Pair Production Rate Calculation

Go Back

LINAC parameters used in calculations

1) pulse width 50 ps
2) pulse current 50 A
3) repetition rate 300 Hz
4) energy 44 MeV

Number of electrons/sec on radiator

[math] 50\ \frac{C}{sec} \times \frac{1\cdot e^-}{1.6\cdot 10^{-19}\ C} \times 50\ \mbox{ps} \times 300\ \mbox{Hz} = 0.47 \cdot 10^{13}\ \frac{e^-}{sec}[/math]

Number of photons/sec out of radiator

1/2 mil of Ti

1. [math]\sigma_{brems}=0.1\ \mbox{photons/electrons/MeV/r.l}[/math]
2. [math]\mbox{r.l.(Ti)} = 3.59\ \mbox{cm}[/math]
3. [math]\mbox{radiator}\ \mbox{thickness} = 12.5\ \mu m[/math]

[math]\frac{12.5\ \mu m}{3.59\ cm} = 3.48 \cdot 10^{-4}\ r.l.[/math]

[math]0.47 \cdot 10^{13}\ \frac{e^-}{sec} \times 0.1\ \frac{\gamma 's}{(e^- \cdot MeV \cdot r.l.)} \times 3.48 \cdot 10^{-4}\ r.l. \times 10\ MeV =1.63 \cdot 10^{9} \frac{\gamma}{sec}[/math]

Alex factor is 6.85 %

[math]1.63 \cdot 10^{9} \frac{\gamma}{sec} \cdot 6.85\ % = 1.12 \cdot 10^{8} \frac{\gamma}{sec}[/math]

1/2 mil of Al

1. [math]\sigma_{brems}=xxx\ \mbox{photons/electrons/MeV/r.l}[/math]
2. [math]\mbox{r.l.(Ti)} = 8.89\ \mbox{cm}[/math]
3. [math]\mbox{radiator}\ \mbox{thickness} = 12.5\ \mu m[/math]

[math]\frac{12.5\ \mu m}{8.89\ cm} = 1.41 \cdot 10^{-4}\ r.l.[/math]

[math]0.47 \cdot 10^{13}\ \frac{e^-}{sec} \times xxx\ \frac{\gamma 's}{(e^- \cdot MeV \cdot r.l.)} \times 1.41 \cdot 10^{-4}\ r.l. \times 10\ MeV =xxx \cdot 10^{9} \frac{\gamma}{sec}[/math]

Alex factor is 6.85 %

[math]xxx \cdot 10^{9} \frac{\gamma}{sec} \cdot 6.85\ % = xxx \cdot 10^{8} \frac{\gamma}{sec}[/math]

Conversion factor from Ti to Al

All my following calculation for pair production rate are based on (1/2) mil of Ti radiator. If we want to recalculate for (1/2) mil of Al converter we need to use conversion factor:

[math]/frac{}{}[/math]

Pair production rate

out of Al converter

[math]\sigma_{pairs} = 0.5\ \frac{\mbox{barns}}{\mbox{atom}}[/math]

[math]l = 3.0\ \mu m[/math] (by varying width we can vary the yield)

[math]N_{Al} = \frac{2.70\ \frac{g}{cm^3} \times 6.02 \cdot 10^{23}\ \frac{atoms}{mol} \times 3.0\ \mu m} {26.98\ \frac{g}{mol}} = 1.81 \cdot 10^{23}\ \frac{\mbox{atoms}}{m^2}[/math]

[math]\frac {1.12 \cdot 10^{8}\ \frac{\gamma}{sec} \times \sigma_{pairs} \times N_{Al}} {f} = 3.38\ \frac{\mbox{pairs}}{\mbox{pulse}} [/math]

through 1 m of air

Assume air consists entirely from Nitrogen:

[math]\sigma_{pairs}\ (\mbox{Nitrogen}) = 0.15\ \frac{\mbox{barns}}{\mbox{atom}}[/math] 

[math]l = 1.0\ \mbox{m}[/math]

[math]N_{\mbox{Nitrogen}} = \frac{0.00125\ \frac{g}{cm^3} \times 6.02 \cdot 10^{23}\ \frac{atoms}{mol} \times 1.0\ \mbox{m}} {14.01\ \frac{g}{mol}} = 5.37 \cdot 10^{25}\ \frac{\mbox{atoms}}{m^2}[/math]

[math]\frac {1.12 \cdot 10^{8}\ \frac{\gamma}{sec} \times \sigma_{pairs} \times N_{Al}} {f} = 300\ \frac{\mbox{pairs}}{\mbox{pulse}} [/math]

Appendix

pair production cross sections in an Al target

Ref. Geant4 and Theoretical Pair Production Cross Sections for 1 MeV - 100 GeV photons in Aluminum. Vakho Makarashvili, December 18, 2007

pair production cross sections in a Nitrogen

Ref. Photon Cross Section, Attenuation Coefficients, and Energy Absorption Coefficients From 10 keV to 100 Gev. J.H.Hubbell. Center for Radiation Research.National Bureau of Standards. Washington, D.C. 20234

Here I just plotted the table above for pair production cross section in (0, 40) MeV energy region

Go Back