Difference between revisions of "MiniDC PreampOutput 10 10 07"

From New IAC Wiki
Jump to navigation Jump to search
Line 31: Line 31:
  
 
I found that a trigger threshold of -100 mV on the preamp ouput shown on scope channel #2 discriminated well (but not perfectly:see pictures 2 & 3 below) between noise and pulses consistent with previous ionization events.
 
I found that a trigger threshold of -100 mV on the preamp ouput shown on scope channel #2 discriminated well (but not perfectly:see pictures 2 & 3 below) between noise and pulses consistent with previous ionization events.
 
 
[http://iac.isu.edu/mediawiki/index.php/Mini-prototype Back to Mini prototype page]
 
  
  
Line 45: Line 42:
 
[[Image:MINIDC_Sense-Preamp_Output_10-10-07_AmpTrig7.jpg | 200 px]]
 
[[Image:MINIDC_Sense-Preamp_Output_10-10-07_AmpTrig7.jpg | 200 px]]
 
[[Image:MINIDC_Sense-Preamp_Output_10-10-07_AmpTrig8.jpg | 200 px]]
 
[[Image:MINIDC_Sense-Preamp_Output_10-10-07_AmpTrig8.jpg | 200 px]]
 +
 +
 +
 +
[http://iac.isu.edu/mediawiki/index.php/Mini-prototype Back to Mini prototype page]

Revision as of 16:59, 16 October 2007

Preamp output

The following scope pictures were taken as the preamp board was being powered on. The Drift chamber High Voltage was off but all cabling (grounds) were conencted.

Drift chamber High voltage settings

HV settings
Wire Volts
Sense 1800
Field -800
Guard 800

I should have set the Field and Guard wires to 900 volts according to Mac's e-mail reporting his Garfield simulation results. Next time.

Scope pictures triggering on sense wire C2

I set the scope trigger threshold to below -14 mV on Ch 1 based on previous measurements. Sense wire 2 is plugged into Channel 1 on the scope and the preamp output for channel 2 (Pin #2) is connected to channels 2 of the scope.


MINIDC Sense-Preamp Output 10-10-07 SenseTrig1.jpg MINIDC Sense-Preamp Output 10-10-07 SenseTrig2.jpg MINIDC Sense-Preamp Output 10-10-07 SenseTrig3.jpg MINIDC Sense-Preamp Output 10-10-07 SenseTrig4.jpg MINIDC Sense-Preamp Output 10-10-07 SenseTrig5.jpg

Scope pictures triggering on preamp output (pin 2)

I found that a trigger threshold of -100 mV on the preamp ouput shown on scope channel #2 discriminated well (but not perfectly:see pictures 2 & 3 below) between noise and pulses consistent with previous ionization events.


MINIDC Sense-Preamp Output 10-10-07 AmpTrig1.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig2.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig3.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig4.jpg

MINIDC Sense-Preamp Output 10-10-07 AmpTrig5.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig6.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig7.jpg MINIDC Sense-Preamp Output 10-10-07 AmpTrig8.jpg


Back to Mini prototype page