Difference between revisions of "Niowave Report 11-30-2015"

From New IAC Wiki
Jump to navigation Jump to search
Line 40: Line 40:
  
 
[[File:TF_Niowave_SolenoidDesign_9-11-15.png | 200 px]]
 
[[File:TF_Niowave_SolenoidDesign_9-11-15.png | 200 px]]
 +
 +
{| border="1"
 +
|Element || dimension
 +
|-
 +
| Inner beam pipe radius || 1.74 cm
 +
|-
 +
| Inner beam pipe thickness || 0.165 cm
 +
|-
 +
|water jacket thickness || 0.457 cm
 +
|-
 +
| outer beam pipe radius || 2.362 cm
 +
|-
 +
| outer beam pipe thickness || 0.165 cm
 +
|-
 +
| Solenoid inner radius || 2.527 cm
 +
|-
 +
| Solenoid outer radius || 4.406 cm
 +
|}
  
  
  
 
[[G4Beamline_PbBi#Reports]]
 
[[G4Beamline_PbBi#Reports]]

Revision as of 17:12, 29 November 2015

Overview

This report investigates the impact of target thickness and the use of an external solenoid for the production of positrons using a 10 MeV electron beam. A electron beam energy of 10 MeV is chosen as a compromise between maximizing the production of bremstrahlung photons and minimizing the production of neutrons that occur when an MeV energy electron beam interects with a dense metal. A converter target of liquid Lead-Bismuth Eutectic (LBE) is chosen with a concentration of 44.5% lead and 55.5% bismuth in order to provide a high atomic number (Z) material to increase bremstrahlung production that will also absorb the heat deposited when the material is traversed by an MeV electron beam. This work used the simulation package GEANT4 to predict the impact of target thickness and the use of a solenoid magnetic field on positron production efficiency as well as the amount of energy that will be deposited in the apparatus when using a 3.48 cm diameter beam pipe.

Target optimization

Optimal Thickness

One method to produce positrons relies on the creation of positron-electron pairs from the bremsstrahlung photons that are produced when electrons traverse material with a high atomic number (Z). While thicker material encourages the production of these photons, the increased thickness will also cause the produced positrons to annihilate within the material before they can escape. As a result, there is an optimal thickness which will balance the two processes to maximize positron production. A simulation was performed to determine the optimal thickness using a 10 MeV electron beam with a 1cm radius uniform cylindrical spatial distribution impinging a windowless PbBi target. The target thickness was changed to determine the optimal thickness for emmitt positrons from the downstream surface of the LBE target. The simulation was performed by two separate investigators using separate simualotion packages. The results, shown below, indicate that a LBE target thicknes of about 2mm will produce about two positrons for every thousand electrons impinging the PbBi target. The postrons leaving the downstream side of the target will have a momentum of approximately 2 MeV whereas the electrons that penetrate the PbBi target will have lost more than 3 MeV.

PbBi 5-1-15 Ppositron.pngPbBi 5-1-15 Pelectron.pngG4Bl-vs-MCNPX 5-5-2015.png

Optimal Solenoidal Field

Beam Pipe heating

The energy deposited by electrons scattered into a 3.48 diameter stainless steel beam pipe (1.65 mm thick) from a PbBi target as a function of a uniform Solenoidal magnetic field.

The histogram is binned in 100 (10 cm) bin widths. The surface area becomes [math]10 cm \times 2 \pi 3.48/2 = 109.33 cm^2[/math]


To convert From Mev/ e- to kW/cm^2 assuming a current of 1mA (10^-3 C/s) you

[math]\left( \frac{\mbox{MeV}}{\mbox{cm}^2 \mbox{e}^-}\right) \times \left( \frac{ \mbox{e}^-}{1.6 \times 10^{-19}\mbox{C}} \right ) \times \left( \frac{1 \times 10^{-3} \mbox{C}}{\mbox{s}} \right ) \times \left( \frac{1.6 \times 10^{-13}\mbox{W} \cdot \mbox{ s}}{\mbox{MeV} }\right )[/math]

[math]\left( \frac{\mbox{keV}}{\mbox{cm}^2 \mbox{e}^-}\right) = \left( \frac{\mbox{W} }{\mbox{cm}^2 } \right )[/math]


BeamPipeDepEmev-vs-B.png BeamPipeDepPower-vs-B.png
Energy deposited (MeV) along a 1 m long beam pipe of stainless steel 1.65 mm thick.

Solenoid Description

A 10 MeV electron beam with a radius of 0.5 cm was incident on a 2 mm thick PbBi target. The target is positioned at Z = -901 mm.


TF Niowave SolenoidDesign 9-11-15.png

Element dimension
Inner beam pipe radius 1.74 cm
Inner beam pipe thickness 0.165 cm
water jacket thickness 0.457 cm
outer beam pipe radius 2.362 cm
outer beam pipe thickness 0.165 cm
Solenoid inner radius 2.527 cm
Solenoid outer radius 4.406 cm


G4Beamline_PbBi#Reports