Difference between revisions of "Lab 1 TF EIM"

From New IAC Wiki
Jump to navigation Jump to search
Line 23: Line 23:
 
To get measurable currents you need low resistance BUT the lower resistances will need to have a high power rating.  These two competing properties limit the range of resistances you can use.
 
To get measurable currents you need low resistance BUT the lower resistances will need to have a high power rating.  These two competing properties limit the range of resistances you can use.
  
==Construct the circuit below.==
+
==Construct the circuit below==
  
  
 
[[File:TF_EIM_Lab1.png | 400 px]]
 
[[File:TF_EIM_Lab1.png | 400 px]]
 +
 +
==Equations==
 +
 +
Given <math>V_A</math> and the values of all resistors, predict the values of the three currents.
  
 
==Enter the values of the DC voltage and Resisters that you used.==
 
==Enter the values of the DC voltage and Resisters that you used.==

Revision as of 05:18, 1 December 2010

Kirchoff's Law (50 pnts)

Smoky Circuits

When doing these labs it is important to determine the limitations of your electrical components in order to avoid damaging them

This lab uses resistors. Resistors are vulnerable to melting if you push too much current through them.

Resistors have power ratings ranging from 1/8 Watt up to several Watts. The common resistors are rated at 1/4 Watt. Let's assume this rating for the resistors in is lab.

Determine the maximum voltage of the DC power supply you will use. (ie, 30 Volts)

[math] P =I^2R = V^2/R \Rightarrow R = \frac{V^2}{P} \gt \frac{\left (30 V \right)^2}{1/4 \mbox{Watt}} \gt 400 \Omega[/math]
By keeping your resistance values above 400 [math]\Omega[/math] you should be able to avoid burning up 1/4 Watt resistors.

The next objective is to use resistors which allow currents that you can measure with your voltmeter.

Since V=IR \Rightarrow I = V/R = 30 Volts/400 \Omega = 0.75 mA

Determine the range of currents which the voltmeter can measure. (ie 1 mA)

To get measurable currents you need low resistance BUT the lower resistances will need to have a high power rating. These two competing properties limit the range of resistances you can use.

Construct the circuit below

TF EIM Lab1.png

Equations

Given [math]V_A[/math] and the values of all resistors, predict the values of the three currents.

Enter the values of the DC voltage and Resisters that you used.

Use a voltmeter to measure the potential difference and resistances.

Variable Measured Value
[math]V_A [/math]
[math]V_B [/math]
[math]R_1[/math]
[math]R_2[/math]
[math]R_3[/math]

Enter the measured and predicted quantities in the table below

Use Kirchoff's laws to predict the Voltage ([math]V_C[/math]) and current values and compare them to your measurements by filling in the table below.

Variable Measured Value Predicted Value % Difference
[math]V_B[/math]
[math]I_1[/math]
[math]I_2[/math]
[math]I_3[/math]

Internal resistance (30 pnts)

Measure the internal resistance of your power source by graphing the potential difference on the x-axis and the current on the y-axis for several values of the resistance [math]R_L[/math] shown in the circuit below. Begin with [math]R_L = 1k\Omega[/math] and then decrease it by a factor of 5 for each subsequent measurement. You can use a volt meter to measure the current and potential difference.

Questions (20 pnts)

  1. What conservation law is involved in Kirchoff's Loop Theorem?
  2. What does the slope in the internal resistance plot above represent?


Forest_Electronic_Instrumentation_and_Measurement