
 
=== 924-0048 ===
 
=== 924-0048 ===
  
[http://www.idoism.com/2011/05/02/varian-924-0048-pressure-sensitive-relay-115-volts/]
+
 
 +
Website: [http://www.srcsurplus.com/storefrontprofiles/DeluxeSFItemDetail.aspx?sid=1&sfid=180197&c=174047&i=251105002]
 +
 
 +
Price: $745.50
  
 
=Gun=
 
=Gun=

Revision as of 21:22, 18 May 2011

Mini UHV gate valve

Valve with pneumatic actuator:

single acting with closing spring (NC)

ISO-KF and CF-F

Manual: File:Mini UHV gate valve Manual.pdf

File:Mini UHV gate valve.pdf

[1]

Leak rate: body / valve seat: [math] \lt 5 \times 10^{-10}/ \lt 1 \times 10^{-9}~mbar~Is^{-1} [/math]

Pressure range: [math] 1 \times 10{-10} [/math] mbar to 2 bar (abs)

1 millibar = 0.750061683 torr = 0.75 torr


The 24 VDC is for the solenoid.
The large round connector in your photos is for the electrical position indicators. The contact rating is up to 50 VDC at 3 A or 250 VAC at 5 A max.


Sadiq,

You require 55 – 100 psig into the solenoid.   Applying 24 VDC to the solenoid will open the valve and removing it will close the  valve.

Your valve is a normally closed valve, meaning it is spring closed.  Reference the part number in the manual that ends in 41.

Give me a call If you have any questions.

Regards,

Bill McPheeters
VAT Sales Engineer - Austin, TX
T: 512-280-8050, F: 512-280-8054


Solenoid pinning:

Apply 24 volts between Pin 1 and Pin 2 ([math]V_{pin1} - V_{pin2} = +24~V[/math])
Pin 1: +
Pin 2: -
Ground:

My wiring:

Black = hot

White = neutral

Green = ground

Parts needed

Relay (switch), sensor and bus (terminal).

Ion Pump

DUNIWAY

STOCKROOM CORP.

ION PUMP CONTROL UNIT

IPC - 0062

pump manual: [2]

File:DUNIWAY ION PUMP Manual.pdf

Use with a Pressure Relay

A multi pin connector (J2) is provided on the rear panel to connect the IPC-0062 to a pressure relay, such as the Varian 924-0048 or the Duniway Stockroom Corporation PR-0048. This accessory is used for controlling the heaters in a bakeout unit for the pump and system.

For use of the Pressure Relay, consult the instruction manual supplied with the unit. The IPC0-0062 is fully compatible with the 924-0048 and PR-0048.

PR-0048

website: [3]

Manual [4]

Price: $810.00


924-0048

Website: [5]

Price: $745.50

Gun

Electron Gun has a diameter of 1.2 cm.

HRRL Gun Diameter 1.jpg HRRL Gun Diameter 2.jpg HRRL Gun Diameter 3.jpg HRRL Gun Diameter 4.jpg HRRL Gun Diameter 5.jpg HRRL Gun Diameter 6.jpg HRRL Gun Diameter 7.jpg