General info on IAC NaI detector

[[1]]

Crystal size

NaI crystal sizes: 3”x3”

PMT base configureation

IAC NAI_0

analysis commands

/home/daq/CODA/CODAreader/UsingROOTnEVIO/Oleksiy/evio2nt -fr2177.dat > /dev/null

mv r2177 r2177.root

root r2177.root

TH1F * Hist1=new TH1F("Hist1","Hist1",4096,-0.5,4095.5);

ntuple->Draw("ADC1 >> Hist1")

Run Number	Source	Running Time (sec)	HV (Volts)	Disc. Thresh (mV)	Integrate Gate ([math]\mu[/math] s)	Anode Histogram
2178
2179	Cosmic	18 h 4 min 07 s	634	26	0.8
2180	Cosmic	18 min 37 s	661	26	0.8
2182	Cosmic	19 min 21 s	690	26	0.8
2183	Cosmic + Na22	22 min 44 s	690	26	0.8
2192	Cosmic + Na22	51 s	995	24	2
2193	Cosmic	18 h 3 min 12 s	995	24	2
2194	Cosmic + Co60	35	995	24	2
2196	Cosmic + Co60	8 min 55 s	900	24	2
2197	Cosmic + Na22	6 min 35	900	24	2
2199	Cosmic + Co60	1 h 1 min 52 s	800	24	2
2200	Cosmic + Na22	45 min 23 s	800	24	2
2201	Cosmic + Na22	2 min 55 s	800	4	2
2202	Cosmic + Na22	1 min 45 s	900	4	2
2204	Cosmic + Na22	6 min 47 s	700	0	2
2205	Cosmic + Na22	3 min 9 s	1000	30	2
2206	Cosmic + Co60	min s	1000	30	2
2208	Cosmic + Co60	1 min 27 s	1050	20	2
2209	Cosmic + Na22	115 s	1050	20	2
2210	Cosmic + Na22	77 s	1050	10	2
2211	Cosmic + Co60	153 s	1050	10	2
2212	Cosmic + Co60	34 s	1050	0	2
2213	Cosmic + Na22	119 s	1050	0	2
2214	Cosmic	22 h 15 min 49 s	1050	0	2
2215	Co60	s	1075	10	2

Detector and Parts

Big pulse due to scope 1 M ohm scope resistance

Pulses in the following to detectors are huge due to we used wrong scope resistance of 1 M ohm.

IAC NAI_1

Without Mu material:

HV = 700 V

With Mu material:

HV = 700 V

IAC_NAI_2

With Mu material

HV = 700 V

Tests with 50 Ohm Scope Resistance

All the following tests are done under 700 V.

IAC NAI_1 with Base #1

Detector # 1 with Base #1:

IAC NAI_2 with Base #2

Detector # 2 with Base #2:

IAC NAI_3 with Base #3

Detector # 3 with Base #3:

IAC NAI_4 with Base #4

Detector # 4 with Base #4:

Calibration

Starting CODA

Starting

Do it at 7 different terminal.

Need to do command on all of them:

source CODA/setup

1st Terminal

msqld

2nd Terminal

telnet roc1

Check if connected by "ls" command, see if you can see libraries there.

load 2 Libraries:

ld < v775Lib.o

ld < v792Lib.o

telnet: connect to address 10.1.1.2: Connection refused

Turn off Firewall

As super users execute:

/sbin/service iptables stop

telnet: connect to address 10.1.1.2: No route to host

Restart roc1, first by turning off small pushing button, then by red button on the top.

Sorry, session limit reached. Connection closed by foreign host

Restart.

3rd Terminal

et_start -v -s 70000 -n 200

4th Terminal

rcServer

5th Terminal

coda_eb -i -s DAQ -n eb1 -t CDEB

6th Terminal

coda_er -i -s DAQ -n LDS_ER -t ROC

7th Terminal

runcontrol

1st Attempt - Failed

1.msqld

~ >source CODA/setup

~ >msqld

mSQL Server 1.0.16coda starting ...

Can't start server : IP Bind : Address already in use

~ >

Ignore

telnet roc1

~ >source CODA/setup

~ >telnet roc1

Trying 10.1.1.2...

telnet: connect to address 10.1.1.2: No route to host

~ >

Restart roc1, first by turning off small pushing button, then by red button on the top.

et_start

~ >cource CODA/setup

cource: Command not found.

~ >source CODA/setup

~ >et_start -v -s 70000 -n 200

et_start: asking for 70000 byte events.

et_start: asking for 200 events.

et_start: starting ET system /tmp/et_sys_DAQ

et ERROR: et_system_start, ET system process already exists!

et_start: error in starting ET system

~ >rm /tmp/et_sys_DAQ

~ >et_start -v -s 70000 -n 200

et_start: asking for 70000 byte events.

et_start: asking for 200 events.

et_start: starting ET system /tmp/et_sys_DAQ

need to delete the old memory file /tmp/et_sys_DAQ

rcServer

~ >source CODA/setup

~ >rcServer

Listening for UDP on port 2052

sh: cmlog_activate: command not found

run control up and running!!

daLogMsg: run control up and running!!

coda_eb

~ >source CODA/setup

~ >coda_eb -i -s DAQ -n eb1 -t CDEB

CODA 2.5,Name : eb1, Type CDEB Id : 0

sh: cmlog_activate: command not found

"eb1" state now "booted"

daLogMsg: "eb1" state now "booted"

DAQ::eb1>

coda_er

~ >source CODA/setup

~ >coda_er -i -s DAQ -n LDS_ER -t ROC

CODA 2.5,Name : LDS_ER, Type ER Id : 0

sh: cmlog_activate: command not found

"LDS_ER" state now "booted"

daLogMsg: "LDS_ER" state now "booted"

DAQ::LDS_ER>

runcontrol

~ >source CODA/setup

~ >runcontrol

sh: uncompress: command not found

Run Control Interface

1st Attempt

Then Run control interface appears.

1. Press "Connect"

2. Press "Configure" (on the top middle)

Then "Run Type Configuration" appears

3. Select "SIS3610", Press "OK"

4. Press "Configure" again.

5. Select "V792_ADC", Press "OK"

6 Press "Download"

Followings are the messeges

INFO : runNumber is now: 2569

INFO : Run number is 2569

INFO : Parsing SIS3610 configuration

INFO : activate component roc1

INFO : activate component eb1

INFO : activate component LDS_ER

INFO : activate component coda_0

INFO : Parsing SIS3610 finished

WARN : No data count limit

WARN : No event count limit

INFO : transition Configure succeeded.

INFO : runNumber is now: 2569

INFO : Run number is 2569

INFO : Configuration V792_ADC is already in use.

INFO : Parsing V792_ADC configuration

INFO : activate component roc1

INFO : activate component eb1

INFO : activate component LDS_ER

INFO : activate component coda_0

INFO : Parsing V792_ADC finished

WARN : No data count limit

WARN : No event count limit

INFO : transition Configure succeeded.

INFO : Connecting to LDS_ER on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to eb1 on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to roc1 on host roc1

Then it stopped.

2nd Attempt

Then Run control interface appears.

1. Press "Connect"

2. Press "Configure" (on the top middle)

Then "Run Type Configuration" appears

3. Select "SIS3610", Press "OK"

4. Press "Configure" again.

5. Select "V792_ADC", Press "OK"

6 Press "Start Run"

INFO : Parsing V792_ADC finished

WARN : No data count limit

WARN : No event count limit

INFO : transition Configure succeeded.

INFO : Connecting to LDS_ER on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to eb1 on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to roc1 on host roc1

Then it stopped again.

3rd Attempt

Then Run control interface appears.

1. Press "Connect"

2. Press "Configure" (on the top middle)

Then "Run Type Configuration" appears

3. Select "V792_ADC", Press "OK"

4. Press "Start Run"

INFO : transition Configure succeeded.

INFO : Connecting to LDS_ER on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to eb1 on host daq1.physics.isu.edu

INFO : booted ok

INFO : Connecting to roc1 on host roc1

Then it stopped.

Second Attempt to Start CODA

msqld

~ >source CODA/setup

~ >msqld

mSQL Server 1.0.16coda starting ...

Can't start server : IP Bind : Address already in use

Need to kill the process

ps -aux | grep msqld

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ
daq       7724  0.0  0.0   2216   828 ?        S    Sep26   0:00 msqld
daq      23620  0.0  0.0   3912   684 pts/0    R+   14:12   0:00 grep msqld

~ >kill -9 7724

~ >msqld

mSQL Server 1.0.16coda starting ...

setjmp returned 0

Checking Authority to use databases in /usr/local/coda/common/rcdb

loading administration ACL msql.acl

admin ACL loaded

loading ACL for database LDS.back

Warning : Couldn't open ACL file: No such file or directory

database LDS.back ACL loaded.

loading ACL for database LDS

Warning : Couldn't open ACL file: No such file or directory

database LDS ACL loaded.

loading ACL for database LDS.back1

Warning : Couldn't open ACL file: No such file or directory

database LDS.back1 ACL loaded.

ACL load done

telnet roc1

~ >source CODA/setup

~ >telnet roc1

Trying 10.1.1.2...

Connected to roc1.

Escape character is '^]'.

->

et_start

~ >source CODA/setup

~ >et_start -v -s 70000 -n 200

et_start: asking for 70000 byte events.

et_start: asking for 200 events.

et_start: starting ET system /tmp/et_sys_DAQ

et ERROR: et_system_start, ET system process already exists!

et_start: error in starting ET system

~ >rm /tmp/et_sys_DAQ

~ >et_start -v -s 70000 -n 200

et_start: asking for 70000 byte events.

et_start: asking for 200 events.

et_start: starting ET system /tmp/et_sys_DAQ

rcServer

~ >source CODA/setup

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23886 0.0 0.0 3912 692 pts/20 S+ 14:39 0:00 grep rcServer

~ >rcServer

Warning: RunControl Server: DAQ may be running already

Info: RunControl Server DAQ is not running on port 2052

Listening for UDP on port 2052

sh: cmlog_activate: command not found

run control up and running!!

daLogMsg: run control up and running!!

tried to kill them

~ >source CODA/setup

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23969 0.0 0.0 3912 696 pts/20 S+ 14:43 0:00 grep rcServer

~ >kill -9 23969

23969: No such process

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23972 0.0 0.0 3912 692 pts/20 S+ 14:43 0:00 grep rcServer

~ >kill 23969

23969: No such process

~ >kill -9 23972

23972: No such process

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23976 0.0 0.0 3912 696 pts/20 S+ 14:44 0:00 grep rcServer

~ >kill -9 23976

23976: No such process

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23978 0.0 0.0 3912 696 pts/20 S+ 14:44 0:00 grep rcServer

~ >kill -9 23978

23978: No such process

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

daq 23980 0.0 0.0 3912 716 pts/20 R+ 14:44 0:00 grep rcServer

~ >kill -9 23980

23980: No such process

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

~ >ps -aux | grep rcServer

Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ

~ >rcServer

Warning: RunControl Server: DAQ may be running already

Info: RunControl Server DAQ is not running on port 2052

Listening for UDP on port 2052

sh: cmlog_activate: command not found

run control up and running!!

daLogMsg: run control up and running!!

coda_eb

~ >cource CODA/setup

cource: Command not found.

~ >source CODA/setup

~ >coda_eb -i -s DAQ -n eb1 -t CDEB

CODA 2.5,Name : eb1, Type CDEB Id : 0

sh: cmlog_activate: command not found

"eb1" state now "booted"

daLogMsg: "eb1" state now "booted"

DAQ::eb1>

coda_er

~ >source CODA/setup

~ >coda_er -i -s DAQ -n LDS_ER -t ROC

CODA 2.5,Name : LDS_ER, Type ER Id : 0

sh: cmlog_activate: command not found

"LDS_ER" state now "booted"

daLogMsg: "LDS_ER" state now "booted"

DAQ::LDS_ER>

runcontrol

~ >source CODA/setup

~ > runcontrol

Run Control Interface

1. connect

2. Configure

3. Select V792_ADC

4. at "REad From" select "roc1"

5. Configure

6. Download

Then stopped.

Dr. Forest looked all the terminals and said all of them are resdponding except roc1

He restarted roc1, Then followings are what he had done

~ >source CODA/setup

~ >msqld

mSQL Server 1.0.16coda starting ...

Can't start server : IP Bind : Address already in use

~ >telnet roc1

Trying 10.1.1.2...

Connected to roc1.

Escape character is '^]'.

-> -> -> -> telnet> ^[[A^[[B

?Invalid command

telnet> quit

Connection closed.

~ >telnet roc1

Trying 10.1.1.2...

Connected to roc1.

Escape character is '^]'.

telnetd: This system *IN USE* via telnet.

shell restarted.

-> shell restarted.

-> reboot

telnet> quit

Connection closed.

~ >telnet roc1

Trying 10.1.1.2...

^]^] ~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=1 Destination Host Unreachable

--- roc1.physics.isu.edu ping statistics ---

4 packets transmitted, 0 received, +1 errors, 100% packet loss, time 2999ms

~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=3 Destination Host Unreachable

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=4 Destination Host Unreachable

--- roc1.physics.isu.edu ping statistics ---

7 packets transmitted, 0 received, +2 errors, 100% packet loss, time 5998ms

, pipe 2

~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=2 Destination Host Unreachable

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=3 Destination Host Unreachable

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=4 Destination Host Unreachable

--- roc1.physics.isu.edu ping statistics ---

5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3999ms

, pipe 3

~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

--- roc1.physics.isu.edu ping statistics ---

13 packets transmitted, 0 received, 100% packet loss, time 11998ms

~ >who

daq tty1 2011-09-25 19:20

daq pts/0 2011-10-14 14:22 (:0.0)

daq pts/1 2011-10-14 14:20 (:0.0)

daq pts/3 2011-10-14 14:22 (:0.0)

daq pts/7 2011-09-28 16:58 (winnebago.iac.isu.edu)

daq pts/8 2011-10-05 09:38 (:0.0)

daq pts/9 2011-10-10 10:17 (:0.0)

daq pts/10 2011-10-05 10:05 (:0.0)

daq pts/11 2011-10-05 11:33 (:0.0)

daq pts/12 2011-10-05 11:20 (:0.0)

daq pts/13 2011-10-07 13:55 (:0.0)

daq pts/14 2011-10-10 12:47 (134.50.3.21)

daq pts/15 2011-10-12 10:58 (134.50.203.192)

daq pts/16 2011-10-10 10:33 (:0.0)

daq pts/17 2011-10-12 12:28 (134.50.203.192)

daq pts/18 2011-10-10 10:50 (:0.0)

daq pts/20 2011-10-14 14:42 (:0.0)

daq pts/21 2011-10-14 14:47 (:0.0)

daq pts/22 2011-10-14 14:49 (:0.0)

daq pts/23 2011-10-14 14:49 (:0.0)

daq pts/24 2011-10-14 15:03 (:0.0)

daq pts/25 2011-10-14 15:14 (:0.0)

daq pts/26 2011-10-14 15:16 (:0.0)

daq pts/27 2011-10-14 15:17 (:0.0)

daq pts/28 2011-10-14 15:18 (:0.0)

daq pts/29 2011-10-14 15:26 (:0.0)

daq pts/30 2011-10-14 15:42 (:0.0)

~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

From localdaq.physics.isu.edu (10.1.1.1) icmp_seq=10 Destination Host Unreachable

--- roc1.physics.isu.edu ping statistics ---

19 packets transmitted, 0 received, +6 errors, 100% packet loss, time 17998ms

, pipe 3

~ >ping roc1

PING roc1.physics.isu.edu (10.1.1.2) 56(84) bytes of data.

64 bytes from roc1.physics.isu.edu (10.1.1.2): icmp_seq=1 ttl=64 time=0.125 ms

64 bytes from roc1.physics.isu.edu (10.1.1.2): icmp_seq=2 ttl=64 time=0.277 ms

64 bytes from roc1.physics.isu.edu (10.1.1.2): icmp_seq=3 ttl=64 time=0.199 ms

64 bytes from roc1.physics.isu.edu (10.1.1.2): icmp_seq=4 ttl=64 time=0.086 ms

64 bytes from roc1.physics.isu.edu (10.1.1.2): icmp_seq=5 ttl=64 time=0.225 ms

--- roc1.physics.isu.edu ping statistics ---

5 packets transmitted, 5 received, 0% packet loss, time 3999ms

rtt min/avg/max/mdev = 0.086/0.182/0.277/0.069 ms

~ >telnet roc1

Trying 10.1.1.2...

Connected to roc1.

Escape character is '^]'.

-> ls

.

..

1

bin1.bin

dmaPLib.o

fadcLib.o

fadcMolLib.o

faSetProcMode

GEMReadout_31MHz_Rev4_1_Test.rbf

GEMReadout_32Mhz_Rev4.rbf

GEMReadout_40Mhz_Rev4_1.rbf

GEMReadout_40Mhz_Rev4.rbf

GEMReadout_NoPLL_Rev4.rbf

sis3610Lib.o

universeDma.h

universeDma.o

universeDma.o.5100

universeDma.o.vw54

usrTempeDma.o

v1495Lib.o

v260_bak.o

v260Lib.o

v775Lib.o

v775Lib.o.bak

v792_dmaLib.o

v792Lib.o

v792Lib.o.bak

value = 0 = 0x0

-> ld < v775Lib.o

Undefined symbol: sysVmeDmaSend (binding 1 type 0)

Undefined symbol: sysVmeDmaDone (binding 1 type 0)

ld error: Module contains undefined symbol(s) and may be unusable.

value = 0 = 0x0

-> ld < v792Lib.o

Undefined symbol: sysVmeDmaSend (binding 1 type 0)

Undefined symbol: sysVmeDmaDone (binding 1 type 0)

ld error: Module contains undefined symbol(s) and may be unusable.

value = 0 = 0x0

->

Then he looked at runcontrol and said he has no other solution than to restart daq computer (local host) for error "Cannot open broadcast Handler"

~ >runcontrol

sh: uncompress: command not found

Warning: RunControl Server: DAQ may be running already

Info: RunControl Server DAQ is not running on port 2052

Cannot open broadcast Handler

But Tamuna is transferring data, so I am going to do it later.

Third Attempt to Start CODA

msqld

~ >source CODA/setup

~ >msqld

mSQL Server 1.0.16coda starting ...

setjmp returned 0

Checking Authority to use databases in /usr/local/coda/common/rcdb

loading administration ACL msql.acl

admin ACL loaded

loading ACL for database LDS.back

Warning : Couldn't open ACL file: No such file or directory

database LDS.back ACL loaded.

loading ACL for database LDS

Warning : Couldn't open ACL file: No such file or directory

database LDS ACL loaded.

loading ACL for database LDS.back1

Warning : Couldn't open ACL file: No such file or directory

database LDS.back1 ACL loaded.

ACL load done

telnet roc1

~ >source CODA/setup

~ >telnet roc1

Trying 10.1.1.2...

Connected to roc1.

Escape character is '^]'.

->

et_start

~ >source CODA/setup

~ >et_start -v -s 70000 -n 200

et_start: asking for 70000 byte events.

et_start: asking for 200 events.

et_start: starting ET system /tmp/et_sys_DAQ

Segmentation fault

~ >

rcServer

~ >source CODA/setup

~ >rcServer

Listening for UDP on port 2052

sh: cmlog_activate: command not found

run control up and running!!

daLogMsg: run control up and running!!

coda_eb

~ >source CODA/setup

~ >coda_eb -i -s DAQ -n eb1 -t CDEB

CODA 2.5,Name : eb1, Type CDEB Id : 0

sh: cmlog_activate: command not found

"eb1" state now "booted"

daLogMsg: "eb1" state now "booted"

DAQ::eb1>

coda_er

~ >source CODA/setup

~ >coda_er -i -s DAQ -n LDS_ER -t ROC

CODA 2.5,Name : LDS_ER, Type ER Id : 0

sh: cmlog_activate: command not found

"LDS_ER" state now "booted"

daLogMsg: "LDS_ER" state now "booted"

DAQ::LDS_ER>

runcontrol

~ >source CODA/setup

~ >runcontrol

sh: uncompress: command not found

Runcotrol User interface

Connect

Configure

SIS3610

Download

Then, dead

Dr. Forest fixed with restarted daq machine

4th Trial

Error art telnet roc1

~ >telnet roc1

Trying 10.1.1.2...

telnet: connect to address 10.1.1.2: No route to host

Firewall of daq is on. If Firewall is on, ROC won't be able to read data from daq. Need to turn it off after log in as super user:

~ >su

Password:

[root@daq1 daq]# /sbin/service iptables stop

Flushing firewall rules: [ OK ]

Setting chains to policy ACCEPT: filter [ OK ]

Unloading iptables modules: [ OK ]

[root@daq1 daq]#

5th Trial

After running runcontrol, runcontrol is dead

Download configuration to ROC

Click COnfigure in the Runcontrol GUI
select V775_TDC from the pull down menu
click the download button in the runcontrol GUI

 You should see message appears on several of the open windows.  
You should see information in the ROC window.  If you see error 
messages check that you loaded the libraries with the commands

-> ld <v792Lib.o
-> ld < v775Lib.o

Data Analysis with ROOTSYS

1st trial

Creating Histogram

~/data >~/CODA/CODAreader/UsingROOTnEVIO/Oleksiy/evio2nt -fr2581.dat > /dev/null

home/daq/CODA/CODAreader/UsingROOTnEVIO/Oleksiy/evio2nt: error while loading shared libraries: libet.so: cannot open shared object file: No such file or directory

Changing Name

~/data >mv r2581 r2581.root

Starting ROOTSYS

~/data >root r2581.root

I forgot source CODA

2nd Trial - Successful trial

source ~/CODA/setup

Monitoring data old way

~/CODA/CODAreader/UsingROOTnEVIO/Oleksiy/evio2nt -fr2581.dat > /dev/null

mv r2581 r2581.root

root r2581.root

Create histogram for data to see it in finer binning:

TH1F *Hist1=new TH1F("Hist1","Hist1",4600,0.5,4600.5)

ntuple->Draw("ADC2 >> Hist1")

Monitoring data on line

~/CODA/CODAreader/UsingROOTnEVIO/Oleksiy/Monitor/hsimple -dev 1 -chan 1

Detector Test

Det1

Co60 test 1

Co60 activity: 954.1 nCi

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2614	Co60	19 s	1015	1 / ADC2
2615	Co60	23 s	1050	1 / ADC2
2616	Co60	40 s	1100	1 / ADC2
2617	Co60	2 min 30 s	1090	1 / ADC2
2618	Co60	2 min 27 s	1090	0 / ADC1
2619	Co60	1 min 35 s	1090	31 / ADC32	Empty
2620	Co60	3 min 29 s	1090	2 / ADC3

Channel 0 appears to be noisy compared to channel 1 and 2.  Perhaps Channel 31 has a software problem?

Na22 test 1

Na22 activity: 1196 nCi

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2621	Na22	6 min 17 s	1090	2 / ADC3

Cosmic test 1

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2622	Cosmic	2 h 13 min 4 s	1090	2 / ADC3

Det2

Co60 test 2

Co60 activity: 954.1 nCi

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2623	Co60	2 min 25 s	902	2 / ADC3
2624	Co60	2 min 22 s	1000	2 / ADC3
2625	Co60	2 min 4 s	1100	2 / ADC3
2626	Co60	2 min 8 s	1080	2 / ADC3

Na22 test 2

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2627	Na22	1 min 39 s	1080	2 / ADC3

Cosmic test 2

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2628	Cosmic	2 h 4 min 14 s	1080	2 / ADC3

Pulse generator test

Haithum was using pulser. I saw pulses from the pulser on the scope. I want to study its effect on the spectrum.

Run #	pulser	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2629	off	Na22	2 min 33 s	1080	2 / ADC3
2630		Na22	h min s	1080	2 / ADC3	200 px 200 px

Det1

Co60 test 3

Co60 activity: 954.1 nCi

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2634	Co60	2 min 37 s	1080	2 / ADC3
2635	Co60	4 min 42 s	1070	2 / ADC3
2636	Co60	2 min 44 s	1060	2 / ADC3

Na22 test 3

Na22 activity:

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2637	Na22	3 min 10 s	1060	2 / ADC3
2638	Na22	3 min 32 s	1070	2 / ADC3

Det 4

Co60 test 4

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2639	Co60	3 min 4 s	1070	2 / ADC3
2640	Co60	5 min 18 s	1060	2 / ADC3

Na22 test 4

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2641	Na22	3 min 18 s	1060	2 / ADC3
2642	Na22	3 min 1 s	1070	2 / ADC3

Cosmic test 4

Run #	Source	Run Duration (s)	HV (V)	ADC Channel (V792/root)	Spectrum
2643	Cosmic	3 h 55 min 5 s	1070	2 / ADC3
2644	Cosmic	8 h 27 min 53 s	1060	2 / ADC3

ROC1 crashed and run 2644 stopped. I lost information when it was started and ended. I checked the property of the r2644.dat file by right clicking on it. It says

Modified: Mon 21 Nov 2011 05:07:48 AM MST

Accessed: Sun 20 Nov 2011 08:39:55 PM MST

More tests

Pulse Shapes

Det3

Cosmics	Na22	Co60

Put the Na22 and Co60 peaks together

Charge of single pulse of 511 peak

1) Confirm ADC charge calibration by using a battery. Integrate gate with around 50 ns.

2) Play with gate width and HV, see how the charge changes, as we as how the 511 keV peaks shifts.

3) Charge vs ADC_Channel number, should be linear. y intercept is noise.

4) HV vs Charge for 511 keV for each NaI detectors.

Confirming ADC Charge Calibration

Voltage of battery: V = 1.556 V

Changing Pulse widths

Charge changing as pulse width changes

T F:You are just measuring noise if the signal size has a mean of less than 100 channels.

S S:Looks like the channel 16 is not good. I also changed the polarity. It worked. 
    But the change is not linear with the pulse width.

Run #	Source	Battery Voltage (V)	Events (on CODA)	Pulse Width (ns)	ADC Channel (V792/root)	Spectrum
2645	Hand Trigger with battery	1.556	218	about 50	15 / ADC16
2646	Hand Trigger with battery	1.556	214	about 165	15 / ADC16

    Changed from channel 16 to channel 3. Polarity also changed.

Voltage: U = -1.556 V.

There is a resistor connected to the battery with resistance of R = 996 [math]\Omega[/math]

Impedance: R = 50 [math]\Omega[/math]

Current:

Charge:

Gain: 100fC/channel

If I have peak at 800th channel, then my charge 800*100 fC=800*0.1 pC = 800/1000 *0.1 nC.

If I have peak at Nth channel, then my charge N*100 fC= N*0.1 pC = N/10000 nC.

Run #	Source	Battery Voltage (V)	Events (on CODA)	Pulse Width (ns)	Charge (nC)	ADC Channel (V792/root)	Spectrum	Charge from ADC Reading (nC)
2652	Hand Trigger with battery	-1.556 (Polarity Changed)	59	about 1000	1.4875717	2 / ADC3		over flow
2653	Hand Trigger with battery	-1.556 (Polarity Changed)	61	about 500	0.743785851	2 / ADC3		0.387
2654	Hand Trigger with battery	-1.556 (Polarity Changed)	62	about 75	0.111567878	2 / ADC3		0.086
2655	Hand Trigger with battery	-1.556 (Polarity Changed)	52	about 200	0.29751434	2 / ADC3
2656	Hand Trigger with battery	-1.556 (Polarity Changed)	56	about 300		2 / ADC3
2657	Hand Trigger with battery	-1.556 (Polarity Changed)	54	about 350		2 / ADC3
2658	Hand Trigger with battery	-1.556 (Polarity Changed)	63	about 300		2 / ADC3
2659	Hand Trigger with battery	-1.556 (Polarity Changed)	63	about 250		2 / ADC3
2660	Hand Trigger with battery	-1.556 (Polarity Changed)	60	about 200		2 / ADC3
2661	Hand Trigger with battery	-1.556 (Polarity Changed)	57	about 150		2 / ADC3
2662	Hand Trigger with battery	-1.556 (Polarity Changed)	62	about 100		2 / ADC3
2663	Hand Trigger with battery	-1.556 (Polarity Changed)	56	about 50		2 / ADC3

                       Charge on 
                       time            Time Window     Charge from
       Run #           Calculation     Width           Channel Counts  Channel 	Gain

Q (nC) Delta T (nS) Q (nC) Number (0.1 nC/Chan)

       2654		0.11157		75		0.08600		860		0.00010
       2655		0.29751		200		0.21450		2145		0.00010
       2656		0.44627		300		0.31980		3198		0.00010
       2657		0.52065		350		0.37050		3705		0.00010
       2658		0.44627		300		0.32000		3200		0.00010
       2659		0.37189		250		0.26750		2675		0.00010
       2660		0.29751		200		0.21750		2175		0.00010
       2661		0.22314		150		0.16480		1648		0.00010
       2662		0.14876		100		0.11230		1123		0.00010
       2663		0.07438		50		0.06030		603		0.00010

Positrons

IAC NaI Detectors

General info on IAC NaI detector

Crystal size

PMT base configureation

IAC NAI_0

Detector and Parts

Big pulse due to scope 1 M ohm scope resistance

IAC NAI_1

IAC_NAI_2

Tests with 50 Ohm Scope Resistance

IAC NAI_1 with Base #1

IAC NAI_2 with Base #2

IAC NAI_3 with Base #3

IAC NAI_4 with Base #4

Calibration

Starting CODA

Starting

1st Terminal

2nd Terminal

3rd Terminal

4th Terminal

5th Terminal

6th Terminal

7th Terminal

1st Attempt - Failed

1.msqld

telnet roc1

et_start

rcServer

coda_eb

coda_er

runcontrol

Run Control Interface

1st Attempt

2nd Attempt

3rd Attempt

Second Attempt to Start CODA

msqld

telnet roc1

et_start

rcServer

coda_eb

coda_er

runcontrol

Run Control Interface

Third Attempt to Start CODA

msqld

telnet roc1

et_start

rcServer

coda_eb

coda_er

runcontrol

Runcotrol User interface

4th Trial

Error art telnet roc1

5th Trial

Download configuration to ROC

Data Analysis with ROOTSYS

1st trial

Creating Histogram

Changing Name

Starting ROOTSYS

2nd Trial - Successful trial

Monitoring data old way

Monitoring data on line

Detector Test

Det1

Co60 test 1

Na22 test 1

Cosmic test 1

Det2

Co60 test 2

Na22 test 2

Cosmic test 2

Pulse generator test

Det1

Co60 test 3

Na22 test 3

Det 4