DDP:Detailed Design Phase: Drawing and Assembly Package

From New IAC Wiki
Jump to navigation Jump to search

Detailed Design Drawing Report 6/27/08

Outline:

1.) Dimensions

2.) Constraints: Case 3 from progress report: constrain triangle and nose plate on upstream side.

3.) Deflection Analysis

Steps:

a.) check triangle contact region and its mass b.) add another carbon fiber rod c.) increase size of back plate


4.) Drawings

drawings in PDF format

a.) Endplate structural drawing (no holes just shaded area)

b.) Drawings for all other parts

c.)

d.) Copy old R3 (take advantage of no curved window.

26jun08 01.png

Report

Introduction

Initial parameters to be followed to fulfill to satisfy design Criteria

1. Distance from target to first sense wire plane along a ray which is normal to the end plate = 4746.5 mm

2. Chamber Tilt Angle = 25 Degrees

3. Maximum Scattering Angle = 45.05 Degrees

4. Minimum Scattering Angle = 4.5 Degrees

5. Wires are at 6 Degrees to the horizontal in each of its wire planes


Jun20 2008 1.png Jun20 2008 2.png Jun20 2008 3.png

Assembly

The Assembly of each sector in the region 3 drift chamber can be considered similar to each other. Each assembly can be divided into sub-assemblies like

1. Nose Plate

2. Left End Plate

3. Right End plate

4. Back plate

5. Backing Sheet

6. Carbon rods

7. Attachments: These are the external geometric parts of each sector, used for clamping and mounting each sector. so, they might change with the orientation of each sector

R3BreakOutDiagram.jpg

A detailed drawing of this Basic sector assmebly can be viewed at File:B00000-01-10-0001.pdf


Nose Plate

Nose plate is the plate where both the end plates are attached to it on either side

Assembly20 jun 1.png

A detailed drawing of Nose plate can be viewed at File:B00000-01-10-0002.pdf

Left End Plate

Left end plate is the end plate to the left hand side if we are viewing from the target. Left end plate and the right end plate are same with parts and its dimensions. However, the hole locations differ between each other.

Assembly20 jun 2.png

Each end plate sub assembly consists of 3 parts, namely

End plate casing - Made of Aluminum.

Assembly20 jun 5.png


They can be referenced with left and right to show each sub assembly.

A detailed drawing of Left end plate Core can be viewed at File:B00000-01-10-0003.pdf

A detailed drawing of Left end plate skin can be viewed at File:B00000-01-10-0004.pdf

Since end plate casing will not have holes for wires, the drawing for left end plate casing and right end plate casing will be the same.

A detailed drawing of Left end plate casing can be viewed at File:B00000-01-10-0005.pdf


Back Plate

Back plate is the plate which connects the left end plate and right end plate on the top.

Assembly20 jun 10.png

Back plate sub assembly consists of 3 parts, namely

Back plate Core - made of Polyurethane

Assembly20 jun 11.png

Back plate Skins - 2 No's- Made of stainless steel

Assembly20 jun 12.png

Back plate casing - Made of Aluminum

Assembly20 jun 13.png

A detailed drawing of back plate Core can be viewed at File:Assembly20 jun 11.pdf

A detailed drawing of back plate skin can be viewed at File:Assembly20 jun 12.pdf

A detailed drawing of back plate casing can be viewed at File:Assembly20 jun 13.pdf

Backing Sheet

Backing sheet is the large sheet which is mounted on the downstream side of sector.

Assembly20 jun 14.png

It consists of 2 parts, namely

Hexcel Core and Carbon fiber skins on either side

A detailed drawing of back plate Core can be viewed at File:Assembly20 jun 14.pdf

A detailed drawing of back plate skin can be viewed at File:Assembly20 jun 15.pdf


Carbon fiber rods

These rods are mounted on the upstream side of each sector, connecting the left end plate aluminum casing and right end plate aluminum casing..

Assembly20 jun 15.png

There are 6 Carbon rods each of outer diameter of 50.8 mm and inner diameter of 48.26mm

A detailed drawing of carbon fiber rods can be viewed at File:Assembly20 jun 16.pdf


Go Back