Difference between revisions of "LB RunGroupC Vertex"
Line 291: | Line 291: | ||
|| GenPart.x || GenPart.y || GenPart.z || Event.x || Event.y || Event.z | || GenPart.x || GenPart.y || GenPart.z || Event.x || Event.y || Event.z | ||
|- | |- | ||
− | || | + | || || || || || || |
|- | |- | ||
|}<br> | |}<br> |
Revision as of 19:06, 8 August 2016
Vertex Reconstruction studies
Inclusive electron GEMC 2.4 & Coatjava 2.4
Summary
Set all histogram ranges to -6,6 cm and bin sizes of 0.1 cm
Point target X,Y,Z=0 cm
No Rastering | |
---|---|
Vx Difference | |
Vy Difference | |
Vz Difference | |
X Resolution (cm) | 0.2362 +/- 0.0008 |
Y Resolution(cm) | 0.09809 +/- 0.00033 |
Z Resolution (cm) | 0.05435 +/- 0.00017 |
These histograms raise some questions. To begin I created a LUND file with 6 GeV incident electrons at 25 degrees in theta and 0 degrees in phi. All of the vertex positions were set to 0. I then ran GEMC 2.4 using the command line ~/src/CLAS/GEMC/source/gemc -USE_GUI=0 -INPUT_GEN_FILE="LUND,No_Raster.LUND" -N=75000 eg12_sol_No_Raster.gcard
which created an output file called eg12_sol_75k_No_Raster.ev. After that the reconstruction command line used was
~/src/CLAS/coatjava-2.4/bin/clas12-reconstruction -i eg12_sol_75k_No_Raster.ev-config GEOM::new=true -config MAG::torus=-1.0 -config MAG::solenoid=1.0 -o eg12_sol_75k_No_Raster_rec.evio -s DCHB:DCTB:EC:FTOF:EB -config DATA::mc=true -config DCTB::useRaster=true
After the reconstruction a root file was created using
~/src/CLAS/evio2root/bin/evio2root eg12_sol_75k_No_Raster_rec.evio eg12_sol_75k_No_Raster_rec.root 75000
A plot was then created to show the X Vertex and Y Vertex Differences
The first question is why is there a shift in the Y Difference. What would make X more centered around 0? The next question is when rastering begins, why do the resolutions in the X Vertices remain unchanged while the resolutions in the Y Vertices change?
Point in 2-D but extended target in 1-D
Two vertex variables are fixed at zero and the third vertex variable is altered
Extended target -3 < Z < 3 cm
Extended target in Z. Vy shift analysis
All Histograms below were created by simply making the target longer along the Z axis. Each case uses vertex points for X and Y ranging from -1cm to 1cm
It would seem that increasing the length of the target in the Z direction has an effect on the resolution of the Y vertex position along with how far the center of the Gaussian peak will shift for the Y vertex differences.
Localized Vertex Resolution Investigation of Line Targets
GEMC was ran to create electrons being produced in a line along certain axes. These include three separate 2cm targets centered at (0,0,0) in the X, Y , and Z directions. The final target is a line along the Z axis centered at (0,0,0) that is 6cm long. The generated electrons were shot at 25 degrees in theta and 0 degrees in phi at an energy of 6GeV.
Here is an example of how the cuts were made. Consider the case of a 2cm line target in the Z direction centered at (0,0,0). Closed intervals begin at the end of the target and are 0.1cm long. So the first interval would be [-1.0,-0.9], then the next would be [-0.9, -0.8] and so on until the entire target is covered. The events in the EVENTHB bank were cut so that in any given interval there would be a margin of +/- 1cm to remove any outliers that may cause the histograms to have long tails.
Below are the histograms for the 2cm line target in Y,X=0,Z=0. The electrons were fired with an energy of 6 GeV at 25 degrees in theta at 0 degrees in phi.
GenPart.x | GenPart.y | GenPart.z | Event.x | Event.y | Event.z |
Below are the histograms for a 2cm target along the Y axis, X = 0 Z = 0. The electrons were fired with an energy of 6 GeV at 25 degrees in theta and 180 degrees in phi.
GenPart.x | GenPart.y | GenPart.z | Event.x | Event.y | Event.z |
Below are the Histograms for a 2cm long target in the X Direction with a 6GeV electron fired at 25 degrees in theta and 90 degrees in phi
GenPart.x | GenPart.y | GenPart.z | Event.x | Event.y | Event.z |
Below are the Vx Differences using a 2cm target in X with incident 6 GeV electrons at 25 degrees in theta and 270 degrees in phi
GenPart.x | GenPart.y | GenPart.z | Event.x | Event.y | Event.z |
Below are the histograms for a 6cm target in the Z direction using a 6 GeV electron fired at 25 degrees in theta and 90 degrees in phi.
GenPart.x | GenPart.y | GenPart.z | Event.x | Event.y | Event.z |
Interval | Resolution (cm) | Vx Difference | *** | Interval | Resolution (cm) | Vx Difference |
[-3.0,-2.5] | *** | [2.5,3.0] | ||||
[-2.5,-2.0] | *** | [2.0,2.5] | ||||
[-2.0,-1.5] | *** | [1.5,2.0] | ||||
[-1.5,-1.0] | *** | [1.0,1.5] | ||||
[-1.0,-0.5] | *** | [0.5,1.0] | ||||
[-0.5,0.0] | *** | [0.0,0.5] |
Elastic electron proton GEMC 2.4 & Coatjava 2.4
References
https://clasweb.jlab.org/wiki/index.php/TF_EG12_Vertex#Z_resolution_With_micro-megas