Difference between revisions of "PFD:Production of Fabrication Drawings"

From New IAC Wiki
Jump to navigation Jump to search
 
(7 intermediate revisions by the same user not shown)
Line 8: Line 8:
  
 
= Drawings=
 
= Drawings=
 +
 +
These Drawings are based on the following parameters
 +
 +
1. 10mm of wire feed through is projected inward from the end plate
 +
 +
2. The Maximum diameter of the ring which would touch all the nose plate faces is 10 inches
 +
 +
3. Distance between wire planes in super layer 5 is 8.6 mm
 +
 +
4. Distance between wire planes in super layer 6 is 9 mm
 +
 +
5. Chamber tilt angle is 25 Degrees
 +
 +
6. Min Electron Scattering angle is 4.5 Degrees
 +
 +
7. Distance to the first sense wire from the target center is 4.804842 meters
 +
 +
8. Wire angles are 6 degrees with opposite slopes on the center line with reference to a horizontal in the chamber tilt plane
 +
 +
Assembly drawing of a sector [[Image:Sep25. B00000-01-10-0001.pdf]]
 +
 +
[[Image:AssemblyDrawing_9-25-08.jpg | 400 px]]
 +
 +
 
==Nose Plate==
 
==Nose Plate==
 
[[Image:Sep25. B00000-01-10-0002.pdf]]
 
[[Image:Sep25. B00000-01-10-0002.pdf]]
Line 94: Line 118:
 
[[Image:Sep. B00000-01-10-00018.pdf]]
 
[[Image:Sep. B00000-01-10-00018.pdf]]
  
==Chamber holding support sheets==
+
==carbon rods==
 +
 
 +
[[Image:Sep. B00000-01-10-00019.pdf]]
 +
 
 +
==Chamber holding support plates==
  
 
[[Image:Sep. B00000-01-10-00020.pdf]]
 
[[Image:Sep. B00000-01-10-00020.pdf]]

Latest revision as of 14:36, 16 October 2008

Drawings should include the following information

  1. dimension units (mm or inch)
  2. Vendor
  3. tolorances
  4. assembly drawing number
  5. material finish when appropriate

Drawings

These Drawings are based on the following parameters

1. 10mm of wire feed through is projected inward from the end plate

2. The Maximum diameter of the ring which would touch all the nose plate faces is 10 inches

3. Distance between wire planes in super layer 5 is 8.6 mm

4. Distance between wire planes in super layer 6 is 9 mm

5. Chamber tilt angle is 25 Degrees

6. Min Electron Scattering angle is 4.5 Degrees

7. Distance to the first sense wire from the target center is 4.804842 meters

8. Wire angles are 6 degrees with opposite slopes on the center line with reference to a horizontal in the chamber tilt plane

Assembly drawing of a sector File:Sep25. B00000-01-10-0001.pdf

AssemblyDrawing 9-25-08.jpg


Nose Plate

File:Sep25. B00000-01-10-0002.pdf

Left End Plate

Left End Plate assembly was drawn in 5 Drawings to complete the assembly

Left End Plate Assembly View: File:Sep25. B00000-01-10-0003.pdf

  • A sample of hole positions are available in sheet 2

Left End Plate Frame: Frame has 5 sheets File:Sep25. B00000-01-10-0004.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Nose side Close Out
  • Sheet 5. back plate side Close Out

Left End Plate Core: Core File:Sep25. B00000-01-10-0005.pdf

Left End Plate inner skin: File:Sep25. B00000-01-10-0006.pdf

Left End Plate outer skin: File:Sep25. B00000-01-10-0007.pdf

Right End Plate

Right End Plate assembly was drawn in 5 Drawings to complete the assembly

Right End Plate Assembly View: File:Sep25. B00000-01-10-0008.pdf

  • A sample of hole positions are available in sheet 2

Left End Plate Frame: Frame has 5 sheets File:Sep25. B00000-01-10-0009.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Nose side Close Out
  • Sheet 5. back plate side Close Out

Right End Plate Core: Core File:Sep25. B00000-01-10-0010.pdf

Right End Plate inner skin: File:Sep25. B00000-01-10-0011.pdf

Right End Plate outer skin: File:Sep25. B00000-01-10-0012.pdf


Back Plate

Back Plate assembly was drawn in 5 Drawings to complete the back plate assembly

Back Plate Assembly View: File:Sep. B00000-01-10-00013.pdf

Back Plate Frame: Frame has 5 sheets File:Sep. B00000-01-10-00014.pdf

  • Sheet 1: Frame assembly
  • Sheet 2: Upstream Close out
  • Sheet 3. Downstream Close out
  • Sheet 4. Right Close Out
  • Sheet 5. left Close Out

Back Plate Core: File:Sep. B00000-01-10-00015.pdf

Back Plate inner skin: File:Sep. B00000-01-10-00016.pdf

Back Plate outer skin: File:Sep. B00000-01-10-00017.pdf


Hexcel Backing sheet

File:Sep. B00000-01-10-00018.pdf

carbon rods

File:Sep. B00000-01-10-00019.pdf

Chamber holding support plates

File:Sep. B00000-01-10-00020.pdf