Bipolar Transistor

The Bipolar transistor concept

From the last chapter we saw a p-n junction diode which had similar characteristic current-vs- voltage responses when biased either in the forward direction or backward.


The n-p junction. The depletion region is represented as the shaded square	The potential

The n-p junction. The depletion region is represented as the shaded square. Notice the depletion region (and E-field in that region) is larger than the forward biased n-p juntion	the potential

The n-p junction. The depletion region is represented as the shaded square. Notice the depletion region (and E-field in that region) is larger than the forward biased n-p juntion	the potential

The bottom p-n junction, when forward biased, provides a large current with a small voltage bias.

The top half of the p-n-p transistor is reversed biased, providing a "throttle" for the large current from the lower half.

The electric field points to the "collector" in the depletion region enlarged by the reverse bias. This moves the majority charge carriers away from the collector-base junction. Once outside the depletion zone, the charge carriers rely on diffusion to escape the material.

Bipolar transistor currents

Conservation of Current

Here it is the case that the positive current is actually representing the flow of positively charged holes (in non-semi-conductors the current represent the opposite direction of the flowing electrons)

You might think that the base current is larger than the collector current because of the reverse bias on the collector which leads to the base having lower resistance than the collector.

The above is not the case.

The potential [math]V_{BE}[/math] continuously draws electrons out of the emitter thus creating holes in the emitter. These holes diffuse into the base and are in a free-field region until they reach the depletion region between the collector and base.

While in the free-field region of the base they can do one of three things

diffuse to the depletion region where they see the electric field and get swept into the collector.
recombine with the mobile electrons in the base (the base is n-type material so electrons are the majority charge carriers)
re-combine with electrons injected by [math] V_{BE}[/math] into the base through the resistor [math]R_{BE}[/math]

Usually the last two processes are more likely.

BUT if you make the emitter thin enough (less than the mean free path of the holes) then you can have the first process dominate such that most of the holes get swept into the collector before they get a chance to recombine.

As a result a large fraction of the current into the emitter ([math]\alpha \sim -.99[/math]) goes into the collector. ([math]I_C = \alpha I_E[/math])

returning to conservation of current

So small changes in [math]I_B[/math] produce large changes in [math]I_C[/math] (You can control a large current[math] I_C[/math] using a small current [math]I_B[/math])

This is an amplifier!

If you inject a signal into the base then the small changes in the base current will result in large changes in the collector current.

Making a Transistor

As described above, the p-n-p junction is formed by "sandwiching" a thin n-type semicondor with 2 p-type semi-conductors.

The term "sandwiching" is in quotes because you DON'T glue 3 semiconductors together.

vertical diffuse planar transistor

Instead you start with a pure crystal of silicon that has been doped to to form the type os semi-conductor you wish to have as the COLLECTOR.

For now let's assume p-type, this means you dope pure silicon with boron. The collector is big (thick) because it has a lot of heat to dissipate.

Then you dope the crystal with impurities (Phosphorus) such that a thin n-type layer is formed, by diffusion, in the middle of the p-type crystal.

You then need to treat the top layer with dopant again to overcoming the n-type characteristics which are left over from forming the n-type base in the middle of the device AND create more holes with larger dopant than the collector. This step will directly influence the gain([math]\alpha[/math] and [math]\beta[/math]) of the transistor. The "+" label in the image below indicates that it is more p-type than the collector.

The critical feature of the process is to establish abrupt changes in the doping which create sharp boundaries.

You then coat the collector side with a conductor like metallic aluminum.

On the side used to transport dopant you need to construct contacts for the base and emitter. To do this you need an insulation layer and a conductor layer which passes through the insulation and makes contact with the base and emitter material. You use a stencil to deposit an insulating layer of SiO2 which will have holes that leave the base and emitter semiconductor material exposed. Then you deposit metallic aluminum conductor into the holes.

Epitaxial growth

The epitaxial method to create transistors is a layer-by-layer construction method in which the crystal is actually "grown" by depositing layers onto a subtrate.

There are three general methods of growing a crystal.

Vapor-phase Epitaxy: Most common way to grow silicon. A gas like silicon tetrachloride is mixed with hydrogen. The final state of the reaction has a pure silicon silicon wafer forming and a hydrogen chloride byproduct. If the hydrogen chloride is to dense you can get some etching. The growth rate ( 2 microns/min) is known and controllable, in some cases reversible. Dopants are added to the gas for the desired semiconductor type.
Liquid phase Epitaxy: the semiconductor ( pure or a mixture of two) is melted and grown onto a substrate by cooling at a rate of 0.1 to 1 micron/minute. Dopants are mixed into the liquid state semiconductor. Used mostly for making compound semiconductors.
Solid Phase Epitaxy: A substrate is deposited with material. The crystal is formed by heating the solid then ions are implanted onto the crystal. The method is mostly for healing crystal damage.
Molecular Beam Epitaxy: This uses a beam of particles (electrons) to heat material under vacuum such that the material evaporates and then condenses on a substrate above the crucible. Similar to Vapor-phase Epitaxy.

Bipolar Circuits

Ideal circuit

The above represent an ideal circuit in which the emitter terminal is shared between the input and output voltage. This is referred to as the "common emitter" configuration.

Holes are the majority carriers in the PNP Bipolar transistor. This becomes evident if you look at how the batteries are attached. Note: the "holes" flow only in the semiconductor itself and while electrons flow in the circuit external to the semi-conductor in response to how the holes are flowing in the semi-conductor.

The base-emitter junction configured to be a forward biased diode and the base-collector junction is reverse biased. So the base is more "negative" than the emitter and the collector is more "negative than the base.

The current flow ([math]I_B[/math]) is the result of electrons flowing into the base to combine with holes that are moving from the emitter to the base. Electrons exit the battery [math]V_{BE}[/math] and flow to the base to combine with holes and electrons exit the emitter toward the positive battery terminal creating holes in the emitter which diffuse into the base. The recombination that takes place in the base is small compared to what takes place in the collector due to the thin base thickness and the large electric field produces by the expanded depletion region caused by the reverse biasing of the collector.

I_B -vs- V_{BE} looks like a forward biased diode.

The current[math] I_C[/math] (and[math] I_B[/math]) are produced when holes move from the emitter to the collector and meet electrons which are supplied by the battery [math]V_{CE}[/math]. If you look at the relationship between [math]I_C[/math] and[math] V_{CE}[/math] you will see two regions.

The Active mode region represent the situation in which the p-n junction of the collector and base is reverse biased such that holes from the emitter can travel to the collector with little chance of recombining in the base. In this region, small changes in the base current result in large changes in the collector current while the potential difference between the collector and emitter is constant.

The Saturation region occurs at low[math] V_{CE}[/math] voltage and represents the situation just before reverse biasing turns on the flow (cut-in voltage), in essence both p-n junctions are forward biased so the collection current depends on the collector-emitter Voltage [math]V_{CE}[/math].

Testing for pnp or npn

You can use an Ohmmeter to tell if a transistor is pnp or npn.

Generally the base is the middle of the three pins for a bi-polar transistor.

If you put the voltmeters positive probe on the emitter lead and the ground probe onto the base lead, then a pnp transistor will yield a low resistance (1- 10 [math]\Omega[/math]s).

If it is a npn transistor then the positive probe on the base and the ground on the emitter will yield the small resistance.

So it you know which leads are emitter and base you can determine transistor type.

If you know transistor type, you can determine which lead is the emitter.

You can test if the transistor is good or not using the table below with the Ohmeter set on the 1[math] \Omega[/math] range.

type	[math]R_{BE}[/math]	[math]R_{EB}[/math]	[math]R_{BC}[/math]	[math]R_{CB}[/math]	[math]R_{CE}[/math]	[math]R_{EC}[/math]
pnp	high	low	high	low	high	high
npn	low	high	low	high	high	high

Bipolar Transistor Amplifier

Consider the above circuit.

Observations

1.) Notice the input goes through a high pass filter with a break point of[math] \frac{1}{R_1 C_1}[/math].

2.) The output also goes through a high pass filter with a break point of[math] \frac{1}{R_l C_2}[/math].

3.) Kirchoff voltage rule

Forest_Electronic_Instrumentation_and_Measurement

TF EIM Chapt5

Contents