Lab 14 RS

Go Back to All Lab Reports

The Common Emitter Amplifier

Circuit

Construct the common emitter amplifier circuit below according to your type of emitter.

Calculate all the R and C values to use in the circuit such that

a. Try [math]R_B \approx 220 \Omega[/math] and [math]I_C \approx 100 \mu A[/math]

b. [math]I_C \gt 0.5[/math] mA DC with no input signal

c. [math]V_{CE} \approx V_{CC}/2 \gt 2[/math] V

d. [math]V_{CC} \lt V_{CE}(max)[/math] to prevent burnout

e. [math]V_{BE} \approx 0.6 V[/math]

f. [math]I_D \approx 10 I_B \lt 1[/math] mA

Let's [math]V_{CC} = 20\ V[/math], [math]R_E = 200 \Omega[/math] and [math]R_C = 1.8\ k\Omega[/math]. The load line equation becomes:

[math]I_C = \frac{V_{CC}}{R_E+R_C} + \frac{V_{EC}}{R_E+R_C} = \frac{20\ V}{2\ k\Omega} + \frac{V_{CE}}{2\ k\Omega} = (10 + 0.5 \cdot V_{CE})\ mA[/math]

This load line pretty high and give me the wide range of amplification the input signal.

Draw a load line using the [math]I_{C}[/math] -vs- [math]I_{EC}[/math] from the previous lab 13. Record the value of [math]h_{FE}[/math] or [math]\beta[/math].

On the plot above I overlay me output lines from the previous lab report #13 and me load line I am going to use to construct amplifier. My [math]\beta \approx 150[/math] based on my previous lab report #13

Set a DC operating point [math]I^{\prime}_C[/math] so it will amplify the input pulse given to you. Some of you will have sinusoidal pulses others will have positive or negative only pulses.

I will set up my operating point in the middle of the load line: [math]I_C = 5\ mA[/math], [math]V_EC = 10\ mA[/math]. So I will have the wide range of amplification the input signal [math]I_B = \pm 5\ mA[/math]

Let's calculate all bias voltage to set up this operating point.

[math]V_{EC} = I_E \cdot R_E = 5\ mA \cdot 0.2\ k\Omega = 1\ V[/math]
[math]V_{BE} = 0.6\ V[/math]
[math]V_{B} = V_{CE} + V_B = (1.0 + 0.6)\ V = 1.6\ V[/math]

So to get this operating point I need to set up [math]V_{B} = 1.6\ V[/math]. I can do it using voltage divider [math]R_1/R_2[/math]. To get operating point independent of the transistor base current we want [math]I_{R1} \gg\ I_B[/math]

[math]I_B = \frac{I_C}{\beta} = \frac{5\ mA}{200} = 25\ uA[/math].

Here are have used [math]\beta = 200[/math] instead of [math]\beta = 150[/math] as in my previous lab because it's my actual values of [math]\beta[/math] here. I have measured this [math]\beta[/math] using millivoltmeter.

Let's [math]I_{R1} = 800\ uA \gg\ I_B = 25\ uA[/math]

So

[math]R_1 = \frac{V_B}{I_1} = \frac{1.6\ V}{800\ uA} = 2\ k\Omega[/math]

And [math]R_2[/math] we can find using the voltage divider formula

[math]1.6\ V = \frac{R_1}{R_1+R_2} \cdot 20\ V [/math]

So

 [math]R_2 = \frac{20-1.6}{1.6} \cdot R_2 = 23\ k\Omega[/math]

Let's check it:

[math]20\ V = \frac{2\ k\Omega}{23+2 k\Omega}\cdot 20\ V = 1.6\ V[/math] as should be.

Measure all DC voltages in the circuit and compare with the predicted values.(10 pnts)

My predicted DC voltage are:

We have from operating point:

[math]V_{EC} = 10\ V[/math] 
[math]I_C \approx I_E = 5\ mA[/math]

And because we have silicon transistor:

[math]V_{BE} = 0.6\ V [/math]

Now

[math]V_E = I_E \cdot R_E = 5\ mA \cdot 200\ \Omega = 1\ V[/math]
[math]V_C = V_E + V_{EC} = (1 + 11)\ V = 12\ V[/math]
[math]V_B = V_E + V_{BE} = (1 + 0.6)\ V = 1.6\ V[/math]

My measured DC voltage are:

[math]V_{EC} = (11.32 \pm 0.01)\ V[/math]
[math]V_{BE} = (0.69 \pm 0.01)\ V [/math]

[math]V_E = (0.87 \pm 0.01)\ V[/math]
[math]V_C = (12.19 \pm 0.01)\ V[/math]
[math]V_B = (1.56 \pm 0.01)\ V[/math]

First note that my [math]V_B = (1.56 \pm 0.01)\ V[/math] is close to predicted values [math]V_B = 1.6\ V[/math]. And it because I was able to get good voltage divider. I get [math]R_1 = (1.98 \pm 0.01) k\Omega[/math], [math]R_2 = (22.9 \pm 0.1) k\Omega[/math].

So

[math]V_B = \frac{1.98 \pm 0.01 \k\Omega}{(1.98 \pm 0.01 + 22.9 \pm 0.1)\ k\Omega} \cdot (20 \pm 0.1)\ V[/math]

Measure [math]R_{in}[/math] and [math]R_{out}[/math] at about 1 kHz and compare to the theoretical value.(10 pnts)

How do you do this? Add resistor in front of [math]C_1[/math] which you vary to determine [math]R_{in}[/math] and then do a similar thing for [math]R_{out}[/math] except the variable reistor goes from [math]C_2[/math] to ground.

Questions

1. Why does a flat load line produce a high voltage gain and a steep load line a high current gain? (10 pnts)
2. What would be a good operating point an an [math]npn[/math] common emitter amplifier used to amplify negative pulses?(10 pnts)
3. What will the values of [math]V_C[/math], [math]V_E[/math] , and [math]I_C[/math] be if the transistor burns out resulting in infinite resistance. Check with measurement.(10 pnts)
4. What will the values of [math]V_C[/math], [math]V_E[/math] , and [math]I_C[/math] be if the transistor burns out resulting in near ZERO resistance (ie short). Check with measurement.(10 pnts)
5. Predict the change in the value of [math]R_{in}[/math] if [math]I_D[/math] is increased from 10 [math]I_B[/math] to 50 [math]I_B[/math](10 pnts)
6. Sketch the AC equivalent circuit of the common emitter amplifier.(10 pnts)

Go Back to All Lab Reports Forest_Electronic_Instrumentation_and_Measurement