Difference between revisions of "TF EIMLab14 Writeup"

From New IAC Wiki
Jump to navigation Jump to search
Line 10: Line 10:
 
:a. Try <math>R_E \approx 220 \Omega</math>  
 
:a. Try <math>R_E \approx 220 \Omega</math>  
 
:b. <math>I_C > 0.5</math> mA DC with no input signal
 
:b. <math>I_C > 0.5</math> mA DC with no input signal
 +
:c. <math>V_{CE} \approx V_{CC}/2 > 2</math> V
 +
:d. <math>V_{CC} < V_{CE}(max)</math> to prevent burnout
 +
 +
 +
 +
V_{CE}(max) = 40 Volts
 +
 +
so <math>V_{CC} < 40</math>
  
 
To set this collector current you ned to choose V_{CC} and R_C to give 0.5 mA and be in the middle of the load line.
 
To set this collector current you ned to choose V_{CC} and R_C to give 0.5 mA and be in the middle of the load line.
  
 +
From previous lab we should try V_{CE} = 1 Volt
 +
 +
Loop theorem \Rightarrow
 +
 +
:<math>V_{CC} - I_CR_C - V_{CE} - I_ER_E = 0</math>
 +
 +
:<math>V_{CE} = V_{CC}/2</math>
 +
 +
:<math>\RIghtarrow  V_{CC}/2 = I_C R_C + I_E R_E</math>
 +
: Since <math>I_C \approx I_E</math>
 +
 +
: <math>V_{CC} = 2I_E (R_C+R_E)</math>
  
From previous lab we should try V_{CE} = 1 Volt
 
  
If V_{CC} = 10 Volts then R = \frac{10}{0.0005} = 200 k \Omega
 
  
:c. <math>V_{CE} \approx V_{CC}/2 > 2</math> V
 
:d. <math>V_{CC} < V_{CE}(max)</math> to prevent burnout
 
 
:e. <math>V_{BE} \approx 0.6 V</math>
 
:e. <math>V_{BE} \approx 0.6 V</math>
 
:f. <math>I_D \approx 10 I_B < 1</math> mA  
 
:f. <math>I_D \approx 10 I_B < 1</math> mA  

Revision as of 17:49, 30 March 2011

The Common Emitter Amplifier

Circuit

1.)Construct the common emitter amplifier circuit below according to your type of emitter.

TF EIM Lab14a.png

2.)Calculate all the R and C values to use in the circuit such that

a. Try [math]R_E \approx 220 \Omega[/math]
b. [math]I_C \gt 0.5[/math] mA DC with no input signal
c. [math]V_{CE} \approx V_{CC}/2 \gt 2[/math] V
d. [math]V_{CC} \lt V_{CE}(max)[/math] to prevent burnout


V_{CE}(max) = 40 Volts

so [math]V_{CC} \lt 40[/math]

To set this collector current you ned to choose V_{CC} and R_C to give 0.5 mA and be in the middle of the load line.

From previous lab we should try V_{CE} = 1 Volt

Loop theorem \Rightarrow

[math]V_{CC} - I_CR_C - V_{CE} - I_ER_E = 0[/math]
[math]V_{CE} = V_{CC}/2[/math]
[math]\RIghtarrow V_{CC}/2 = I_C R_C + I_E R_E[/math]
Since [math]I_C \approx I_E[/math]
[math]V_{CC} = 2I_E (R_C+R_E)[/math]


e. [math]V_{BE} \approx 0.6 V[/math]
f. [math]I_D \approx 10 I_B \lt 1[/math] mA

3.)Draw a load line using the [math]I_{C}[/math] -vs- [math]I_{CE}[/math] from the previous lab 13. Record the value of [math]h_{FE}[/math] or [math]\beta[/math].

4.)Set a DC operating point [math]I^{\prime}_C[/math] so it will amplify the input pulse given to you. Some of you will have sinusoidal pulses others will have positive or negative only pulses.

5.)Measure all DC voltages in the circuit and compare with the predicted values.(10 pnts)

6.)Measure the voltage gain [math]A_v[/math] as a function of frequency and compare to the theoretical value.(10 pnts)

7.)Measure [math]R_{in}[/math] and [math]R_{out}[/math] at about 1 kHz and compare to the theoretical value.(10 pnts)

How do you do this? Add resistor in front of [math]C_1[/math] which you vary to determine [math]R_{in}[/math] and then do a similar thing for [math]R_{out}[/math] except the variable reistor goes from [math]C_2[/math] to ground.

8.)Measure [math]A_v[/math] and [math]R_{in}[/math] as a function of frequency with [math]C_E[/math] removed.(10 pnts)

Questions

  1. Why does a flat load line produce a high voltage gain and a steep load line a high current gain? (10 pnts)
  2. What would be a good operating point an an [math]npn[/math] common emitter amplifier used to amplify negative pulses?(10 pnts)
  3. What will the values of [math]V_C[/math], [math]V_E[/math] , and [math]I_C[/math] be if the transistor burns out resulting in infinite resistance. Check with measurement.(10 pnts)
  4. What will the values of [math]V_C[/math], [math]V_E[/math] , and [math]I_C[/math] be if the transistor burns out resulting in near ZERO resistance (ie short). Check with measurement.(10 pnts)
  5. Predict the change in the value of [math]R_{in}[/math] if [math]I_D[/math] is increased from 10 [math]I_B[/math] to 50 [math]I_B[/math](10 pnts)
  6. Sketch the AC equivalent circuit of the common emitter amplifier.(10 pnts)

Forest_Electronic_Instrumentation_and_Measurement