Difference between revisions of "Mlr Summ TF"
Jump to navigation
Jump to search
Line 31: | Line 31: | ||
Weight the E-vs-Theta plot with Xsect | Weight the E-vs-Theta plot with Xsect | ||
− | [[File:MollerEThetaSigma_Full | + | [[File:MollerEThetaSigma_Full.png|frame|center|alt=Moller Electron Energy vs Angle Theta in Lab Frame|'''Figure 2:''' Using the theoretical differential cross section, the distribution of Moller electrons for a CM energy of approximately 53Mev can be distributed through the CM scattering angle Theta. Using Lorentz transformations, these distributions can be transformed to the lab frame. At around 60 degrees in the lab the Moller electron has an energy of close to 1 MeV. Such a low energy does not allow the Moller electron to leave the constrains of the target where they are created.]] |
== Baseline== | == Baseline== |
Revision as of 19:42, 30 August 2018
VanWasshenova_Thesis#Mlr_Summ_TF
Moller Summary
Scattering Xsect
https://wiki.iac.isu.edu/index.php/Converting_to_barns
![Theory Frame Moller CM Frame](/./images/thumb/3/3d/MolThetaCM_Theory.png/500px-MolThetaCM_Theory.png)
Figure 3a: A plot of the number of Moller scattering angle theta in the center of mass frame versus the theoretical differential cross section. The width of the bins is 0.001 degrees for the angles in the center of mass frame corresponding to angles of 5 to 40 degrees in the lab frame. A weight has been assigned for each value in theta which will give the theoretical differential cross section when applied.
![Theory Lab Frame Moller Frame](/./images/thumb/3/39/MolThetaLab_Theory.png/500px-MolThetaLab_Theory.png)
Figure 3b: A plot of the number of Moller scattering angle theta in the lab frame versus the theoretical differential cross section. The width of the bins is 0.5 degrees for the angles in the lab frame. A weight has been assigned for each value in theta which will give the theoretical differential cross section when applied.
![Lower Angle Theta Moller Electron Scattering in DC](/./images/thumb/1/1e/TotalS1R1HitsRate_LowerMoller_DCMagnets.png/500px-TotalS1R1HitsRate_LowerMoller_DCMagnets.png)
Figure 4a: A plot of the number of Moller scattering angle theta in the lab frame versus the scattering angle phi. The width of the Theta bins is 0.1 degrees in the lab frame within the range of 0 to 6 degrees. Similarly, the width of the Phi bins in 0.2 degrees in the lab frame within the range of -30 to 30 degrees. Only electrons that would have fallen within the range allowed by the DC endplates have been included. Only the DC is simulated with endplates of Tungsten steel.
![Theory Lab Frame Moller Frame](/./images/thumb/4/4c/Clas12_woTarg_LowerMoller.png/500px-Clas12_woTarg_LowerMoller.png)
Figure 3b: A plot of the number of Moller scattering angle theta in the lab frame versus the scattering angle phi. The width of the Theta bins is 0.1 degrees in the lab frame within the range of 0 to 6 degrees. Similarly, the width of the Phi bins in 0.2 degrees in the lab frame within the range of -30 to 30 degrees. Only electrons that would have fallen within the range allowed by the DC endplates have been included. The clas12 setup is simulated without a target.
Weight the E-vs-Theta plot with Xsect
![Moller Electron Energy vs Angle Theta in Lab Frame](/./images/b/be/MollerEThetaSigma_Full.png)
Figure 2: Using the theoretical differential cross section, the distribution of Moller electrons for a CM energy of approximately 53Mev can be distributed through the CM scattering angle Theta. Using Lorentz transformations, these distributions can be transformed to the lab frame. At around 60 degrees in the lab the Moller electron has an energy of close to 1 MeV. Such a low energy does not allow the Moller electron to leave the constrains of the target where they are created.
Baseline
Moller events using an lH2 target geometry No Raster
DC hits -vs- Solenoid
With the Torus at zero Magnetic field the solenoid is changes to show how moller electrons move off the faces of R1 DC.
With Magnet Components
Without Magnet Components
With Only S1R1 DC
What are the particles in the R1S1 only plot and where are they from
Moller Electron Events(1st hits)
Photons Hits in R1
Tomography
Moller events using an dual polarized target geometry with Raster
Photon Hits in R1 when Raster size has radius of 0.2 cm
Moller rate -vs- length of a single taerget
0.5 cm radius -vs- Z
Target is a one 0.5 cm radius cylinder of length Z.
By how much does the moller rate change at full field ?