Difference between revisions of "X-pinch driver 2-bricks fabrication"

From New IAC Wiki
Jump to navigation Jump to search
(Blanked the page)
 
(248 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[https://wiki.iac.isu.edu/index.php/RS#Compact_and_Portable_X-Pinch_Driver go back]
 
  
−
 
−
12/08/13
 
−
*The updated drawing of bricks with remeasured front plate's holes created (drawing #2013.1.001.0001)
 
−
 
−
 
−
12/09/13
 
−
*The list of possible manufacturing company for Brick's Housing (BH) parts production is established:
 
−
**Partner Steel Co, Inc, Pocatello;
 
−
**Valley Sheet Metal (VSM) Technologies, Idaho Falls;
 
−
**Primear Technology, Blackfoot;
 
−
**Northwest wire EDM, Spokane, WA;
 
−
**Nelson Metal Technology, Payette, ID;
 
−
**Water Jet Cutting, Albuquerque;
 
−
*All above companies have been contacted for quotes. Criteria were price and speed of production.
 
−
 
−
 
−
12/10/13
 
−
*Brick's Housing (BH) parts (steel/AL/PMMA sheets) drawings is approved by Spielman (drawings #2013.1.001.0002-0009)
 
−
 
−
 
−
12/11/13
 
−
*VSM Technologies: selected as manufactured company for BH parts (drawings #2013.1.001.0002-0009)
 
−
 
−
 
−
12/17/19
 
−
*BH parts arrived at IAC and inspected. Kevin is going to assemble and weld them all together.
 
−
 
−
 
−
12/18/19
 
−
*Cathode/anode drawings submitted to Spielman for approving (drawings #2013.1.001.0010-0017)
 
−
*PMMA_Output_Sheet/Charging_Isolating_Tube drawings submitted to Spielman for approving (drawings #2013.1.001.0018-0019)
 
−
*X-pinch driver assembly drawing with included cathode/anode submitted to Spielman for approving (drawing #2013.1.001.0020)
 
−
*PARKER's Viton O-rings V0769-60 2-246 (2 pcs), ID 4 1/2 and W 1/8", selected for vacuum seal inside the cathode/anode section.
 
−
 
−
 
−
12/19/13
 
−
*LESKER reduced 4-way cross (C-0800-275, $890) found as a candidate for vacuum chamber
 
−
*LESKER reduced 4-way cross drawing downloaded and incorporated into SolidWorks (assembly file Lesker_C-800_275\C-0800-275_reassembled)
 
−
*LESKER reduced 4-way cross redesigned to match our x-pinch driver (drawing file Lesker_C-800_275\LESKER_C-0800-275_REASSEMBLED)
 
−
 
−
 
−
12/20/13
 
−
*Some changes to parts have been done to accommodate LESKER redesigned cross:
 
−
**1) for Al output plate, the inner cut increased from 4.5 diameter to 10" diameter to match the cross (drawing #2013.1.001.0008);
 
−
**2) for anode can, the slot size increased from 0.4" to 0.5" to march x-pinch wires length  (drawing #2013.1.001.0014);
 
−
*Reassembled LESCER cross drawing submitted to Spielman for approving (drawing LESKER C-0800-275_REASSEMBLED)
 
−
*X-pinch driver assembly drawing with included cathode/anode/cross submitted to Spielman for approving (drawing #2013.1.001.0021)
 
−
*LESCER cross and new assembly drawings is approved by Spielman:
 
−
 
−
 
−
12/23/13
 
−
For x-pinch vacuum chamber we will need:
 
−
* 4-way reducing cross, (8" and  2 3/4" flanges), part #C-0800-275, $890. Comments: this one we will cut and reassemble later in the way we need. Just to remind, I plan two use one 8" flange for plate connection, one 8" flange for x-pinch access and vacuum pump connection, one 2 3/4 flange for x-ray diagnostics and one 2 3/4 flange for x-ray output.
 
−
 
−
 
−
Think about those:
 
−
* 8" fixed blank CF flange, part #F0800X000N, $125;
 
−
* No, need flange with windows: 2 3/4" fixed blank CF flange, part #F0275X000N, $15;
 
−
* 2 3/4" fixed bore 1.63" CF flange, part #F0275X175N, $15;
 
−
* 1/4 Hard OFHC Copper Gasket for 2-3/4" CF flange, part #GA-0275, set of 10, $26.40;
 
−
* 1/4 Hard OFHC Copper Gasket for 8" CF flange, part #GA-0800, set of 10, $75.00. Comments: I would buy two sets, as these gaskets will be sealing the 8" flange for x-pinch access.
 
−
 
−
 
−
Buy those latter with all fasteners:
 
−
* '''1/4—28 x 1-3/8" Bolt & Nut Set, part #HBS25028138, set of 25, $29.38;'''
 
−
* '''5/16—24 x 2-1/4" Bolt & Nut Set, part #HBS31224225, set of 25, $37.58;'''
 
−
* '''5/16—24 x 1-3/4" Bolt Kits, part #HBK31224175, set of 25, $30.60;  (need 1" length)'''
 
−
 
−
Total quote is '''xxx.xx''' plus shipping. 
 
−
 
−
 
−
 
−
To Do List:
 
−
*Can we use cross instead of cube? (A: Cross - not, but reduced cross - yes)
 
−
*Do we need to use Cu gasket to seal CF flange? If so, we need a lot of them for every shot.(A: yes, we need to use Cu gaskets);
 
−
*Identify/buy all needed flanges/gaskets for the cross; (done)
 
−
*o-ring in PMMA ~3 mm. Locate position and include in drawing. (done)
 
−
*Order cross/flanges/gaskets/fasteners, RACL60;
 
−
*Include all taped holes in drawing;
 
−
*Include groove for two o-rings into the isolating output PMMA drawing, #2013.1.001.0018
 
−
*Fabricate anode/cathode/vacuum_chamber parts (drawings #2013.1.001.0010-0021)
 
−
*Locate vacuum pump
 
−
*Diagnostics: Rogowskii and B-Dot, design and include in drawing
 

Latest revision as of 22:40, 22 January 2014

Retrieved from "https://wiki.iac.isu.edu/index.php?title=X-pinch_driver_2-bricks_fabrication&oldid=90768"