Difference between revisions of "Lab 4 RS"

From New IAC Wiki
Jump to navigation Jump to search
Line 27: Line 27:
 
4. Measure the input and output voltages for at least 8 different frequencies which span the frequency range from 1 Hz to 1 MHz.
 
4. Measure the input and output voltages for at least 8 different frequencies which span the frequency range from 1 Hz to 1 MHz.
  
{| border="3" cellpadding="20" cellspacing="0"
+
 
|<math>\nu</math> ||<math>V_{in}</math> || <math>V_{out}</math> || <math>\frac{V_{out}}{V_{in}}</math>
+
{| border="1" cellspacing="0" style="text-align: center; width: 500px; height: 500px;"
 +
|+ '''Table1. Voltage gain vs. frequency measurements'''
 
|-
 
|-
| Hz || Volts || Volts ||
+
! scope="col" width="50" | <math>\nu\ [\mbox{kHz}]</math>
 +
! scope="col" width="50" | <math>V_{in}\ [V]</math>
 +
! scope="col" width="50" | <math>V_{out}\ [V]</math>
 +
! scope="col" width="50" | <math>\frac{V_{out}}{V_{in}}</math>
 
|-
 
|-
| || || ||
+
|0.1 || || ||
 
|-
 
|-
| || || ||
+
|1.0 || || ||
 
|-
 
|-
| || || ||
+
|2.0 || || ||
 
|-
 
|-
| || || ||
+
|3.0 || || ||
 
|-
 
|-
| || || ||
+
|4.0 || || ||
 
|-
 
|-
| || || ||
+
|5.0 || || ||
 
|-
 
|-
| || || ||
+
|6.0 || || ||
 
|-
 
|-
| || || ||
+
|7.0 || || ||
 
|-
 
|-
| || || ||
+
|8.0 || || ||
 
|-
 
|-
| || || ||
+
|9.0 || || ||
 
|-
 
|-
| || || ||
+
|10.0 || || ||
 
|-
 
|-
| || || ||
+
|11.0 || || ||
 
|-
 
|-
 +
|12.0 || || ||
 +
|-
 +
|15.0 || || ||
 +
|-
 +
|20.0 || || ||
 +
|-
 +
|30.0 || || ||
 +
|-
 +
|40.0 || || ||
 +
|-
 +
|50.0 || || ||
 +
|-
 +
|100.0 || || ||
 +
|-
 +
|200.0 || || ||
 
|}
 
|}
  

Revision as of 05:27, 26 January 2011

Go Back to All Lab Reports


RC High-pass filter

1-50 kHz filter (20 pnts)

1. Design a high-pass RC filter with a break point between 1-50 kHz. The break point is the frequency at which the filter's attenuation of the AC signal goes to 0(not passed). For a High pass filter, AC signals with a frequency below the 1-50 kHz range will be attenuated .

TF EIM Lab4.png


To design low-pass RC filter I had:
[math]R=10.5\ \Omega[/math]  
[math]C=1.250\ \mu F[/math]

So

[math]\omega_b = \frac{1}{RC} = 76.19\cdot 10^3\ \frac{rad}{s}[/math]
[math]f_b = \frac{\omega_b}{2\pi} = 12.13\ \mbox{kHz}[/math]


2. Now construct the circuit using a non-polar capacitor.

3. Use a sinusoidal variable frequency oscillator to provide an input voltage to your filter.

4. Measure the input and output voltages for at least 8 different frequencies which span the frequency range from 1 Hz to 1 MHz.


Table1. Voltage gain vs. frequency measurements
[math]\nu\ [\mbox{kHz}][/math] [math]V_{in}\ [V][/math] [math]V_{out}\ [V][/math] [math]\frac{V_{out}}{V_{in}}[/math]
0.1
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
15.0
20.0
30.0
40.0
50.0
100.0
200.0

5. Graph the [math]\log \left(\frac{V_{out}}{V_{in}} \right)[/math] -vs- [math]\log (\nu)[/math]

phase shift (10 pnts)

  1. measure the phase shift between [math]V_{in}[/math] and [math]V_{out}[/math]

Questions

  1. compare the theoretical and experimentally measured break frequencies. (5 pnts)
  2. Calculate and expression for [math]\frac{V_{out}}{ V_{in}}[/math] as a function of [math]\nu[/math], [math]R[/math], and [math]C[/math].(5 pnts)
  3. Compare the theoretical and experimental value for the phase shift [math]\theta[/math]. (5 pnts)
  4. Sketch the phasor diagram for [math]V_{in}[/math],[math] V_{out}[/math], [math]V_{R}[/math], and [math]V_{C}[/math]. Put the current [math]I[/math] along the real voltage axis. (30 pnts)
  5. what is the phase shift [math]\theta[/math] for a DC input and a very-high frequency input?(5 pnts)
  6. calculate and expression for the phase shift [math]\theta[/math] as a function of [math]\nu[/math], [math]R[/math], [math]C[/math] and graph [math]\theta[/math] -vs [math]\nu[/math]. (20 pnts)


Forest_Electronic_Instrumentation_and_Measurement Go Back to All Lab Reports