Difference between revisions of "Se170063"

From New IAC Wiki
Jump to navigation Jump to search
Line 24: Line 24:
  
 
=Nickel Information=
 
=Nickel Information=
In finding the initial activity of the front nickel foil of this sample, look at the window from [1356,1368]. The method I used here was simply finding the number of counts within this window and subtracting the integral of the constant found by the fit. Below is a picture of the line of interest.
 
  
[[File:170063 003 NickelSpectrum.png|200px]]
+
[[Se170063 Nickel Investigation]]
 
 
Note that this spectrum is weighted by the inverse of the mass of the nickel. So the natural log of the activity is what we want to put in the .dat file to feed into root. Below is the math that I did to find these numbers
 
 
 
<math> N = N_{total} - \int_{1356}^{1368} C dE </math>
 
 
 
 
 
After the number of counts have been found, I used the following formula for the error
 
 
 
<math> \sigma_N = \sqrt{N} </math>
 
 
 
So now we have the number of counts for the line of interest and its associated error, so we must convert this into an activity, correct for the efficiency, and take the natural log.
 
 
 
<math> A_t = \frac{N_t}{t} </math>
 
 
 
<math>  \sigma_{A_t} = \frac{\sigma_{N}}{t} </math>
 
 
 
<math> A'_t = \frac{A_t}{\epsilon} </math>
 
 
 
<math> \sigma_{A'_t} = \frac{\sigma_{A_t}}{\epsilon} </math>
 
 
 
Now we can simply take the natural log of the efficiency corrected activity. To find the error after taking the natural log, use
 
 
 
<math> \sigma_{\ln{A'_t}} = \frac{\sigma_{A'_t}}{A'_t} </math>
 
 
 
 
 
Below is the plot for the activity and half life of the nickel foil
 
 
 
[[File:170063 003 HalfLifePlot.png|200px]]
 
 
 
 
 
Using the slope of this graph, we can find that the half life is
 
 
 
<math> t_{\frac{1}{2}} = \frac{\ln{2}}{\lambda} = 35.71 hours </math>
 
 
 
<math> \sigma_{t_{\frac{1}{2}}} = \frac{\ln{2}*\sigma_{lambda}}{\lambda^2} = 0.04 hours</math>
 
 
 
 
 
This does capture the accepted half life of Ni-57 in 2 standard deviations, which is a good sign.
 
 
 
Using the method below and doing a time correction backward 5280 seconds to coincide with the first selenium mixture measurement, we find the activity of the nickel is
 
 
 
 
 
<math> A_0 = 1835578.669 \pm 3268.41  \rightarrow 49.61  \pm 0.88 \mu Ci</math>
 
  
 
=Activity and Half Life=
 
=Activity and Half Life=

Revision as of 14:48, 18 October 2017

PAA_Selenium/Soil_Experiments#Selenium_Sample_Analysis

Sample Description

The sample was placed in an aluminum cylinder that was to be irradiated. The target components consisted of a nickel foil on the front of the cylinder with 2 pure selenium pellets under the foil, but still outside the cylinder. Inside the target there was burnt sagebrush ash, which was burned with a blowtorch, and selenium. Below are the masses of the components

Nickel Foil: 0.2783g

Outer Se Pellets: 0.0971g

Sage Ash: 0.5111g

Inner Se Pellets: 0.0523g

Energy

LB May Calibration 2017

The Calibration for Detector A was done on the morning of 5/23/17 with the MPA software using the thorium rods (as the calibration was fairly close already) and the correction values were found to be Det A Intercept = -12.208800 slope =1.021270


Efficiency

LB May 2017 Det A Efficiency

Nickel Information

Se170063 Nickel Investigation

Activity and Half Life

Se170063 Activity And Half Life

Alternative Method

Se170063 Activity and HL Alternate

Corrected Alternative method

This time the number of counts was weighted by the mass of the selenium (shouldn't it be Se+ash??) sample.

Runlist

Table with dates and filename and locations on daq1

LB_May_2017_Irradiation_Day#10.25_Se_Soil_Mix

PAA_Selenium/Soil_Experiments#Selenium_Sample_Analysis