Lab 10 RS
Lab 10 Unregulated power supply
Use a transformer for the experiment.
here is a description of the transformer.
File:TF EIM 241 transformer.pdf
Half-Wave Rectifier Circuit
1.)Consider building circuit below.
Determine the components needed in order to make the output ripple have a [math]\displaystyle{ \Delta V }[/math] less than 1 Volt.
The output ripple can be found by [math]\displaystyle{ \Delta V=\frac{I\Delta t}{C} }[/math]
Taking AC signal from outlet equals to [math]\displaystyle{ 60\ Hz }[/math] my input pulse width is [math]\displaystyle{ \Delta t = 17\ ms }[/math] and using say [math]\displaystyle{ C = 2.2\ uF }[/math] to make [math]\displaystyle{ \Delta\ V \ll 1\ V }[/math] I need my current to be:
[math]\displaystyle{ I \ll \frac{1\ V \cdot 2.2\ uF}{17\ mA} \ll 0.129\ mA }[/math]
The output ripple can be found by [math]\displaystyle{ \Delta V=\frac{I\Delta t}{C} }[/math]
I have used the following components and input parameters:
[math]\displaystyle{ R = 96.9\ k\Omega }[/math] [math]\displaystyle{ R_L = 98.7\ k\Omega }[/math] [math]\displaystyle{ R_{scope} = 1\ M\Omega }[/math] [math]\displaystyle{ C = 2.2\ uF }[/math]
and the following input parameters:
[math]\displaystyle{ \Delta t = 17\ ms\ which\ corresponds\ to\ 60\ Hz }[/math] [math]\displaystyle{ V_{in} = 12\ V }[/math]
The current through the circuit can be found as [math]\displaystyle{ I = \frac{V_{in}}{R_{tot}} }[/math]
where [math]\displaystyle{ R_{tot} = R + \left|\frac{R_L \cdot \frac{1}{j\omega C}}{R_L + \frac{1}{j\omega C}} \right| = R + \sqrt{ \left(\frac{R_L}{1 + j\omega CR_L}\right)\left(\frac{R_L}{1 + j\omega CR_L}\right)^* } = R + \sqrt{ \left(\frac{R_L^2}{1 + (\omega CR_L)^2}\right) } }[/math]
[math]\displaystyle{ = 96.9\ k\Omega + \sqrt{\frac{(98.7\ k\Omega)^2 }{1 + (2\pi\ 60\ sec^{-1})^2(2.2\ uF)^2 (98.7\ k\Omega)^2} }= 96.9\ k\Omega + 1.2\ k\Omega =98.1\ k\Omega }[/math].
And the current becomes [math]\displaystyle{ I = \frac{12\ V}{98.1\ k\Omega} = 0.122\ mA }[/math]
So my output ripple becomes [math]\displaystyle{ \Delta V = \frac{0.122\ mA \cdot 17\ ms}{2.2\ uF} = 0.9 V }[/math]
List the components below and show your instructor the output observed on the scope and sketch it below.
Full-Wave Rectifier Circuit
Determine the components needed in order to make the above circuit's output ripple have a [math]\displaystyle{ \Delta V }[/math] less than 0.5 Volt.
List the components below and show your instructor the output observed on the scope and sketch it below.
Go Back to All Lab Reports Forest_Electronic_Instrumentation_and_Measurement