Difference between revisions of "June,18,2007 Teachers in lab"

From New IAC Wiki
Jump to navigation Jump to search
Line 52: Line 52:
| 0 || 100 || 9
| 0 || 100 || 9
| 1 || 119 || 0.09e3
| 1 || 119 || 10
| 2.5 || 24 || 5
| 2.5 || 24 || 5
==Thursday , June 21, 2007 ==
==Thursday , June 21, 2007 ==

Latest revision as of 02:09, 22 June 2007


  1. Jenette Briggs (Alta H.S. , Sandy, Utah)
  2. Keith Quigley (Roy H.S. , Roy Utah)
  3. Bettie Keetch (Council H.S., Council, ID)
  4. Tony Forest (ISU, Pocatello, ID)

Monday, June 18, 2007

Our Quarknet Teachers had their first session experimenting with a coscmic ray test stand made up of two scintillators. Each scintillator was attached to a single PMT. A voltage of -900 Volts was applied and signals were observed using an oscilloscope.

First Cosmic ray scope pictures using PMT + Scintillator

First scope picture on a single detector


now look for a coincidence signal between two PMT detectors


Tuesday , June 19, 2007

Today our team of experimenters setup a discriminator (LeCroy Model 821) to determine which of the PMT outputs would be used to define the presence of a charged particle passing through the scintillator. The discriminator takes a signal from the PMT that is above the threshold (-30mV to -9V)and returns a voltage of -lV square pulse.

The voltage for each channel was set so that the trigger rates from the discriminator were the same (about 21 pulse/second). Channel A voltage -1075V, Discriminator threshold -30mV, Channel B voltage -1001V, Discriminator threshold -30mV.
click to view larger image

Wednesday , June 20, 2007

The goal for our team of experimenters today was to repair the PMT devices to be used in the cosmic ray telescope as well as check for light leaks. We began the day by checking the rate of coincidence pulses in a ten minute interval. Beginning at 10:32 AM we counted 35 pulses after 10 minutes, averaging 3.5 coincidences per minute. Voltage rates and discrimimator thresholds were fixed from the previous day (Channel A -1075 V; Channel B -1001 V; Discriminator Threshold of -30mV for both)

After making some repairs to the PMT we checked them with devices previously known to work and found our repairs to be sucessful.
During the light leak test which involved using a dark room and roaming the cosmic ray detector with a flashlight. Using a -900V source, we saw no evidence of noise outside of our normal contraints.

Our final goal for the day was to determine appropriate distances to place the detectors within the telescope.

Cosmic Ray camera detector separation tests

Finger scintillators with PMTs set to :

PMT N714 HV= -1008 Volts
PMT N715 HV = -1025 Volts

Paddle Separation (cm) Rate (counts/hour) Statistical Error in Rate (Counts/min)
0 100 9
1 119 10
2.5 24 5

Thursday , June 21, 2007

PMT A HV= -977 Volts
PMT B HV = -955 Volts

Paddle Separation (cm) Rate (counts/hour) Statistical Error in Rate (Counts/min)
0 0 9
1 0 0.09e3
5 2:55 5

Summer Solstice!!!!

Today we are hoping to finalize the assemply of the cosmic ray telescope. Before construction we finished a few tests to figure out how far about we want the detectors to be able to move.


This afternoon the pmt device was tested and found to be drawing high current. After careful analysis we decided to canabalize it and rebuild andother PMT in the hopes that it would not draw the high current as well, Unfortunetly it still did and due to time constraints we had to use one from another detector,

The base was also build this afternoon that will allow for range of motion in the vertical plane and 360 degress around.