Tune parameters

Previous Tune at the higher energy

Solenoid 1	5.4 A
Solenoid 2	5.5 A
Gun Ver	-0.2 A
Gun Hor	+0.4 A
Output Hor	-0.5 A
Output Ver	-0.5 A
Gun HV	+9.75 (Knob Setting)
Gun Grid Voltage	5.25 (Knob Setting)
RF frequency	2855.813 MHz
Modulator HV Power Supply	4.11 (Knob Setting)
RF macro Pulse Length (FWHM)	200 ns

Solenoid comparison with yesterdays higher energy tune

V1 (Gun Vertical)	H1 (Gun Horizontal)	Sol1 (Gun Sol)	V2 (Output Vertical)	H2 (Output horizontal	Sol 2 (Output solenoid)	OTR Pict	FC pict
(A)	(A)	(A)	(A)	(A)	(A)
(-0.3)	+0	0	0	-0	-0
(-0.2)	+0.4	5.4	-0.5	-0.5	5.5
(-0.2)	+0.4	6.8	-0.5	-0.5	5.5
(-0.2)	+0.4	6.8	-0.5	-0.5	10.4

Quad Scans

To test reproducibility from yesterday. Scan at 40, 20, 10, 5 mA peak currents. Scan twice on each Current.

Do Energy Scan

Bend the beam through 45 bending dipole, take images on the scope of FC and YAG images.

D1 current	Energy	FC peak Volt	Pic
(A)	MeV	mV
28	11.85	39
29	12.3	74
30	12.74	93
30.5	12.96	65
30.7	large uncertainty	22

Quad 1 Scan

Quad 1	OTR Pict	FC pict
(A)
+0
+0.2
+0.4
+0.6
+0.8
+1.0
+1.2
+1.4
+1.6
+1.8
+2.0

Scan Quad 4

Calibration

Estimate the error in the above calibration

image	OTR image	Calibration
		cal_h = 31.75 mm / 737 px = 0.04308 mm/px; cal_v = 31.75 mm / sqrt(2) / 531 px = 0.04228 mm/px;
		cal_h = 31.75 mm / 738 px = 0.04302 mm/px; cal_v = 31.75 mm / sqrt(2) / 535 px = 0.04196 mm/px;
		cal_h = 31.75 mm / 735 px = 0.04320 mm/px; cal_v = 31.75 mm / sqrt(2) / 532 px = 0.04220 mm/px;
		cal_h = 31.75 mm / 735 px = 0.04320 mm/px; cal_v = 31.75 mm / sqrt(2) / 536 px = 0.04189 mm/px;
		cal_h = 31.75 mm / 749 px = 0.04239 mm/px; cal_v = 31.75 mm / sqrt(2)) / 539 px = 0.04165 mm/px
		cal_h = 31.75 mm / 732 px = 0.04337 mm/px; cal_v = 31.75 mm / sqrt(2) / 536 px = 0.04189 mm/px
		cal_h = 31.75 mm / 735 px = 0.04320 mm/px; cal_v = 31.75 mm / sqrt(2)) / 532 px = 0.04220 mm/px

cal_h (mm/px)	cal_v (mm/px)
0.04308	0.04228
0.04302	0.04196
0.04320	0.04220
0.04320	0.04189
0.04239	0.04165
0.04337	0.04189
0.04320	0.04220
mean (mm/px)	mean (mm/px)
[math] 0.04307 \pm 0.00032 [/math]	[math] 0.04201 \pm 0.00023 [/math]

Data Analysis

Preliminary results

Here is the study on how to fit non_Gaussian curve. I fitted for whole image as well as parts of the image.

Here is beam profile, which is non-Gaussian.

Fits for whole image:

Fits for x=[362,404] and y=[241,301]:

Gaussian fitted for whole image

12.74 MeV

Fitted Gaussian for whole image x-projection:

Gaussian fitted for part 1 of the image

Fitted Gaussian for part 1 of the image

       xl = 362;% center at 382
       xr = 404;
       yl = 241;% center at 271
       yr = 301;

xl: x left, xr: x right. yl: y left, yr: y right.

x-projection:

Gaussian fitted for part 2 of the image

Fitted Gaussian for part 2 of the image

       xl = 342;% center at 382
       xr = 424;
       yl = 241;% center at 271
       yr = 301;

x-projection:

Gaussian fitted for part 3 of the image

Fitted Gaussian for part 3 of the image

       xl = 342;% center at 382
       xr = 424;
       yl = 221;% center at 271
       yr = 321;

x-projection:

Gaussian fitted for part 4 of the image

Fitted Gaussian for part 4 of the image

       xl = 322;% center at 382
       xr = 444;
       yl = 221;% center at 271
       yr = 321;

x-projection:

Analysis with root

Q1_Scan, 42mA peak current, Scan Coil Current at positive 1.8_Amp

Image

Back grounds

Signal	Background

These MATLAB fits are set to fit at 0.7 times above height of the peak.
Matlab fit to x profile	Matlab fit to y profile

sigma_x = 24.97 px	sigma_y = 44.45 px
Blue: Signal, Red Background, Black: Subtraction
signal
background
signal - background
signal
background
signal - background

The red line is the background above which seems to be larger than the signal. Why?

Below I zoom in on channel 250 where you can see that for this channel the background is larger. I then plot, on the right, all the elements along the x direction what are added up to get the values on the right.

Why isn't the addition making sense?

Q6_Scan, 42mA peak current, Scan Coil Current at negative 2.5_Amp

Signal	Background

Matlab fit to x profile	Matlab fit to y profile
set to fit at 0.2 times above height of the peak.	set to fit at 0.7 times above height of the peak.

sigma_x = 31.37 px	sigma_y = 18.63 px