Difference between revisions of "Forest PMTs"
Jump to navigation
Jump to search
(New page: =Hamamatsu R4125HA= Part Number R4125 Type Head on Size 19mm {| |- Specifications |- ActiveDia/L || 15mm Min|| 300nm Max|| 650nm Peak Sens.|| 420nm Cathode Radiant Sensitivity ||...) |
|||
| (16 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Hamamatsu R4125HA= | =Hamamatsu R4125HA= | ||
| − | Part Number | + | [[Image:Hamamatsu_R4125HA_PMT_Pinout.jpg | 300 px]][[Image:Hamamatsu_R4125HA_PMT_Socket.png | 300 px]][[Image:Hamamatsu_R4125HA_VoltDiv.png | 300 px]] |
| − | Type | + | |
| − | Size | + | |
| − | + | [[Image:Hamamatsu_R4125HA_FactoryVoltDiv.png | 300 px]] | |
| − | |- | + | |
| + | |||
| + | {|border="1" |cellpadding="20" cellspacing="0 | ||
| + | |- | ||
| + | | Specifications || | ||
| + | |- | ||
| + | |Part Number || R4125 | ||
| + | |- | ||
| + | |Type || Head on | ||
| + | |- | ||
| + | |Size || 19mm | ||
| + | |- | ||
| + | |ActiveDia/L || 15mm | ||
| + | |- | ||
| + | |Min <math>\lambda</math> ||300nm | ||
| + | |- | ||
| + | |Max <math>\lambda</math> || 650nm | ||
| + | |- | ||
| + | |Peak Sens.|| 420nm | ||
| + | |- | ||
| + | |Cathode Radiant Sensitivity || 90mA/W | ||
| + | |- | ||
| + | |Window || Borosilicate | ||
| + | |- | ||
| + | |Cathode Type || Bialkali | ||
| + | |- | ||
| + | |Cathode Luminous Sensitivity || 115mA/lm | ||
| + | |- | ||
| + | |Cathode Blue Sensitivity Index || 11 | ||
| + | |- | ||
| + | |Anode Luminous Sensitivity || 100A/lm | ||
| + | |- | ||
| + | |Gain || 8.7E+05 | ||
| + | |- | ||
| + | |Dark Current after 30 min. || 10nA | ||
| + | |- | ||
| + | |Rise Time || 2.5ns | ||
| + | |- | ||
| + | |Transit Time|| 16ns | ||
| + | |- | ||
| + | |Transit Time Spread || 0.85ns | ||
| + | |- | ||
| + | |Number of Dynodes|| 10 | ||
| + | |- | ||
| + | |Applied Voltage || 1500V | ||
| + | |- | ||
| + | |Multi Anode|| N | ||
| + | |- | ||
| + | |Magnetic Shield|| E989-02 | ||
| + | |- | ||
| + | |Socket Bare|| E678-12L | ||
| + | |- | ||
| + | |Socket + bleeder assy. ||E974-19 | ||
| + | |- | ||
| + | |Power Supply || C4840 series | ||
|- | |- | ||
| − | + | |Amplifier ||C7319 C6438 C5594 M7279 M8879 | |
| − | + | |} | |
| − | + | ||
| − | + | = HS Student 2009 summer project= | |
| − | + | ||
| − | + | ||
| − | + | ==Dynode chain HV design== | |
| − | + | ||
| − | + | The figure below has several mistakes in ther region near the capacitors. The Hamamatsu drawing scanned in above is correct.. | |
| − | + | ||
| − | + | 1.) There should be no line connecting R11 to the anode. The anode goes from the socket (Pin 5) directly to the output connector. R11 should go to ground as shown. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | 2.) Capacitors C1 and C2 should not be going to ground. C1 should be soldered across Resistor R9( in parallel with R9) and C2 should be soldered across Resistor R10. | ||
| − | | | + | |
| + | [[File:R4125HA_HSstudent2009_HVdivider_Design.png | 200 px]] | ||
| + | |||
| + | ==Base design== | ||
| + | [[File:R4125HA_HSstudent2009_Base_Design.png | 200 px]] | ||
| + | |||
| + | [[File:R4125HA_HSstudent2009_Base_Design_cad.dwg]] | ||
Latest revision as of 22:31, 19 November 2009
Hamamatsu R4125HA
| Specifications | |
| Part Number | R4125 |
| Type | Head on |
| Size | 19mm |
| ActiveDia/L | 15mm |
| Min | 300nm |
| Max | 650nm |
| Peak Sens. | 420nm |
| Cathode Radiant Sensitivity | 90mA/W |
| Window | Borosilicate |
| Cathode Type | Bialkali |
| Cathode Luminous Sensitivity | 115mA/lm |
| Cathode Blue Sensitivity Index | 11 |
| Anode Luminous Sensitivity | 100A/lm |
| Gain | 8.7E+05 |
| Dark Current after 30 min. | 10nA |
| Rise Time | 2.5ns |
| Transit Time | 16ns |
| Transit Time Spread | 0.85ns |
| Number of Dynodes | 10 |
| Applied Voltage | 1500V |
| Multi Anode | N |
| Magnetic Shield | E989-02 |
| Socket Bare | E678-12L |
| Socket + bleeder assy. | E974-19 |
| Power Supply | C4840 series |
| Amplifier | C7319 C6438 C5594 M7279 M8879 |
HS Student 2009 summer project
Dynode chain HV design
The figure below has several mistakes in ther region near the capacitors. The Hamamatsu drawing scanned in above is correct..
1.) There should be no line connecting R11 to the anode. The anode goes from the socket (Pin 5) directly to the output connector. R11 should go to ground as shown.
2.) Capacitors C1 and C2 should not be going to ground. C1 should be soldered across Resistor R9( in parallel with R9) and C2 should be soldered across Resistor R10.
Base design
