Readout Electronics

I/O

Inputs to breakout box

Trigger (LVDS)

Clock ( RF synced pulse 31 MHz = 499/16 MHz, LVDS)

Flip Flop scaner (1 TTL pulse)

V1495 :

28 Pin output on 34 pin ribbon cables

Inputs to V1495:

180 bits of data = 12 bits Bunch Counter ( =31 MHz clock) + 12 bit (Event Counter + flags) + 12 bits (Chip ID) + 128 bits (data) + 16 bits (Checksum)

The input register has been set to a size of 256 bit and there are 12 of them

[math]\Rightarrow \frac{0.5 kbytes}{s}[/math]

Timing

VFAT:

Progammable through the Latency register (8 bits = 256 bits) you have but only 128 registers data registers. We can go back in time 100 *32 ns = 3 micro seconds. But we only may need 100 ns.

V1495: can have programmable delay up to?

We can program delays and play with the timing by downloading values for "lat" into the VFAT extended register and set delay on the V1495 through the ROC.

The V1495 can also interupt the VME backplane telling a ROC to readout the planes.

FPGA to VME data transfer

On 2/15/07 Ben Royd tested the read and write speeds between the VPM backplane and the FPGA user registers. He was able to write 16 bits to USER FPGA in 330 ns.

[math]\Rightarrow \frac{16 bits}{330 ns}\times \frac{1 byte}{8 bits} \times \frac{10^9 s}{ns} \approx 6\frac{Mbytes}{s}[/math]

VFAT controls

Brian Oborn: 282- 6243

VFAT control registers

Control register 0

bit	bit name	Function
0	Sleep/Run	0 = sleep, 1=run also reffereed to as sleep blocking

Control Register 1

Control register 2

VFAT Clock and Trig pulses

MCLK and Trig LVDS pulses

The Clock and Trigger LVDS pusles for the VFAT board were generated using the SIS3610 I/O register. I simply wrote bits to the register. The I/O registers internal clock then determine the pulse frequency. I set the bits to be 1110000000000000 using the command

s3610VFATclock(0,57344);

and reset all bits to zero except for the trigger input (100000000000000 b = 16384 d )which remained high for the first 3 clock pulses by hardwiring the value 16384 in the SIS3610 library function call. According to Table 2 in the VFAT manual from July 2006, leaving the first 3 bits high tells the VFAT board to operate in "CalPulse" mode..

void s3610VFATclock(int id, unsigned int val)
{

 int i;

 if((id<0) || (s3610p[id] == NULL)) {
   logMsg("s3610WriteOutput: ERROR : SIS3610 id %d not initialized \n",id,0,0,0,0,0);
   return;
 }

 s3610p[id]->d_out = val;
 s3610p[id]->d_out = 16384;
 s3610p[id]->d_out = val;
 s3610p[id]->d_out = 16384;
 s3610p[id]->d_out = val;
 s3610p[id]->d_out = 16384;

 for(i=0;i<200;i++)
   {
     s3610p[id]->d_out = val;
     s3610p[id]->d_out = 0;
   }

 logMsg("s3610VFATclock: Finish pulses \n",id,0,0,0,0,0);
 return;

}

The third highest bit was used to drive the scope.

Cal pulse Procedure

Check that VCAL connects to DACo

1.) First set up the following values for operating the chip

Register	Value
IPreampIn
IPreampFeed
IPreampOut
IShaper
IShaperFeed
IComp

1.) Connect VCal to DACo-V by setting DACsel = 1001

echo "p 65 0 on p 65 1 off p 65 2 off p 65 3 on" | flipbit.arm

2.) set calibration mode to output VCal values by setting CalMode = 01

echo "p 64 6 on p 64 7 off p " | flipbit.arm

3.) set VCAL

this turns one of the 8 bits to the calibration voltage Vcal (It ranges from 1.074 to 0.877 Volts)

echo "e 129 1 on" | flipbit.arm

4.) Look for a voltage on the output connector pin #162.

Setting Thresholds

The registers VThreshold1 and VThreshold2 are used to set the threshold on the analog input. The actual threshold applied is given by the difference (VTheshold2 -Vthreshold1) in order to have the ability to set positive and negative thresholds. A negative threshold (for the GEM output signal) can be set by having VThreshold2 =0 and VThreshold1>0.

Using VCAL to test output digitization

You can use VCal to inject a pulse into the channels via the CalChan1 bit on each channel. You need to be sure CalPolarity is consistent with (VTheshold2-VThreshold1).

For channel 1 set TrimDAC= 1000 ( TrimDAC(4) =1 all others zero)

echo "e 1 1 off e 1 2 off e 1 3 off e 1 4 on" | flipbit.arm 

set everything off

echo "e 1 1 off e 1 2 off e 1 3 off e 1 4 off" | flipbit.arm 

for channel 128

echo "e 128 4 on" | flipbit.arm 

We may need to change the TrimDAC range

echo "e 134 0 on e 134 1 off e 134 2 on" | flipbit.arm

5.) send MClock pulses to look at output by using the SIS3610 to output a stream of LVDS pulses to the VFAT and look at DataOut

s3610VFATclock(0,57344);