CH He3 Attenuation Measurements Revisited

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

He3 Tube Plateau

Measurements

1250V Source Out Data
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)
1	Detector on 3D printed stands at +1250V	125	No		100
2	Detector on 3D printed stands at +1250V	145	No		100
3	Detector on 3D printed stands at +1250V	155	No		100
4	Detector on 3D printed stands at +1250V	160	No		100
5	Detector on 3D printed stands at +1250V	165	No		100
6	Detector on 3D printed stands at +1250V	170	No		100
7	Detector on 3D printed stands at +1250V	175	No		100
8	Detector on 3D printed stands at +1250V	185	No		100
9	Detector on 3D printed stands at +1250V	205	No		100
10	Detector on 3D printed stands at +1250V	225	No		100
11	Detector on 3D printed stands at +1250V	245	No		100
12	Detector on 3D printed stands at +1250V	255	No		100

1250V Source In Data
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)
1	Detector on 3D printed stands at +1250V	125	Yes		100
2	Detector on 3D printed stands at +1250V	145	Yes		100
3	Detector on 3D printed stands at +1250V	155	Yes		100
4	Detector on 3D printed stands at +1250V	160	Yes		100
5	Detector on 3D printed stands at +1250V	165	Yes		100
6	Detector on 3D printed stands at +1250V	170	Yes		100
7	Detector on 3D printed stands at +1250V	175	Yes		100
8	Detector on 3D printed stands at +1250V	185	Yes		100
9	Detector on 3D printed stands at +1250V	205	Yes		100
10	Detector on 3D printed stands at +1250V	225	Yes		100
11	Detector on 3D printed stands at +1250V	245	Yes		100
12	Detector on 3D printed stands at +1250V	255	Yes		100

Plateau Plots
Plateau measurements at 700V, source in and source out overlaid.	Plateau measurements at 700V, source in minus source out.	Signal to Noise ratio for 700V at different discriminator voltages

Repeat of Initial Experimental Setup

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

Measurements

1" Green poly

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

2" Green poly (one brick) no thermalizer

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

3" Green poly (one brick & sheet)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

4" Green poly (two bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

6" Green poly (three bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

8" Green poly (four bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

Attenuation Experiment using HPGe Lynx System as PSU/DAQ

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

Attenuation Experiment using New Modules in Electronics Chain

Experimental Setup

Polyethylene Structure

This section to include type of poly, location, source-detector distance, images, etc

Detector

Include images, model/serial number of detector, physical parameters, etc

Electronics Chain

Include schematic of electronics chain

Components

Each component of electronics chain with make/model, function, and brief description of why it's present

Lecroy Discriminator Model 821

• 255mV threshold

• Pulse width as measured on scope: 20ns

Ortec Spec Amp Model 672

• 10x Course Gain

• 1x Fine Gain

• 2us Shaping Time

• Uni Shaping: Gaussian

• Input: Norm (-)

• Output: Unipolar

Dual Timer

• Discriminator output used to start timer

• Timer output used to trigger scalar

• Pulse width as measured on scope: 100ns

Scope Images

• 

  Purple: CAEN Dual Timer using Lecroy Disc as input. 100ns pulse width. Aqua: Lecroy Disc Output. 20ns pulse width.

Background Measurements

1250V Background Measurements
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on poly at +1250V	255	No	63	100
2	Detector on poly at +1250V	255	No	52	100
3	Detector on poly at +1250V	255	No	65	100
4	Detector on poly at +1250V	255	No	53	100
5	Detector on poly at +1250V	255	No	70	100

Measurements

0" Green Poly

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes	5835	100
2	Detector on 3D printed stands at +1250V	255	Yes	5730	100
3	Detector on 3D printed stands at +1250V	255	Yes	5801	100
4	Detector on 3D printed stands at +1250V	255	Yes	5913	100
5	Detector on 3D printed stands at +1250V	255	Yes	5837	100

1" Green poly

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

2" Green poly (one brick)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

3" Green poly (one brick & sheet)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

4" Green poly (two bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

6" Green poly (three bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

8" Green poly (four bricks)

1250V source in
Run Number	Configuration	Discriminator Threshold (mV)	Cf-252 Source	Counts	Run Time (Sec)	Count Rate (Hz)	Uncertainty
1	Detector on 3D printed stands at +1250V	255	Yes		100
2	Detector on 3D printed stands at +1250V	255	Yes		100
3	Detector on 3D printed stands at +1250V	255	Yes		100
4	Detector on 3D printed stands at +1250V	255	Yes		100
5	Detector on 3D printed stands at +1250V	255	Yes		100

---

Previous Page

CaGaS Phase II