Difference between revisions of "X-pinch driver 2-bricks fabrication"

Revision as of 07:14, 21 December 2013

12/08/13

The updated drawing of bricks with remeasured front plate's holes created (drawing #2013.1.001.0001)

12/09/13

The list of possible manufacturing company for Brick's Housing (BH) parts production is established:
- Partner Steel Co, Inc, Pocatello;
- Valley Sheet Metal (VSM) Technologies, Idaho Falls;
- Primear Technology, Blackfoot;
- Northwest wire EDM, Spokane, WA;
- Nelson Metal Technology, Payette, ID;
- Water Jet Cutting, Albuquerque;
All above companies have been contacted for quotes. Criteria were price and speed of production.

12/10/13

Brick's Housing (BH) parts (steel/AL/PMMA sheets) drawings is approved by Spielman (drawings #2013.1.001.0002-0009)

12/11/13

VSM Technologies: selected as manufactured company for BH parts (drawings #2013.1.001.0002-0009)

12/17/19

BH parts arrived at IAC and inspected. Kevin is going to assemble and weld them all together.

12/18/19

Cathode/anode drawings submitted to Spielman for approving (drawings #2013.1.001.0010-0017)
PMMA_Output_Sheet/Charging_Isolating_Tube drawings submitted to Spielman for approving (drawings #2013.1.001.0018-0019)
X-pinch driver assembly drawing with included cathode/anode submitted to Spielman for approving (drawing #2013.1.001.0020)
PARKER's Viton O-rings V0769-60 2-246 (2 pcs), ID 4 1/2 and W 1/8", selected for vacuum seal inside the cathode/anode section.

12/19/13

LESKER reduced 4-way cross (C-0800-275, $890) found as a candidate for vacuum chamber
LESKER reduced 4-way cross drawing downloaded and incorporated into SolidWorks (assembly file Lesker_C-800_275\C-0800-275_reassembled)
LESKER reduced 4-way cross redesigned to match our x-pinch driver (drawing file Lesker_C-800_275\LESKER_C-0800-275_REASSEMBLED)

12/20/13

Some changes to parts have been done to accommodate LESKER redesigned cross:
- 1) for Al output plate, the inner cut increased from 4.5 diameter to 10" diameter to match the cross (drawing #2013.1.001.0008);
- 2) for anode can, the slot size increased from 0.4" to 0.5" to march x-pinch wires length (drawing #2013.1.001.0014);
Reassembled LESCER cross drawing submitted to Spielman for approving (drawing LESKER C-0800-275_REASSEMBLED)
X-pinch driver assembly drawing with included cathode/anode/cross submitted to Spielman for approving (drawing #2013.1.001.0021)
LESCER cross and new assembly drawings is approved by Spielman:

12/21/13

To Do List:

order cross on Monday, RACL60;
include all taped holes in drawing;
identify/buy all needed flanges/gaskets for the cross;
do we need to use Cu gasket to seal CF flange? If so, we need a lot of them for every shot.(A: yes, we need to use Cu gaskets);
o-ring in PMMA ~3 mm. Locate position and include in drawing. (Done)
Include groove for two o-rings into the isolating output PMMA drawing, #2013.1.001.0018
Can we use cross instead of cube? (A: Cross - not, but reduced cross - yes)
Fabricate anode/cathode/vacuum_chamber parts (drawings #2013.1.001.0010-0021)
Locate vacuum pump
Diagnostics: Rogowskii and B-Dot, design and include in drawing

@@ Line 60: / Line 60: @@
 ***5/16"—24 x 2-1/4" Reducer Bolt Set, LESKER part #HBS31224225, set of 25, $37.58;
 **Flanges:
+***2 3/4" fixed blank CF flange, LESKER part#F0275X000N, $15;
+***2 3/4" fixed bore 1.63" CF flange, LESKER part#F0275X175N, $15;
+***8" fixed blank CF flange, LESKER part#F0800X000N, $125;
+**Total budget: $383.98
@@ Line 67: / Line 70: @@
 *include all taped holes in drawing;
 *identify/buy all needed flanges/gaskets for the cross;
-**one 2 3/4 CF fixed blank flange. Lesker part # F0275X000N, $15;
-**
 *do we need to use Cu gasket to seal CF flange? If so, we need a lot of them for every shot.(A: yes, we need to use Cu gaskets);
 *o-ring in PMMA ~3 mm. Locate position and include in drawing. (Done)