Detector Description

GEM Detector Design and Structure

You should first describe the basics of the gas electron multiplier  then describe the ionization chamber equipped with GEM foils, then describe the assembly in a clean room environment.

The GEM preamplifier described in section XXXX was used to increase the signal amplitude of the ionization chamber. The strong electric fields of the GEM foils cause secondary ionization as the primary ionization event is transported towards the cathode. A single GEM preamplifier attains an electron multiplication up to [math]10^3 [/math], on the other hand, Adding a rim of 10um for each hole and increasing the number of cards to three GEM cards increase the multiplication to [math]10^4-10^5 [/math]. In the detector chamber, three GEM cards have been installed to provide multiplication that raise the signal amplitude over the noise level at relatively low voltage applied between the top and bottom side of each GEM preamplifier.

Detector Structure

You should describe the features of the detector using a paragraph and not an enumerated list.

 First start with a description of the GEM foil and how the strong electric fields cause secondary ionization

After that you describe using several of the foils to further multiply the signal and introduce the anode and cathode to direct ionized electrons through the three amplification stages.

 Finally you can describe the HV network used to supply a voltage to all the components and the ionization chamber which immerses them in the Ar/Co2 gas.

The triple GEM detector is based on three GEM preamplifiers, a cathode and an anode. The GEM preamplifier is made of a copper-clad kipton plate which is 50 um thick and has an area of 10x10cm, it has holes that are chemically etched with a diameter of 50 um with a 10um rim. The holes have a an equilateral triangular pattern with a 140 um pitch distance. The detector possesses three GEM cards in square plastic frames, they are placed parallel to the cathode and are separated by a vertical distance of 2.8 mm as shown in the figure below.

Fig.1 shows the original GEM detector design.

The cathode is a square copper plate that is a 10x10cm and has a distance of 3.5 mm from the top of the first GEM card. This cathode design allows a rise in potential on its surface up to 5 kV (in the air) without any discharge effect.The charge collector (readout anode) is constructed of 50-80 micron wide strips and are insulated to determine the location of the collected electrons. They are arranged to give equal charge sharing on the charge collector.

Fig. shows the charge collector wire's dimensions and arrangement.

All the previous components exist in a sealed chamber that consists of two ertalyte plastic sheets; they are bolted together by a number of M3 plastic screws located around the detector window to form a well enclosed cavity. Also, the chamber has a 13x13cm kipton window for incident particles.The figures below show top, bottom and side view of the detector's chamber design.

Modifying the GEM detector as neutron sensitive detector

The GEM’s original design was modified to convert it to a neutron sensitive detector. The cathode design has a 3 cm diameter coating, and 40-50 um thickness. The kepton window had an increase in height of 2.5 mm, which helped to increase the distance of the cathode to 8 mm from the top of the first of GEM card (instead of 3.5 mm in the original design). An FR4 shutter was attached in the space between the cathode and the first GEM card, which had enough area to cover the coating area; it has a position controller that helps to open and close the shutter. When the shutter is closed, it covers the U-233 coating and stops the emitted fission fragments from causing ionization in the gas, but when the shutter is open, the ionization of the fission fragments produces a signal that indicates the existence of neutrons inside the chamber which the detector trigger detects for analysis by the DAQ system.

The figures below show the modified components of the detector.

Adding modifications to GEM design.	Modifying the cavity size by the increasing the height of kapton window.
Detector's shutter is open.	Detector's shutter is close.

High voltage divider circuit

GEM preamplifiers are connected with high voltage divider circuit. as shown in the figure below:

The circuit provides the cathode with a voltage of 3.6 kV, and it produces an electric field which drifts most of the electrons that are primarily produced by ionization. The circuit also provides the GEM preamplifiers with voltage between the top and bottom of each card; the voltage gradually decreases to have the least value between the sides of the third GEM card. This design's advantage is to provide enough voltage for electron multiplication, and to guide most of the drift electrons to the grounded readout plate.

The following table shows the voltage measurements between the sides of the GEM preamplifiers, and voltage between each side and the ground using the HV-voltage divider circuit shown in figure (2).

[math] V_{source} \pm 1 [/math]	[math] V_{G1T} \pm 1 [/math]	[math] V_{G1B} \pm 1 [/math]	[math] \Delta V_1 \pm 1 [/math]	[math] V_{G2T} \pm 1 [/math]	[math] V_{G2B} \pm 1 [/math]	[math] \Delta V_2 \pm 1[/math]	[math] V_{G3T} \pm 1 [/math]	[math] V_{G3B} \pm 1 [/math]	[math] \Delta V_3 \pm 1 [/math]
2550	2579	2259	304	1671	1394	279	818	570	245
2600	2630	2303	310	1704	1421	285	834	581	250
2650	2680	2348	316	1737	1449	290	850	592	255
2700	2731	2393	322	1770	1476	296	866	603	260
2750	2781	2373	328	1803	1503	302	882	614	264
2800	2832	2482	332	1836	1530	307	898	625	269

<references/>

Go Back [1]