IAC runs

ADC is connected,

Beam On: run 5496 as the detector is on 13:31:11 13:47:18 run 5497 as the detector is off 13:52:51

Run Number	Beam	Start Time	End time	Notes
5496	on	13:31:11	13:47:18	Detector is in operating voltage.
5497	on	13:52: 51		Detector is in off mode
5515	off	5:59: 46	6:27:43	Detector is in operating voltage.
5516	off	6:29:32	06:38:13	Detector is in off mode
5517	off	6:43:42	06:50:05	shutter is close
5518	off	06:55:59	07:06:57	Detector is in operating voltage.
5519	on	07:56:53		Detector is in operating voltage.
5520,21,22	on	09:38:36		Detector is in operating voltage.
5523	on	9:51:00	10:13:38	Detector is in operating voltage.
5524	on	10:14:35		PMT is added to ADC ch#14
5526	on	11:51:35	12:02:49	PMT TDC ch#0 GEM ch#2 ADC ch# 12 GEM Ch#14 PMT
5528	on	12:21:28	13:35:26
5529	on	13:36:28	14:44:37
5530	on	14:45:24	15:09:16
5531	on	15:09:41	15:20:03
5532	on	15:23:31	15:31:00
5532	on	15:23:31	16:04:31
5532	on	16:05:00	16:04:31
5537	on	16:22:00	16:27:03
5541	on	16:42:02	16:27:03

All the previous runs has a positive input to the ADC.

Run Number	Beam	Start Time	End time	Notes
5593	on	15:55:04	16:29:20	stable beam to the end of the run.
5594	on	16:36:19	17:03:52	stable beam to the end of the run.
5595	on	08:28:09	08:45:19	stable beam to the end of the run.
5596	on	08:47:16	10:06:37	stable beam to the end of the run.
5603	on but trasfered	13:31:30	14:38:02	shutter is close

- Detector voltage is 2300, 2800V GEM and Cathode successively. GEM has not any output to the TDC for 5773, 5774.

Run Number	Beam	Start Time	End time	Notes
5773	on			beam on for 4-10s, overflow
5774	on			beam on for 4-10s shutter is close, beam energy is 7.5 MeV
5775	on			beam on for 4-10s shutter is open, beam energy is 7.5 MeV
5776	on			beam on for 4-10s shutter is open, beam energy is 7.5 MeV
5777	on			beam on for 4-10s shutter is close, beam energy is 7.5 MeV
5778	off	19:54:17	6:00:00	shutter is close 2.8, 3.4 G/C, Amp.6_6
5779	off	6:05:33		shutter is open 2.8, 3.4 G/C, Amp.6_6

09/01/13

Detector voltage is 2.8, 3.4 kV for cathode and GEM.

Run Number		Amp level	discriminator level	Notes
5925	50, 4	3.6	shutter close
5926	50, 4	3.6	shutter open
5927	100	3.6	shutter open
5928	200	3.6	shutter open, high amp level
5929	100, 10	3.6	shutter open high amp level
5930	100, 7	3.6	shutter open
5936	100, 7	0.1	shutter open, noise peak channel 74
5937	100, 7	0.1	shutter open, V_cath = V_GEM,noise peak channel 74
5948	100, 7	1.15	shutter open, detector is on, no signal overlapping, reached to te signal highest rate, with almost 100% signal to noise ratio.

The following run has the same setting as the last run, unless there is achange written in the notes.

Run Number	start time	end time	shutter	Notes
5948	14:22:14	14:36:09	open
5949	15:02:43	15:19:59	open
5950	15:20:42	15:35:07	open	r5951 and r5952 has the shutter close and integrate 1
5953	16:37:03	15:35:07	close	integrate lower from 1 to 0.5,sthg strange happened, root does not show a picture and the rate increased suddenly to 450 Hz
5957	09:01:07	09:25:12	open	integrate 0.5
5959	09:30:21	09:55:15	close	integrate 1

Run Number	start time	end time	shutter	Notes
5972	:52:15		open

Run Number	start time	end time	shutter	Notes
5954	16:55:52	08:44:23 N	close	integrate 1 rate changed from 1.2 Hz to 57 Hz due to increase the noise level overnight only.
5966	12:44:21	19:15:35	open