CH He3 Attenuation Measurements Revisited

From New IAC Wiki
Revision as of 15:18, 24 February 2022 by Harpconn (talk | contribs) (Undo revision 128450 by Harpconn (talk))
Jump to navigation Jump to search

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

He3 Tube Plateau

Measurements

1250V Source Out Data
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz)
1 Detector on 3D printed stands at +1250V 125 No 100
2 Detector on 3D printed stands at +1250V 145 No 100
3 Detector on 3D printed stands at +1250V 155 No 100
4 Detector on 3D printed stands at +1250V 160 No 100
5 Detector on 3D printed stands at +1250V 165 No 100
6 Detector on 3D printed stands at +1250V 170 No 100
7 Detector on 3D printed stands at +1250V 175 No 100
8 Detector on 3D printed stands at +1250V 185 No 100
9 Detector on 3D printed stands at +1250V 205 No 100
10 Detector on 3D printed stands at +1250V 225 No 100
11 Detector on 3D printed stands at +1250V 245 No 100
12 Detector on 3D printed stands at +1250V 255 No 100
1250V Source In Data
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz)
1 Detector on 3D printed stands at +1250V 125 Yes 100
2 Detector on 3D printed stands at +1250V 145 Yes 100
3 Detector on 3D printed stands at +1250V 155 Yes 100
4 Detector on 3D printed stands at +1250V 160 Yes 100
5 Detector on 3D printed stands at +1250V 165 Yes 100
6 Detector on 3D printed stands at +1250V 170 Yes 100
7 Detector on 3D printed stands at +1250V 175 Yes 100
8 Detector on 3D printed stands at +1250V 185 Yes 100
9 Detector on 3D printed stands at +1250V 205 Yes 100
10 Detector on 3D printed stands at +1250V 225 Yes 100
11 Detector on 3D printed stands at +1250V 245 Yes 100
12 Detector on 3D printed stands at +1250V 255 Yes 100
Plateau Plots
Plateau measurements at 700V, source in and source out overlaid.
Plateau measurements at 700V, source in minus source out.
Signal to Noise ratio for 700V at different discriminator voltages

Repeat of Initial Experimental Setup #1

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

CAEN Discriminator Model N841 Tag #113

  • 255mV threshold
  • Pulse width as measured on scope: 43ns

Ortec Spec Amp Model 672

  • 10x Course Gain
  • 1x Fine Gain
  • 2us Shaping Time
  • Uni Shaping: Gaussian
  • Input: Norm (-)
  • Output: Unipolar

Dual Timer

  • Discriminator output used to start timer
  • Timer output used to trigger scalar
  • Pulse width as measured on scope: 100ns

Scope Images

Background Measurements

2/24/22 ~7:30am

1250V Background Measurements
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 No 43 100
2 Detector on 3D printed stands at +1250V 255 No 47 100
3 Detector on 3D printed stands at +1250V 255 No 50 100
4 Detector on 3D printed stands at +1250V 255 No 54 100
5 Detector on 3D printed stands at +1250V 255 No 50 100

Attenuation Measurements

Open Source

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

2" Green poly (one brick) no thermalizer

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

3" Green poly (one brick & sheet)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

4" Green poly (two bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

6" Green poly (three bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

8" Green poly (four bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

Repeat of Initial Experimental Setup #2

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

CAEN Discriminator Model N841 Tag #115

  • 255mV threshold
  • Pulse width as measured on scope:

Ortec Spec Amp Model 672

  • 10x Course Gain
  • 1x Fine Gain
  • 2us Shaping Time
  • Uni Shaping: Gaussian
  • Input: Norm (-)
  • Output: Unipolar

Dual Timer

  • Discriminator output used to start timer
  • Timer output used to trigger scalar
  • Pulse width as measured on scope: 100ns

Scope Images

Background Measurements

2/24/22 ~7:30am

1250V Background Measurements
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on poly at +1250V 255 No 43 100
2 Detector on poly at +1250V 255 No 47 100
3 Detector on poly at +1250V 255 No 50 100
4 Detector on poly at +1250V 255 No 54 100
5 Detector on poly at +1250V 255 No 50 100

Attenuation Measurements

1" Green poly

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

2" Green poly (one brick) no thermalizer

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

3" Green poly (one brick & sheet)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

4" Green poly (two bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

6" Green poly (three bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

8" Green poly (four bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

Attenuation Experiment using HPGe Lynx System as PSU/DAQ

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

Measurements

Attenuation Experiment using New Modules in Electronics Chain

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

Lecroy Discriminator Model 821

  • 255mV threshold
  • Pulse width as measured on scope: 20ns

Ortec Spec Amp Model 672

  • 10x Course Gain
  • 1x Fine Gain
  • 2us Shaping Time
  • Uni Shaping: Gaussian
  • Input: Norm (-)
  • Output: Unipolar

Dual Timer

  • Discriminator output used to start timer
  • Timer output used to trigger scalar
  • Pulse width as measured on scope: 100ns

Scope Images

  • Purple: CAEN Dual Timer using Lecroy Disc as input. 100ns pulse width. Aqua: Lecroy Disc Output. 20ns pulse width.

  • Purple: CAEN Dual Timer using Lecroy Disc as input. 100ns pulse width. Aqua: Lecroy Disc Output. 20ns pulse width. Lime:: Ortec Spec Amp 672 output.

Background Measurements

2/23/22 ~4pm

1250V Background Measurements
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 No 63 100
2 Detector on 3D printed stands at +1250V 255 No 52 100
3 Detector on 3D printed stands at +1250V 255 No 65 100
4 Detector on 3D printed stands at +1250V 255 No 53 100
5 Detector on 3D printed stands at +1250V 255 No 70 100

2/24/22 ~7:30am

1250V Background Measurements
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 No 59 100
2 Detector on 3D printed stands at +1250V 255 No 41 100
3 Detector on 3D printed stands at +1250V 255 No 57 100
4 Detector on 3D printed stands at +1250V 255 No 56 100
5 Detector on 3D printed stands at +1250V 255 No 55 100

Attenuation Measurements

Open Source

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 5835 100
2 Detector on 3D printed stands at +1250V 255 Yes 5730 100
3 Detector on 3D printed stands at +1250V 255 Yes 5801 100
4 Detector on 3D printed stands at +1250V 255 Yes 5913 100
5 Detector on 3D printed stands at +1250V 255 Yes 5837 100

2" Green poly (one brick)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 1160 100
2 Detector on 3D printed stands at +1250V 255 Yes 1110 100
3 Detector on 3D printed stands at +1250V 255 Yes 1087 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

3" Green poly (one brick & sheet)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

4" Green poly (two bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

6" Green poly (three bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100

8" Green poly (four bricks)

1250V source in
Run Number Configuration Discriminator Threshold (mV) Cf-252 Source Counts Run Time (Sec) Count Rate (Hz) Uncertainty
1 Detector on 3D printed stands at +1250V 255 Yes 100
2 Detector on 3D printed stands at +1250V 255 Yes 100
3 Detector on 3D printed stands at +1250V 255 Yes 100
4 Detector on 3D printed stands at +1250V 255 Yes 100
5 Detector on 3D printed stands at +1250V 255 Yes 100


Previous Page

CaGaS Phase II

Retrieved from "https://wiki.iac.isu.edu/index.php?title=CH_He3_Attenuation_Measurements_Revisited&oldid=128451"