IAC 2-29-08

From New IAC Wiki
Revision as of 21:08, 14 April 2008 by Oborn (talk | contribs) (→‎B)
Jump to navigation Jump to search

Leap Day run

DC setup

This time the Sense wire HV is set to 1500 to start

90/10 ArCo2

HV settings
Wire Volts current ([math]\mu[/math]A)
Sense 1500
Field -750
Guard 750

DC preamp at 5.6 Volts


Beam Line Configuration

A 1/4 inch diameter collimater is placed in the experimental cell just after a Helium bag inserted in the wall. A 2 cm thick scintillator is place over the beam downstream side of the collimator aligned using a laser. A 3mm diameter collimator is placed just before a 1 kG magnet that is after the DC. The 1 kG magnet placed after the drift chambers deflects charged particles onto a large scintillator paddle.

A logic circuit was wet up to allow for the following trigger configurations

  1. gun AND (Front Scint OR Rear Scint)
  2. gun AND (Front Scint AND Rear Scint)

Increased beam energy from 10 MeV to 12 MeV due to expected energy loss in front scintillator.


Data was taken with the

  1. gun AND (Front Scint OR Rear Scint)

trigger. The back scintillator output is in the data stream (ADC14 in C-convention, ADC15 in ntuple) so A software coincidence will be used. The rate with ANDing all signals was time prohibitive.

Runs

A

Decided to increase beam current until up to 10% of events in front scintilaltor pass through magnet after drift chamber and hit back scintillator. Ran in OR mode so a software coincidence can be formed based on measurement in ADC15 (ADC14 in C convention).

Run # Description
431 0" from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
432 0" from feedthrough , Sense wire at 1500 Volts, Metalica (ADC6; C-convention) sees overflows and looks hot on scope compared to Plastika (ADC8: in ntuples),Gun voltage at 1.76
433 -1" from feedthrough (beam should miss chamber), Sense wire at 1500 Volts, I see peds in Plastika but not metalica (Metalica is beam upstream of Plastika), The overflows are due to DC voltage/Gain being too high ,Gun voltage at 1.76
434 1" from feedthrough , Sense wire at 1500 Volts, Gun voltage at 1.76
435 2" from feedthrough , Sense wire at 1500 Volts, Gun voltage at 1.76

B

Change voltage on DC to values used on last day of January run 90/10 ArCo2

Drift Chamber HV

HV settings
Cable # Volts Current (ma)
Sense +1450
Field -725
Guard +725
Front Scint -1127 30 mV threshold
Rear Scint -1153 81 mV Threshold


Run # Scint counts > 70 channels (ADC15) Scint counts/trigger Description
436 2" (-100k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76, Less overflows in Metalica ADC
437 4" (-200k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
438 1" (-50k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76, visually inspected position and confirmed it was 1" from feedthrough
439 0.5" (-25k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
440 0.25" (-12.5k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
441 0.0625" (-9.375k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
442 -5" (+240.625k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76, try to get electrons missing chamber, use ADC14 to cut on electrons hitting back scintillator. ADC7 should be zero if its really an electron.
443 -3" (+140.625k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
444 -2" (+90.625k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
445 -0.5" (+15.625k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
446 -0.25" (+3.125k) from feedthrough , Sense wire at 1450 Volts, Gun voltage at 1.76
447 Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply On, Preamp Power supply at 5.6 V, trigger: gun OR either scintillator
448 Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off
449 Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off, DC preamp off
450 Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off, DC pramp off, Now just trigger on gun pulse, DC HV off

ADC15 r437 ADC15 r450.gifADC15 r438 ADC15 r447.gifADC15 r439 ADC15 r448.gifADC15 r440 ADC15 r449.gif

Run # r436 r437 r438 r439 r440 r441 r442 r443 r444 r445 r446
Distance(inch) 2" 4" 1" 0.5" 0.25" 0.0625" -5" -3" -2" -0.5 -0.25"
ADC15 ADC15 r436 r447.gif ADC15 r436 r447 1.gif ADC15 r437 r447.gif ADC15 r437 r447 1.gif ADC15 r438 r447.gif ADC15 r438 r447 1.gif ADC15 r439 r447.gif ADC15 r439 r447 1.gif ADC15 r440 r447.gif ADC15 r440 r447 1.gif ADC15 r441 r447.gif ADC15 r441 r447 1.gif ADC15 r442 r447.gif ADC15 r442 r447 1.gif ADC15 r443 r447.gif ADC15 r443 r447 1.gif ADC15 r444 r447.gif ADC15 r444 r447 1.gif ADC15 r445 r447.gif ADC15 r445 r447 1.gif ADC15 r446 r447.gif ADC15 r446 r447 1.gif
3 100px ADC3 r437 with cut gauss fit.gif ADC3 r438 with cut gauss fit.gif ADC3 r439 with cut gauss fit.gif ADC3 r440 with cut gauss fit.gif ADC3 r441 with cut gauss fit.gif ADC3 r442 with cut gauss fit.gif ADC3 r443 with cut gauss fit.gif ADC3 r444 with cut gauss fit.gif ADC3 r445 with cut gauss fit.gif ADC3 r446 with cut gauss fit.gif
4 100px ADC4 r437 with cut gauss fit.gif ADC4 r438 with cut gauss fit.gif ADC4 r439 with cut gauss fit.gif ADC4 r440 with cut gauss fit.gif ADC4 r441 with cut gauss fit.gif ADC4 r442 with cut gauss fit.gif ADC4 r443 with cut gauss fit.gif ADC4 r444 with cut gauss fit.gif ADC4 r445 with cut gauss fit.gif ADC4 r446 with cut gauss fit.gif
5 100px ADC5 r437 with cut gauss fit.gif ADC5 r438 with cut gauss fit.gif ADC5 r439 with cut gauss fit.gif ADC5 r440 with cut gauss fit.gif ADC5 r441 with cut gauss fit.gif ADC5 r442 with cut gauss fit.gif ADC5 r443 with cut gauss fit.gif ADC5 r444 with cut gauss fit.gif ADC5 r445 with cut gauss fit.gif ADC5 r446 with cut gauss fit.gif
6 100px ADC6 r437 with cut gauss fit.gif ADC6 r438 with cut gauss fit.gif ADC6 r439 with cut gauss fit.gif ADC6 r440 with cut gauss fit.gif ADC6 r441 with cut gauss fit.gif ADC6 r442 with cut gauss fit.gif ADC6 r443 with cut gauss fit.gif ADC6 r444 with cut gauss fit.gif ADC6 r445 with cut gauss fit.gif ADC6 r446 with cut gauss fit.gif
7 100px ADC7 r437 with cut gauss fit.gif ADC7 r438 with cut gauss fit.gif ADC7 r439 with cut gauss fit.gif ADC7 r440 with cut gauss fit.gif ADC7 r441 with cut gauss fit.gif ADC7 r442 with cut gauss fit.gif ADC7 r443 with cut gauss fit.gif ADC7 r444 with cut gauss fit.gif ADC7 r445 with cut gauss fit.gif ADC7 r446 with cut gauss fit.gif
8 100px ADC8 r437 with cut gauss fit.gif ADC8 r438 with cut gauss fit.gif ADC8 r439 with cut gauss fit.gif ADC8 r440 with cut gauss fit.gif ADC8 r441 with cut gauss fit.gif ADC8 r442 with cut gauss fit.gif ADC8 r443 with cut gauss fit.gif ADC8 r444 with cut gauss fit.gif ADC8 r445 with cut gauss fit.gif ADC8 r446 with cut gauss fit.gif
9 100px ADC9 r437 with cut gauss fit.gif ADC9 r438 with cut gauss fit.gif ADC9 r439 with cut gauss fit.gif ADC9 r440 with cut gauss fit.gif ADC9 r441 with cut gauss fit.gif ADC9 r442 with cut gauss fit.gif ADC9 r443 with cut gauss fit.gif ADC9 r444 with cut gauss fit.gif ADC9 r445 with cut gauss fit.gif ADC9 r446 with cut gauss fit.gif
10 100px ADC10 r437 with cut gauss fit.gif ADC10 r438 with cut gauss fit.gif ADC10 r439 with cut gauss fit.gif ADC10 r440 with cut gauss fit.gif ADC10 r441 with cut gauss fit.gif ADC10 r442 with cut gauss fit.gif ADC10 r443 with cut gauss fit.gif ADC10 r444 with cut gauss fit.gif ADC10 r445 with cut gauss fit.gif ADC10 r446 with cut gauss fit.gif
11 100px ADC11 r437 with cut gauss fit.gif ADC11 r438 with cut gauss fit.gif ADC11 r439 with cut gauss fit.gif ADC11 r440 with cut gauss fit.gif ADC11 r441 with cut gauss fit.gif ADC11 r442 with cut gauss fit.gif ADC11 r443 with cut gauss fit.gif ADC11 r444 with cut gauss fit.gif ADC11 r445 with cut gauss fit.gif ADC11 r446 with cut gauss fit.gif
12 100px ADC12 r437 with cut gauss fit.gif ADC12 r438 with cut gauss fit.gif ADC12 r439 with cut gauss fit.gif ADC12 r440 with cut gauss fit.gif ADC12 r441 with cut gauss fit.gif ADC12 r442 with cut gauss fit.gif ADC12 r443 with cut gauss fit.gif ADC12 r444 with cut gauss fit.gif ADC12 r445 with cut gauss fit.gif ADC12 r446 with cut gauss fit.gif
Distance(inch)
2"
4"
1"
0.5"
0.25"
0.0625"
-5"
-3"
-2"
-0.5"
-0.25"

Rear Scint Pedestal

Run # Scint Histogram Wire #4 Description
447 R447 ADC15.gif R447 ADC7.gif Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply On, Preamp Power supply at 5.6 V, trigger: gun OR either scintillator
448 R448 ADC15.gif R448 ADC7.gif Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off
449 R449 ADC15.gif R449 ADC7.gif Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off, DC preamp off
450 R450 ADC15.gif R450 ADC7.gif Beam turned off, Pedestal run, Sense wire at 1450 Volts, Translator Power supply Off, DC preamp off, Now just trigger on gun pulse, DC HV off
Observations
The pedestal for the last scintilator is below channel 70. There seems to be a lot of noise around channel 150.
turning the DC amplifier off increases the noise on the line (no more differential amplification).


Go Back