Difference between revisions of "Sadiq Proposal Defense"

From New IAC Wiki
Jump to navigation Jump to search
 
(65 intermediate revisions by 2 users not shown)
Line 1: Line 1:
I propose a measurement of the positron production efficiency using a quad triple collection system.  The quad triplet collection system was proposed by ...  A previous experiment at the IAC observed positrons.  I have optimized a beam line to improve that experiment and will quantify the positron production efficiency.
+
[[File:sadiq_proposal.pdf]]
  
= Abstract =
 
  
I propose to use an quadrupole triplet system to measure positron production efficiency at the High Rep Rate Linac (HRRL) at  Idaho State University's (ISU) Idaho Accelerator Center (IAC). In the previous experiment conducted at IAC, we observed positrons. Dr. G. Stancari proposed to use quadrupole triplet system to collect positrons. Positrons produced at the target has wide spread of momentum and divergence. Using triplet system we can focus positron beam, thus increase our efficiency. HRRL cavity is relocated and new beamline is setup to use quadrupole triplet system. I also intend to perform simulations to study optimum beamline settings before running experiment. I want to use NaI detectors to measure and quantify the positrons.
+
= text =
 +
%% The comment character in TeX / LaTeX is the percent character.
 +
%% The following chunk is called the header
  
= Introduction =
+
\documentclass{article} % essential first line
 +
\usepackage{float} % this is to place figures where requested!
 +
\usepackage{times} % this uses fonts which will look nice in PDF format
 +
\usepackage{graphicx} % needed for the figures
 +
\usepackage{url}
  
== New Beamline ==
+
\usepackage{rotating}
 +
\usepackage[none]{hyphenat}
 +
\usepackage{booktabs}
 +
\usepackage{epstopdf}
 +
\usepackage{subfig}
 +
\usepackage{graphicx}
 +
\usepackage{amstext}
 +
%\usepackage{hyperref}
 +
%\usepackage[bottom]{footmisc}
 +
%\usepackage{tabularx }
 +
%\usepackage{footnote}
 +
%\usepackage{caption}
 +
%\usepackage{subcaption}
  
I propose a measurement of the positron production efficiency using the High Repetition Rate Linac (HRRL) located at the Beam Lab of the Physics Department, at Idaho State University (ISU).  HRRL is a S-band electron linac located in the Beam Lab of the Physics Department at Idaho State University (ISU). It is one the 15 small size linacs dedicated for nuclear application operated by the IAC. HRRL can provide electron beam with energies between 3 MeV and 16 MeV, and Maximum repetition rate of 1 kHz. HRRL beamline had recently been reconfigured to generate and collect positrons, while it still can provide electron beam with improved quality.
+
%\usepackage{epsfig}
More details about HRRL is shown in Table 1.
 
  
{| border="3"  cellpadding="5" cellspacing="0"
+
\tolerance=1 % no hyphenation, no zig-zag line.
| Beam Energy ||Max Peak Current || Repetition Rate ||Max Pulse Length
+
\emergencystretch=\maxdimen % no hyphenation, no zig-zag line.
|-
+
\hyphenpenalty=10000 % no hyphenation, no zig-zag line.
| 16 MeV || 80 mA || 1 kHz || 250 ns (FWHM)
+
\hbadness=10000 % no hyphenation, no zig-zag line.
|}
 
New beamlien first designed by Dr. G. Stancari, it uses quadrupole triplet to collect positrons. The design further optimized by Dr. Y Kim, and J.Ellis. Beamline is constructed, as shown in Fig. 1, in the Beam Lab which is located in the basement of ISU physical sciences complex. Beam Lab is divided into two parts by a L-shaped cement wall. The accelerator cell houses the cavity and magntic elements needed to transport electrons to an experimental cell. The experimental cell is located in an adjacent room to the accelerator cell. The HRRL beamline was reconfigured into an achromat by moving the accelerator cavity to accomdate two dipoles and a system of quadrupole magnets optimized for collecting positrons.
 
  
In the new beamline, the electron beam exits the HRRL cavity and passes through first the set of quadruple triplet magnets which will be used to focus the electron beam onto the positron target. Positrons produced from the positron target will be collected by second set of quadruple triplet that will be optimized to collect positrons.  The first dipole magnet bends the positrons or electrons, depending on the polarity setting, by 45 degrees towards a second dipole magnet. The second dipole will bend the beam another 45 degrees, thus completes a 90 degree bend. A third quadruple triplet will be used focus the e-/e+ beam, as users desired.
+
%\restylefloat{figure}
 +
\floatstyle{ruled}
 +
\newfloat{program}{thp}{lop}
 +
\floatname{program}{Program}
 +
%\floatstyle{boxed}
  
[[Image:BeamLine_Yim_10-14-10.png| 450 px |thumb | Fig. HRRL beamline for positron generation.]]
+
%\renewcommand{\topfraction}{0.85}
 +
%\renewcommand{\textfraction}{0.1}
  
{| border="1" cellpadding="4"
 
|-
 
|Item || Description
 
|-
 
| T1 || Positron target
 
|-
 
| T2 || Annihilation target
 
|-
 
| EnS || Energy Slit
 
|-
 
| F1, F2, F3 || Flang
 
|-
 
| FC1, FC2  || Faraday Cup
 
|-
 
| Q1,...Q10 || Quadrupole
 
|-
 
| D1, D2 || Dipole
 
|-
 
| NaI || NaI Detecotrs
 
|-
 
| OTR || OTR screen
 
|-
 
| YAG || YAG screen
 
|}
 
  
== Earlier measurements ==
+
%\usepackage{lipsum}% http://ctan.org/pkg/lipsum
 +
%\usepackage[demo]{graphicx}% http://ctan.org/pkg/graphicx
  
Earlier measurements were conducted at Idaho Accelerator Center of ISU, May of 2008. Setup are shown in figure below. 511 keV photons from annihilation were detected.
+
%% Here I adjust the margins
  
{| border="1"  |cellpadding="20" cellspacing="0  
+
\oddsidemargin -0.25in % Left margin is 1in + this value
|-
+
\textwidth 6.75in % Right margin is not set explicitly
|Run # || MPA file name || W || Ta || Description
+
%\topmargin 0in % Top margin is 1in + this value
|-
+
\topmargin -1in % Top margin is 0in + this value
|60|| NaI060.mpa || IN || In|| Dipole at 3 MeV (1.44 on Pot), 300 Hz rep rate, (802 set to 15.7 kV,  27<math>\pm</math>6  counts at 500 keV, Live=600 seconds, grid = 1.64, Gun = 3 kV.
+
\textheight 9in % Bottom margin is not set explicitly
|}
+
\columnsep 0.25in % separation between columns
 +
%\setlength{\parindent}{15pt}  
  
{| border="1" cellpadding="4"
+
%% Define a macro for inserting postscript images
|-
+
%% ==============================================
|Item || Description
+
%% This is a macro which nominally takes 3 parameters,
|-
+
%% it would be used as follows to insert and encapsulated postscript
|[http://en.wikipedia.org/wiki/Tantalum Tantalum] Foil|| 6 mm thick 20 mm x 20 mm area
+
%% image at the location where it is used.
|-
+
%%
|[http://en.wikipedia.org/wiki/Tungsten Tungsten] Foil|| 2 mm thick 20 mm x 20 mm area
+
%% \EPSFIG{epsfilename}{caption}{label}
|-
+
%% - epsfilename is the name of the encapsulated postscript file to be
|[http://en.wikipedia.org/wiki/Phosphorus Phosphorus] Flag|| 1 mil aluminum backing
+
%%              inserted at this location
|-
+
%% - caption is the text to be shown as the figure caption, it will be
|[[Media:HpGe_Crystal_GEM-60195-Plus-P.pdf]]|| 81.3mm Diameter, 55.5mm Length
+
%%          prepended by Figure X. The number X can be referenced
|-
+
%%          using the label parameter.
|NaI detector||
+
%% - label is a name given to the figure, it can be referenced using the
|}
+
%%        \ref{label} command.
  
{| border="1" cellpadding="4"
+
\def\EPSFIG[#1]#2#3#4{ % Don't be scared by this monsrosity
|-
+
\begin{figure}[H] % it is a macro to save typing later
|[[Image:Example.jpg | 200 px |thumb|Fig. Setup for 2009 run.]] || [[Image:Run60_HpGe-NaI.gif | 200 px |thumb|Fig. Spectrum from HpGe Detector and NaI detecotrs.]] || [[Image:PositronYield_SweeperMagnet_run60-61.gif | 200 px |thumb|Fig. ]]
+
\begin{center} %
|}
+
\includegraphics[#1]{#2} %
 +
\end{center} %
 +
\caption{#3} %
 +
\label{#4} %
 +
\end{figure} %
 +
} %
  
=Experiments=
 
  
== HRRL Emittance measurements ==
+
%% Define the fields to be displayed by a \maketitle command
  
Emittance is an important parameter in accelerator physics. If emittance with twiss parameters are given at the exit of the gun, we will be able to calculate beam size and divergence any point after the exit of the gun. Knowing the beam size and beam divergence on the positron target will greatly help us study the process of creating positron. Emittance with twiss parameters are also key parameters for any accelerator simulations. Also, energy and energy spread of the beam will be measured in the emittance measurement.
+
\author{Sadiq Setiniyaz (Shadike Saitiniyazi)\thanks{Email: sadik82@gmail.com}}
 +
%{address={Department of Physics, Idaho State University}}
 +
\title{PROPOSAL FOR POSITRON PRODUCTION EFFICIENCY STUDY USING HIGH REPETITION RATE LINAC AT IAC}
  
=== What is Emittance ===
+
%%
[[image:sadiq_phd_emittance_phase_space_ellipse.png | 200 px |thumb |Fig.1 Phase space ellipse <ref name="MConte08"></ref>.]]
+
%% Header now finished
 +
%%
  
In accelerator physics, Cartesian coordinate system was used to describe motion of the accelerated particles. Usually the z-axis of Cartesian coordinate system is set to be along the electron beam line as longitudinal beam direction. X-axis is set to be horizontal and perpendicular to the longitudinal direction, as one of the transverse beam direction. Y-axis is set to be vertical and perpendicular to the longitudinal direction, as another transverse beam direction.
+
\begin{document} % Critical
 +
\twocolumn
 +
\thispagestyle{empty} % Inhibit the page number on this page
 +
\maketitle % Use the \author, \title and \date info
  
For the convenience of representation, we use <math>z</math> to represent our transverse coordinates, while discussing emittance. And we would like to express longitudinal beam direction with <math>s</math>. Our transverse beam profile changes along the beam line, it makes <math>z</math> is function of <math>s</math>, <math>z~(s)</math>. The angle of a accelerated charge regarding the designed orbit can be defined as:
+
%% Next comes the abstract, notice the curly-braces surrounding the
 +
%% text.
  
<math>z'=\frac{dz}{ds}</math>
+
\abstract{
 +
\indent
  
If we plot <math>z</math> vs. <math>z'</math>, we will get an ellipse. The area of the ellipse is an invariant, which is called Courant-Snyder invariant. The transverse emittance <math>\epsilon</math> of the beam is defined to be the area of the ellipse, which contains 90% of the particles <ref name="MConte08"> M. Conte and W. W. MacKay, “An Introduction To The Physics Of Particle Accelera
+
I propose to measure the positron production efficiency for a positron source that uses a quadrupole triplet system to collect positrons from a tungsten target that are produced when the target is impinged by electrons from the High Repetition Rate Linac (HRRL) at Idaho State University's (ISU) Idaho Accelerator Center (IAC). Positrons were observed in May of 2008 at the IAC without the use of a quadrupole triplet collection system. When a 10~MeV electron beam is used on the tungsten target, positrons escaping from the downstream side of the tungsten have a wide momentum spread of 0 to 2~MeV and a large divergence of $\pi$ rad. A quad triplet collection system, after the tungsten target, is used to focus the positron beam and as a result increase our positron collection efficiency. I will install the collection system and associated beam line components and measure the positron production efficiency using the HRRL.}
tors”, World Scientifc, Singapore, 2008, 2nd Edition, pp. 257-330. </ref>.
 
  
By changing quadrupole magnetic field strength <math>k</math>, we can change beam sizes <math>\sigma_{x,y}</math> on the screen. We make projection to the x, y axes, then fit them with Gaussian fittings to extract rms beam sizes, then plot vs <math>\sigma_{x,y}</math> vs <math>k_{1}L</math>. By Fitting a parabola we can find constants
+
\section{Introduction}
<math>A</math>,<math>B</math>, and <math>C</math>, and get emittances.
+
\indent
  
===Emittance Measurement Using a YaG crystal ===
+
I propose to measure the positron production efficiency for a positron source that uses a quadrupole triplet system to collect positrons from a tungsten target that are produced when the target is impinged by electrons from the HRRL. A polarized positron source, as a new probe to explore nuclear and particle physics at Jefferson Lab, is being studied at the Continuous Electron Beam Accelerator Facility (CEBAF). While their main mission is to optimize polarization, ISU's goal is to optimize positron production efficiency. Additionally, a positron beamline at ISU is also a potential tool for nuclear physics studies. I have measured the emittance of the HRRL electron beam and constructed PMT bases for four NaI detectors. I will install the collection system and associated beam line components to measure the positron production efficiency using the HRRL.
In July 2010y, Emittance measurement of HRRL was conducted at Beam Lab, at Physics Department of ISU. I installed a YAG crystal on the HRRL beam line to see electron beam shape. A quadrupole magnet was installed between HRRL gun and the YAG screen. I changed current on the quadrupole to control magnetic field strength of the quadrupole magnet, this changed electron beam shape on the YAG screen.
 
  
==== Experimental Setup ====
+
\section{Previous Measurements}
 +
\indent
  
I did quadrupole scan to measure emittance of the electron beam in HRRL. In quadrupole scan method, the strength of the quadrupole magnet was changed by changing the current go through quadrupole coils. The electron beam were coming out of the gun went through quadrupole, then beam would enter a 3-way cross. Two end of the 3-way cross was installed on the beam line. The third end of the 3-way cross was placed upward and there was a actuator installed to it. The YAG crystal was mounted in the actuator, which can put the YAG in the beam line or take it out of the beam line. A camera was placed inside the actuator to look through vacuum a window and to capture the image on the YAG crystal created by electron beam. A Faraday cup was mounted at the end of the beam line to measure the transmission of the charge.
+
Earlier positron production measurements were conducted at ISU's IAC in the May of 2008. The setup is shown in Fig.~\ref{fig:2008-pos-beamline} and the beamline elements are described in Table~\ref{tab:2008-pos-beamline-elements}. The accelerator was operated at a 300~Hz repetition rate and 10~MeV energy. Electrons were bent by the first dipole and sent to a 2~mm thick tungsten target. Any positrons produced were focused using two quadrupoles and bent 45 degrees by a second dipole which was set to transport 3~MeV positrons. Positrons were transported to the end of the linac where they annihilated in a Ta target. A HpGe and a NaI detector were used to detect the 511~keV positrons produced as a result of annihilation. Fig.~\ref{fig:2008-spectrum} shows the spectrum taken over a 600 second time interval.
  
Setup and beam line and are shown in figures 1.2 and 1.3:
 
  
{| border="0" style="background:transparent;"  align="center"
+
\begin{figure}[htbp]
|-
+
\centering
|
+
\includegraphics[width=80mm]{2008_positron_measurement_at_IAC.eps}
[[image:sadiq_phd_emittance_HRRL_July_Emit_Lay_Out.png | 470 px |thumb|Fig.2 Experiment set up of HRRL 2010 July emittance test.]]
+
\caption{The HRRL beamline configured for positron production at IAC in 2008. }
|
+
\label{fig:2008-pos-beamline}
[[image:Constructed Beam Line for Emittance Test 1.jpg | 300 px |thumb|Fig.3 Beam Line of HRRL 2010 July emittance test.]]
+
\end{figure}
|}
 
  
 +
\begin{table}[htbp]
 +
\caption{Beamline elements for positron production at IAC in 2008.}
  
Figures 4, 5, and 6 show Faraday cup, Quadrupole Magnet, and YAG Chrystal used in the test:
+
\begin{tabular}{ll}
 +
\hline
 +
      \textbf{Item} & {$\textbf {Description}$} \\
 +
\hline
 +
          Tantalum foil  &  6 mm thick 20 mm x 20 mm area  \\
 +
          Tungsten foil  &  2 mm thick 20 mm x 20 mm area    \\
 +
          Phosphorus flag  & 1 mil aluminum backing            \\
 +
          HpGe detector & 81.3mm Diameter, 55.5mm Length \\
 +
          %NaI detector &
 +
\hline
 +
\end{tabular}
 +
\label{tab:2008-pos-beamline-elements}
 +
\end{table}
  
{| border="0" style="background:transparent;"  align="center"
+
\begin{figure}[htbp]
|-
+
\centering
|
+
  \includegraphics*[scale=0.45]{2008_Run60_HpGe-NaI}
[[image:Beam_Line_Parts_HRRL_Emittance_Test_FC.jpg | 280 px |thumb|Fig.4 Faraday cup used for HRRL 2010 July emittance test.]]
+
\caption{Spectrum from HpGe Detector and NaI detecotrs.}
|
+
\label{fig:2008-spectrum}
[[image:Beam_Line_Parts_HRRL_Emittance_Test_QuadT1.jpg | 200 px |thumb|Fig.5 Quadrupole Magnet used for HRRL 2010 July emittance test.]]
+
\end{figure}
|
 
[[image:Beam_Line_Parts_HRRL_Emittance_Test_YAG.jpg | 240 px |thumb|Fig.6 YAG Christal used for HRRL 2010 July emittance test.]]
 
|}
 
  
 +
%\begin{figure}[htbp]
 +
%\centering
 +
%  \includegraphics[scale=0.45]{2008_PositronYield_SweeperMagnet_run60-61}
 +
%\caption{Spectrum.}
 +
%\label{fig:2008-spectrum-zoom}
 +
%\end{figure}
  
  
Emittance measurement was carried out on HRRL on July of 2010 under the experimental setup discussed in previous section. In this measurement I used analog camera to take images.
+
\section{Proposed Beamline}
 +
\indent
  
When relativistic electron beam pass through YAG target, Opitcal Transition Radiation (OTR) is produced. OTR are taken for different quadrupole coil current (0-20 A).
 
  
 +
I propose a measurement of the positron production efficiency using the HRRL. The HRRL can provide electron beams with energies between 3~MeV and 16~MeV, and a maximum repetition rate of 300~Hz. The HRRL beamline has recently been reconfigured to generate and collect positrons, see Fig.~\ref{fig:HRRL-e+-line} and Table~\ref{tab:hrrl}.
  
{| border="0" style="background:transparent;" align="center"
+
\begin{table}[hbt]
|-
+
  \centering
| [[image:HRRL_Emit_test_Quad_Scan_First_0Amp.jpg | 300 px |thumb|Fig. OTR image of 0 Amp quadrupole coil current.]] ||[[image:HRRL_Emit_test_Quad_Scan_First_5Amp.jpg | 300 px |thumb|Fig. OTR image of 5 Amp quadrupole coil current.]] ||[[image:HRRL_Emit_test_Quad_Scan_First_10Amp.jpg | 300 px |thumb|Fig. OTR image of 10 Amp quadrupole coil current.]]
+
  \caption{Operational Parameters of The HRRL Linac.}
|-
+
  \begin{tabular}{lccc}
|[[image:HRRL_Emit_test_Quad_Scan_First_15Amp.jpg | 300 px |thumb|Fig. OTR image of 15 Amp quadrupole coil current.]] ||[[image:HRRL_Emit_test_Quad_Scan_First_20Amp.jpg | 300 px |thumb|Fig. OTR image of 20 Amp quadrupole coil current.]] ||
+
      \toprule
[[image:HRRL_Emit_test_Quad_Scan_Second_10Amp_2.jpg | 300 px |thumb|Fig. OTR image of -10 Amp quadrupole coil current.]]
+
      Parameter    & Unit  & Value \\
|}
+
      \midrule
 +
        maximum electron beam energy $E$  & MeV    & 16  \\
 +
      \midrule
 +
      electron beam peak current $I_{\textnormal{peak}}$ &  mA      &  80    \\
 +
        \midrule
 +
        macro-pulse repetition rate                  &  Hz      &  300 \\
 +
        \midrule
 +
        macro-pulse pulse length (FWHM)          &  ns      &  250    \\
 +
        \midrule
 +
        rms energy spread                                &  \%      &  4.23  \\
 +
  \bottomrule
 +
\end{tabular}
 +
\label{tab:hrrl}
 +
\end{table}
  
==== Data Analysis ====
+
The new beamline was first designed by Dr. G. Stancari to use a quadrupole triplet system to collect positrons~\cite{stancari}. The design was further optimized by Dr. Y Kim. The final design of the beamline is shown in Fig.~\ref{fig:HRRL-e+-line}. The HRRL accelerator room is divided into two parts by an L-shaped cement wall. The accelerator cell houses the cavity and other elements needed to transport electrons to an experimental cell. The experimental cell is located in a room adjacent to the accelerator cell. The HRRL beamline was reconfigured into an achromat by moving the accelerator cavity to accommodate two dipoles and a system of quadrupole magnets optimized for collecting positrons.
  
[[image:Fit_Rotated_HRRL_Emit_test_Quad_Scan_Second_2Amp.jpg |thumb | 300 px |thumb|Fig. Gaussian fits for OTR images.]]
+
In the new beamline, shown in Fig.~\ref{fig:HRRL-e+-line}, the electron beam exits the cavity and passes through a quadruple triplet  that will focus the electron beam onto the positron target. Positrons produced from the positron target will be collected by the second quadruple triplet that will be optimized to collect positrons. The first dipole magnet bends the positrons/electrons, depending on the magnet polarity, by 45 degrees towards the second dipole magnet. The second dipole will bend the beam another 45 degrees, thus completing a 90 degree bend. A third quadruple triplet will focus the e-/e+ beam, as users desire. All beam elements are described in Table~\ref{tab:new-hrrl-line-elements}.
  
In the mages we can see a bright spot at the center. This spot did not change by changing quad coil current. So, this is image of hot filament. The bigger spot at the right side of the filament was changing by changing quad coil current, hence it is OTR. We also see 10 mm circle mounted on the OTR target, as well as beam hallow.
 
  
I did Guassian fits to beam image to extract x, y RMS values for different quad currents. I found out that the camera was rotated slightly. To compensate for it, images were rotated back, and I had beam image upright. To reduce back ground, I just focused on OTR beam image and took out the filament spot from data, as shown in image below.
 
  
==== Results ====
+
%\begin{figure*}[htbp]
 +
\begin{sidewaysfigure*}[htbp]
  
{| border="0" style="background:transparent;"  align="center"
+
\centering
|-
+
%\includegraphics[scale=0.28]{HRRL_Pos_and_Ele_Go}
|
+
\includegraphics[scale=0.35]{HRRL_Pos_and_Ele_Go.eps}
[[image:HRRL_Emitt_2010_Jul_Refit_After_Correcting_Calibration_Projection_X.png | 300 px |thumb|Fig. Square of RMS beam size <math> \sigma_x^2 </math> vs. quad strength times quad pole length <math> k_1L </math> for x projection of electron beam profile ]]
+
\caption{The new HRRL beamline cofiguration for positron generation.}
|
+
\label{fig:HRRL-e+-line}
[[image:HRRL_Emitt_2010_Jul_Refit_After_Correcting_Calibration_Projection_Y.png | 300 px |thumb|Fig. Square of RMS beam size <math> \sigma_x^2 </math> vs. quad strength times quad pole length <math> k_1L </math> for y projection of electron beam profile ]]
+
\end{sidewaysfigure*}
|}
 
  
 +
%\end{figure*}
  
<math> \sigma_x^2= (8.05  \pm 0.25) + (4.18 \pm 0.19)k_1L + (0.64 \pm 0.034)(k_1L)^2 </math>
 
  
<math> \epsilon_x = 2.2 \pm 1.3~mm*mrad ~\Rightarrow~ \epsilon_{n,x} = 42.4 \pm 25.4~mm*mrad</math>
 
  
<math> \beta_x=0.72 \pm 0.31, \alpha_x=-1.23 \pm 0.56 </math>
+
\begin{table}[hbt]
 +
  \centering
 +
  \caption{The new HRRL positron beamline elements.}
 +
  \begin{tabular}{lccc}
 +
      \toprule
 +
        Item  &  Description \\
 +
      \midrule
 +
        T1    & Positron target \\
 +
      \midrule
 +
        T2    &  Annihilation target \\
 +
        \midrule
 +
        EnS    & Energy Slit  \\
 +
        \midrule
 +
        FC1, FC2& Faraday Cups \\
 +
        \midrule
 +
        Q1,...Q10     & Quadrupoles \\
 +
        \midrule
 +
          D1, D2     & Dipoles \\
 +
        \midrule
 +
        NaI    &  NaI Detecotrs \\
 +
        \midrule
 +
        OTR    &  Optical Transition Radiaiton screen\\
 +
        \midrule
 +
        YAG    & Yttrium Aluminium Garnet screen\\
 +
  \bottomrule
 +
\end{tabular}
 +
\label{tab:new-hrrl-line-elements}
 +
\end{table}
  
 +
%00000000000000000000000000000000000000000000000000000000000
 +
\section{Preparation for the Positron \\ Production Experiment}
 +
\subsection{HRRL Emittance measurements}
 +
\indent
  
<math>\sigma_y^2 = (8.52 \pm 0.40) + (-3.88 \pm 0.28)k_1L + (0.57 \pm 0.048)(k_1L)^2 </math>
 
  
<math> \epsilon_y = 2.6 \pm 2.0~mm*mrad  ~\Rightarrow~  \epsilon_{n,y} = 50.5 \pm 38.3~mm*mrad</math>
+
Emittance, a key parameter in accelerator physics, is used to quantify the quality of an electron beam produced by an accelerator. The beam size and divergence at any point in the beamline can be described using emittance and Twiss parameters.  
  
<math> \beta_y=0.54 \pm 0.22, \alpha_y=2.68 \pm 1.13 </math>
+
An Optical Transition Radiation (OTR) based viewer was installed to allow measurements at the high electron currents available from the HRRL. The visible light from the OTR based viewer is produced when a relativistic electron beam crosses the boundary of two mediums with different dielectric constants.  Visible radiation is emitted at an angle of 90${^\circ}$ with respect to the incident beam direction~\cite{OTR} when the electron beam intersects the OTR target at a 45${^\circ}$ angle. These emitted photons are observed using a digital camera and can be used to measure the shape and intensity of the electron beam based on the OTR distribution.
  
=== Emittance Measurements with an OTR ===
+
The emittance of the HRRL was measured to be less than 0.4~$\mu$m using the OTR based tool at an energy of 15~MeV.  The details of this emittance measurement using the quadrupole scanning method were described in the IPAC12 proceedings~\cite{setiniyaz-q-scan}. The results are summarized in Table~\ref{results}.
  
During first emittance measurement, we see our electron beam image at YAG crystal is much bigger than expected. Comparison study shows that for same beam YAG screen shows bigger beam size than Optical Transition Radiation (OTR) screen. Yag is good for low charge beam. Electron beam from HRRL has a big charge in a single pulse and beam size is big.  
+
\begin{table}[hbt]
 +
  \centering
 +
  \caption{Emittance Measurement Results.}
 +
  \begin{tabular}{lcc}
 +
      \toprule
 +
        {Parameter}        & {Unit}    &    {Value}    \\
 +
      \midrule
 +
        projected emittance $\epsilon_x$        &  $\mu$m    &    $0.37 \pm 0.02$    \\
 +
          projected emittance $\epsilon_y$            &  $\mu$m    &    $0.30 \pm 0.04$    \\
 +
%   normalized \footnote{normalization procedure assumes appropriate beam chromaticity.} emittance $\epsilon_{n,x}$  &  $\mu$m    &  $10.10 \pm 0.51$        \\
 +
  %normalized emittance $\epsilon_{n,y}$      &  $\mu$m    &  $8.06 \pm 1.1$          \\
 +
        $\beta_x$-function                            &  m                          &  $1.40  \pm  0.06$          \\
 +
        $\beta_y$-function                                &  m                          &  $1.17  \pm 0.13$        \\
 +
  $\alpha_x$-function                          &  rad                        &  $0.97  \pm  0.06$          \\
 +
  $\alpha_y$-function                              &  rad                        &  $0.24  \pm 0.07$        \\
 +
    micro-pulse charge                                     &  pC                          &  11        \\
 +
    micro-pulse length                                    &  ps                          &  35          \\
 +
  energy of the beam $E$                                &  MeV                        &  15    $\pm$ 1.6    \\
 +
  relative energy spread $\Delta E/E$                                &  \%                        &  10.4        \\
 +
  \bottomrule
 +
  \end{tabular}
 +
  \label{results}
 +
\end{table}
  
I did second emittance measurement with 10 <math>\mu m</math> thick aluminium OTR screen. I also improved our optical imaging system by using better digital camera that can be triggered by the same pulse trigger electron gun. Also I used three 2-inch diameter lenses to focus the lights from OTR to the CCD of the camera.
+
\subsection{Positron Detection using NaI crystals}
 +
\indent
  
==== Experimental Setup ====
+
A tungsten target will be placed at the end of the 90 degree beamline to annihilate positrons. I want to use two NaI detectors to detect the 511~keV photons created when positrons annihilate. I acquired some NaI crystals from Idaho Accelerator Center (IAC). Since their original bases used a slow post-amplifier, I built new PMT bases. I modified the design of model PA-14 from Saint-Gobain Crystals \& Detectors Ltd. These detectors are tested, calibrated, and ready to be used for the measurement. Fig.~\ref{fig:IAC-dets} shows the crystals and the bases I built. Fig.~\ref{fig:IAC-dets-Co60-Na22-spec} shows the spectrum taken by the detector using button sources.
 +
%I expect by doing coincidence, the resolution of 511~keV peak in the spectrum will be improved.
  
[[image:hrrl_2011_mar_emit_test_quad_scan_quad.png |thumb | 400 px |thumb|Fig. Simplified setup configuration for HRRL beamline at 2011 March measurement.]]
+
\begin{figure}[htbp]
 +
\centering
 +
\includegraphics[scale=0.08]{IAC_NaI_Detectors}
 +
\caption{The NaI detector and base built.}
 +
\label{fig:IAC-dets}
 +
\end{figure}
  
The cavity was moved the new location and beam line was built by the design of Dr. Yujong Kim, as shown in figure
+
\begin{figure}[htbp]
 +
\centering
 +
\includegraphics[scale=0.18]{Na22_Co60Spectrum_by_IAC_Detectors}
 +
\caption{Detector 3 calibrated Spectrum.}
 +
\label{fig:IAC-dets-Co60-Na22-spec}
 +
\end{figure}
  
Experimental setup is shown in the following figure
+
%\subsection{Positron Target Installation}
 +
%\indent
 +
%
 +
%A step motor is ready to be installed once the vacuum chamber is ready. The step motor, shown in the Fig.~\ref{fig:step-motor}, will hold 8 tungsten targets.
 +
%
 +
%\begin{figure}[htbp]
 +
%\centering
 +
%\includegraphics[scale=0.08]{setep_motor}
 +
%\caption{Step motor for holding W targets.}
 +
%\label{fig:step-motor}
 +
%\end{figure}
  
I chose one of the quad at a time to do the scan and turned off all the other quads. Optical transition radiation was observed at OTR target. At the end of 0 degree beamline I had a Faraday cup to measure the charge of the beam. Camera cage system was located below the OTR target. There are 3 lenses used to focus lights from target to the CCD camera. Target can be pushed into or taken out of the beamline by the actuator at the top.
+
\section{Future Plan}
 +
\indent
  
OTR Target can be pushed into or taken out of the beamline vertically by the actuator at the top, which is attached to the 6-way cross. This actuator controlled remotely at the control desk.  
+
We want to produce positrons using the HRRL beam line. We can improve positron collection efficiency by applying following methods:
  
Camera cage system was located below the OTR target. Cage system attached to the bottom of the 6-way cross. Lower end of cross is a transparent window. There are 3 lenses used to focus lights from target to the CCD camera. They have focal length of 100 mm, 500 mm, and 50 mm.  
+
1. By using a quadrupole triplet before tungsten a target, we will have control over the beam size and divergence at the target.
  
The lens closest to the OTR target is 10 cm away from the target, an it has 100 mm focal length. This lens was located as close to the target as possible, so that we might collect as much OTR light as possible, and it was thus called collector lens.
+
2. Cryogenically cooled converter will be installed, and these targets will be able to take on more beam power and increase positron yield.
The lens in the middle has focal length of 500 mm. Moving this lens will change total focal length in a small amount, and this allow us to do fine tuning. Thus, we called this lens fine tuning lens.
 
The last lens, which is furthest from target, and closed to the CCD camera has the shortest focal length of 5o mm. Its short focal length allow us to focus the light on the very small sensing area of the CCD camera.  
 
  
{| border="0" style="background:transparent;"  align="center"
+
3. Positrons will be collected by the quadrupole triplet system, which will improve collection efficiency.
|-
 
| [[image: HRRL_Mar_Emit_lay_Out_Camera.png  | 500 px |thumb|Fig. HRRL beamline: Optical cage system to focus OTR lights on CCD camera.]]
 
| [[image: HRRL_Mar_Emit_lay_Out_Camera_2.png| 500 px |thumb|Fig. HRRL beamline: Optical lenses lay out for optical cage system.]]
 
|-
 
|}
 
  
==== Experiment with OTR ====
+
4. Simulations will optimize beam elements for positron collection.
  
Optical Transition Radiation (OTR): Transition radiation is emitted when a charge moving at a constant velocity cross a boundary between two materials with different dielectric constant.
+
%\bibliographystyle{unsrt} % Order by citation
 +
%\bibliography{report}
  
Emittance measurement was carried out on HRRL on March of 2011 under the experimental setup discussed in previous section. In this measurement I used JAI digital camera.  
+
\begin{thebibliography}{9}
 +
%{stancari}
 +
%@techreport{stancari,
 +
% title      ={{stancari's proposal-------}},
 +
% month      ={Nov.},
 +
% year = {2005},
 +
% author      ={J. Stancari},
 +
% address    ={Frascati, Italy},
 +
% number      ={},
 +
% institution ={DAFNE Technical Note}
 +
\bibitem{stancari}
 +
G. Stancari and T. Forest "Design of a new beamline for electrons, positrons and photons at the HRRL lab", Pocatello, ID, USA (2009).
  
When relativistic electron beam pass through Aluminum target OTR is produced. OTR are taken for different quadrupole coil currents.
 
  
{|  border="0" style="background:transparent;"  align="center"
+
%@techreport{OTR,
|-
+
% title      ={{Optical Transition Radiation}},
|[[File:OTR_Q1Scan03182011_10.png | 300 px |thumb|Fig. OTR image of 0 Amp Q1 coil current.]] ||[[File:OTR_Q1Scan03182011_15.png | 300 px |thumb|Fig. OTR image of +1 Amp Q1 coil current.]] ||
+
% month      ={},
[[File:OTR_Q1Scan03182011_20.png | 300 px |thumb|Fig. OTR image of +2 Amp Q1 coil current.]]
+
% year = {1992},
|}
+
% author      ={B. Gitter},
 +
% address    ={Los Angeles, CA 90024},
 +
% institution ={Particle Beam Physics Lab, Center for Advanced Accelerators, UCLA Department of Physics}
 +
%}
  
==== Data Analysis and Results====
+
\bibitem{OTR}
 +
B. Gitter, Tech. Rep., Los Angeles, USA (1992).
  
The projection of the beam is not Gaussian distribution. So, I fit Super Gaussian fitting <ref name="BeamDisBeyondRMS"> F.-J Decker, “Beam Distributions Beyond RMS”, BIW94, Vancouver,CA,Sep 1994, . </ref>.
+
%\bibitem{setiniyaz-q-scan}
 +
%@InProceedings{setiniyaz-q-scan,
 +
%  author = {S. Setiniyaz, K. Chouffani, T. Forest, and Y. Kim},
 +
%  title = {TRANSVERSE BEAM EMITTANCE MEASUREMENTS OF A 16 MeV LINAC AT THE IDAHO ACCELERATOR CENTER},
 +
% booktitle = {IPAC2012},%pages = {151--158},
 +
% year = 2012,
 +
% address = {New Orleans, USA}
 +
%}
 +
\bibitem{setiniyaz-q-scan}
 +
S. Setiniyaz, K. Chouffani, T. Forest, and Y. Kim, in $Proc$. $IPAC2012$, New Orleans, USA.
  
I used the MATLAB to analyze the data. The results shows that:
+
%\bibitem{emit-mat}
 +
%C.F. Eckman $et$ $al$., in $Proc$. $IPAC2012$, New Orleans, USA.
  
<math> \sigma_x^2= (3.678  \pm 0.022) + (-4.17 \pm 0.22)k_1L + (5.55 \pm 0.42)(k_1L)^2 </math>
 
  
<math> \epsilon_x = 0.417 \pm 0.023~mm*mrad ~\Rightarrow~ \epsilon_{n,x} = 11.43 \pm 0.64~mm*mrad</math>
+
\end{thebibliography}
  
<math> \beta_x=1.385 \pm 0.065, \alpha_x=0.97 \pm 0.07 </math>
+
\end{document}
 
 
<math>\sigma_y^2 = (2.843 \pm 0.044) + (1.02 \pm 0.52)k_1L + (3.8 \pm 1.2)(k_1L)^2 </math>
 
 
 
<math> \epsilon_y = 0.338 \pm 0.065~mm*mrad  ~\Rightarrow~  \epsilon_{n,y} = 9.3 \pm 1.8~mm*mrad</math>
 
 
 
<math> \beta_y=1.17 \pm 0.19, \alpha_y=0.22 \pm 0.10 </math>
 
 
 
==Beamline parameters for optimal positron production using the measured emmittance==
 
 
 
 
 
 
 
= Positron Detection using NaI crystal =
 
 
 
[[File:HRRL_Positron_Our_Modified_PMT_Base_Design.png |thumb | 350 px | Fig. NaI detector base circuit.]]
 
 
 
To detect positrons created, I want a put Tungsten target at the end of 90 degree beamline. When positrons hit W-target, 511 keV photons will be created. I want to use NaI detectors to detect these 511 keV photons, so I might have an estimate on the numbers of the positrons I collect at the end of the 90 degree beamline.
 
 
 
I acquired some NaI crystals from Idaho Accelerator Center (IAC). I built our own PMT bases for them, since their own bases not working properly. I modified the design of model PA-14 from Saint-Gobain crystals & detectors ltd. Following image is the design.
 
 
 
[[File:IAC_NaI_Detectors_and_Parts_7.png | 450 px | Fig. The NaI detector and base built.]]
 
 
 
[[File:Hrrl_pos_det_calb_det3_r2637_r2636_2.png | 450 px|Fig. Detector 3 calibrated Spectrum.]]
 
 
 
Even though now the 511 keV peak seems to be very wide and our resolution is low, I are expecting to improve these by doing coincidence in the future experiments.
 
 
 
= Future Plan =
 
 
 
== Positron Target ==
 
 
 
A tungsten target will be placed in the space between 1st and 2nd triplet. The tungsten target will be placed inside a big chamber.
 
 
 
== Emittance Tests with Energy Scan ==
 
 
 
I want to do emittance test with precise energy scan. I remapped dipole magnet for more precise energy scan. This will also improve our emittance measurement. 
 
 
 
== Positron Yield ==
 
 
 
I will insert the first tungsten target and create positrons. I am expecting to collect part these positrons and transport them down the second tungsten target at the end of the 90 degree beamline. By doing these, 511 keV photons will be created and I want to detect them by our NaI detectors.
 
 
 
= References =
 
 
 
<references/>
 
 
 
 
 
 
 
 
 
[[File:Emittance.tex]]
 

Latest revision as of 23:38, 21 August 2012

File:Sadiq proposal.pdf


text

%% The comment character in TeX / LaTeX is the percent character. %% The following chunk is called the header

\documentclass{article} % essential first line \usepackage{float} % this is to place figures where requested! \usepackage{times} % this uses fonts which will look nice in PDF format \usepackage{graphicx} % needed for the figures \usepackage{url}

\usepackage{rotating} \usepackage[none]{hyphenat} \usepackage{booktabs} \usepackage{epstopdf} \usepackage{subfig} \usepackage{graphicx} \usepackage{amstext} %\usepackage{hyperref} %\usepackage[bottom]{footmisc} %\usepackage{tabularx } %\usepackage{footnote} %\usepackage{caption} %\usepackage{subcaption}

%\usepackage{epsfig}

\tolerance=1 % no hyphenation, no zig-zag line. \emergencystretch=\maxdimen % no hyphenation, no zig-zag line. \hyphenpenalty=10000 % no hyphenation, no zig-zag line. \hbadness=10000 % no hyphenation, no zig-zag line.

%\restylefloat{figure} \floatstyle{ruled} \newfloat{program}{thp}{lop} \floatname{program}{Program} %\floatstyle{boxed}

%\renewcommand{\topfraction}{0.85} %\renewcommand{\textfraction}{0.1}


%\usepackage{lipsum}% http://ctan.org/pkg/lipsum %\usepackage[demo]{graphicx}% http://ctan.org/pkg/graphicx

%% Here I adjust the margins

\oddsidemargin -0.25in % Left margin is 1in + this value \textwidth 6.75in % Right margin is not set explicitly %\topmargin 0in % Top margin is 1in + this value \topmargin -1in % Top margin is 0in + this value \textheight 9in % Bottom margin is not set explicitly \columnsep 0.25in % separation between columns %\setlength{\parindent}{15pt}

%% Define a macro for inserting postscript images %% ============================================== %% This is a macro which nominally takes 3 parameters, %% it would be used as follows to insert and encapsulated postscript %% image at the location where it is used. %% %% \EPSFIG{epsfilename}{caption}{label} %% - epsfilename is the name of the encapsulated postscript file to be %% inserted at this location %% - caption is the text to be shown as the figure caption, it will be %% prepended by Figure X. The number X can be referenced %% using the label parameter. %% - label is a name given to the figure, it can be referenced using the %% \ref{label} command.

\def\EPSFIG[#1]#2#3#4{ % Don't be scared by this monsrosity \begin{figure}[H] % it is a macro to save typing later \begin{center} % \includegraphics[#1]{#2} % \end{center} % \caption{#3} % \label{#4} % \end{figure} % } %


%% Define the fields to be displayed by a \maketitle command

\author{Sadiq Setiniyaz (Shadike Saitiniyazi)\thanks{Email: sadik82@gmail.com}} %{address={Department of Physics, Idaho State University}} \title{PROPOSAL FOR POSITRON PRODUCTION EFFICIENCY STUDY USING HIGH REPETITION RATE LINAC AT IAC}

%% %% Header now finished %%

\begin{document} % Critical \twocolumn \thispagestyle{empty} % Inhibit the page number on this page \maketitle % Use the \author, \title and \date info

%% Next comes the abstract, notice the curly-braces surrounding the %% text.

\abstract{ \indent

I propose to measure the positron production efficiency for a positron source that uses a quadrupole triplet system to collect positrons from a tungsten target that are produced when the target is impinged by electrons from the High Repetition Rate Linac (HRRL) at Idaho State University's (ISU) Idaho Accelerator Center (IAC). Positrons were observed in May of 2008 at the IAC without the use of a quadrupole triplet collection system. When a 10~MeV electron beam is used on the tungsten target, positrons escaping from the downstream side of the tungsten have a wide momentum spread of 0 to 2~MeV and a large divergence of $\pi$ rad. A quad triplet collection system, after the tungsten target, is used to focus the positron beam and as a result increase our positron collection efficiency. I will install the collection system and associated beam line components and measure the positron production efficiency using the HRRL.}

\section{Introduction} \indent

I propose to measure the positron production efficiency for a positron source that uses a quadrupole triplet system to collect positrons from a tungsten target that are produced when the target is impinged by electrons from the HRRL. A polarized positron source, as a new probe to explore nuclear and particle physics at Jefferson Lab, is being studied at the Continuous Electron Beam Accelerator Facility (CEBAF). While their main mission is to optimize polarization, ISU's goal is to optimize positron production efficiency. Additionally, a positron beamline at ISU is also a potential tool for nuclear physics studies. I have measured the emittance of the HRRL electron beam and constructed PMT bases for four NaI detectors. I will install the collection system and associated beam line components to measure the positron production efficiency using the HRRL.

\section{Previous Measurements} \indent

Earlier positron production measurements were conducted at ISU's IAC in the May of 2008. The setup is shown in Fig.~\ref{fig:2008-pos-beamline} and the beamline elements are described in Table~\ref{tab:2008-pos-beamline-elements}. The accelerator was operated at a 300~Hz repetition rate and 10~MeV energy. Electrons were bent by the first dipole and sent to a 2~mm thick tungsten target. Any positrons produced were focused using two quadrupoles and bent 45 degrees by a second dipole which was set to transport 3~MeV positrons. Positrons were transported to the end of the linac where they annihilated in a Ta target. A HpGe and a NaI detector were used to detect the 511~keV positrons produced as a result of annihilation. Fig.~\ref{fig:2008-spectrum} shows the spectrum taken over a 600 second time interval.


\begin{figure}[htbp] \centering \includegraphics[width=80mm]{2008_positron_measurement_at_IAC.eps} \caption{The HRRL beamline configured for positron production at IAC in 2008. } \label{fig:2008-pos-beamline} \end{figure}

\begin{table}[htbp] \caption{Beamline elements for positron production at IAC in 2008.}

\begin{tabular}{ll} \hline

      \textbf{Item} & {$\textbf {Description}$} \\

\hline

          Tantalum foil   &  6 mm thick 20 mm x 20 mm area   \\
          Tungsten foil   &  2 mm thick 20 mm x 20 mm area    \\
          Phosphorus flag  & 1 mil aluminum backing             \\
          HpGe detector & 81.3mm Diameter, 55.5mm Length \\
          %NaI detector	&

\hline \end{tabular} \label{tab:2008-pos-beamline-elements} \end{table}

\begin{figure}[htbp] \centering

 \includegraphics*[scale=0.45]{2008_Run60_HpGe-NaI}

\caption{Spectrum from HpGe Detector and NaI detecotrs.} \label{fig:2008-spectrum} \end{figure}

%\begin{figure}[htbp] %\centering % \includegraphics[scale=0.45]{2008_PositronYield_SweeperMagnet_run60-61} %\caption{Spectrum.} %\label{fig:2008-spectrum-zoom} %\end{figure}


\section{Proposed Beamline} \indent


I propose a measurement of the positron production efficiency using the HRRL. The HRRL can provide electron beams with energies between 3~MeV and 16~MeV, and a maximum repetition rate of 300~Hz. The HRRL beamline has recently been reconfigured to generate and collect positrons, see Fig.~\ref{fig:HRRL-e+-line} and Table~\ref{tab:hrrl}.

\begin{table}[hbt]

  \centering
  \caption{Operational Parameters of The HRRL Linac.}
  \begin{tabular}{lccc}
      \toprule
      Parameter     & Unit   & Value \\
      \midrule
       maximum electron beam energy $E$   &  MeV     &  16   \\
      \midrule
      electron beam peak current $I_{\textnormal{peak}}$ &  mA      &  80     \\
       \midrule
       macro-pulse repetition rate                   &   Hz       &  300  \\
       \midrule
       macro-pulse pulse length (FWHM)          &   ns       &  250    \\
       \midrule
       rms energy spread                                &  \%      &   4.23   \\
 \bottomrule

\end{tabular} \label{tab:hrrl} \end{table}

The new beamline was first designed by Dr. G. Stancari to use a quadrupole triplet system to collect positrons~\cite{stancari}. The design was further optimized by Dr. Y Kim. The final design of the beamline is shown in Fig.~\ref{fig:HRRL-e+-line}. The HRRL accelerator room is divided into two parts by an L-shaped cement wall. The accelerator cell houses the cavity and other elements needed to transport electrons to an experimental cell. The experimental cell is located in a room adjacent to the accelerator cell. The HRRL beamline was reconfigured into an achromat by moving the accelerator cavity to accommodate two dipoles and a system of quadrupole magnets optimized for collecting positrons.

In the new beamline, shown in Fig.~\ref{fig:HRRL-e+-line}, the electron beam exits the cavity and passes through a quadruple triplet that will focus the electron beam onto the positron target. Positrons produced from the positron target will be collected by the second quadruple triplet that will be optimized to collect positrons. The first dipole magnet bends the positrons/electrons, depending on the magnet polarity, by 45 degrees towards the second dipole magnet. The second dipole will bend the beam another 45 degrees, thus completing a 90 degree bend. A third quadruple triplet will focus the e-/e+ beam, as users desire. All beam elements are described in Table~\ref{tab:new-hrrl-line-elements}.


%\begin{figure*}[htbp] \begin{sidewaysfigure*}[htbp]

\centering %\includegraphics[scale=0.28]{HRRL_Pos_and_Ele_Go} \includegraphics[scale=0.35]{HRRL_Pos_and_Ele_Go.eps} \caption{The new HRRL beamline cofiguration for positron generation.} \label{fig:HRRL-e+-line} \end{sidewaysfigure*}

%\end{figure*}


\begin{table}[hbt]

  \centering
  \caption{The new HRRL positron beamline elements.}
  \begin{tabular}{lccc}
      \toprule
        Item   &  Description \\
      \midrule
        T1    & Positron target \\
      \midrule
        T2    &  Annihilation target \\
       \midrule
        EnS    & Energy Slit  \\
       \midrule
        FC1, FC2& Faraday Cups \\
       \midrule
        Q1,...Q10	     & Quadrupoles \\
       \midrule
         D1, D2	    & Dipoles \\
       \midrule
        NaI     &  NaI Detecotrs \\
       \midrule
        OTR     &  Optical Transition Radiaiton screen\\
       \midrule
        YAG    & Yttrium Aluminium Garnet screen\\
 \bottomrule

\end{tabular} \label{tab:new-hrrl-line-elements} \end{table}

%00000000000000000000000000000000000000000000000000000000000 \section{Preparation for the Positron \\ Production Experiment} \subsection{HRRL Emittance measurements} \indent


Emittance, a key parameter in accelerator physics, is used to quantify the quality of an electron beam produced by an accelerator. The beam size and divergence at any point in the beamline can be described using emittance and Twiss parameters.

An Optical Transition Radiation (OTR) based viewer was installed to allow measurements at the high electron currents available from the HRRL. The visible light from the OTR based viewer is produced when a relativistic electron beam crosses the boundary of two mediums with different dielectric constants. Visible radiation is emitted at an angle of 90${^\circ}$ with respect to the incident beam direction~\cite{OTR} when the electron beam intersects the OTR target at a 45${^\circ}$ angle. These emitted photons are observed using a digital camera and can be used to measure the shape and intensity of the electron beam based on the OTR distribution.

The emittance of the HRRL was measured to be less than 0.4~$\mu$m using the OTR based tool at an energy of 15~MeV. The details of this emittance measurement using the quadrupole scanning method were described in the IPAC12 proceedings~\cite{setiniyaz-q-scan}. The results are summarized in Table~\ref{results}.

\begin{table}[hbt]

  \centering
  \caption{Emittance Measurement Results.}
  \begin{tabular}{lcc}
      \toprule
       {Parameter}         & {Unit}     &    {Value}    \\
      \midrule
        projected emittance $\epsilon_x$        &   $\mu$m    &    $0.37 \pm 0.02$     \\
         projected emittance $\epsilon_y$            &   $\mu$m    &    $0.30 \pm 0.04$     \\

% normalized \footnote{normalization procedure assumes appropriate beam chromaticity.} emittance $\epsilon_{n,x}$ & $\mu$m & $10.10 \pm 0.51$ \\ %normalized emittance $\epsilon_{n,y}$ & $\mu$m & $8.06 \pm 1.1$ \\

        $\beta_x$-function                            &  m                           &   $1.40  \pm  0.06$          \\
        $\beta_y$-function                                &  m                           &   $1.17   \pm 0.13$         \\

$\alpha_x$-function & rad & $0.97 \pm 0.06$ \\ $\alpha_y$-function & rad & $0.24 \pm 0.07$ \\ micro-pulse charge & pC & 11 \\ micro-pulse length & ps & 35 \\ energy of the beam $E$ & MeV & 15 $\pm$ 1.6 \\ relative energy spread $\Delta E/E$ & \% & 10.4 \\

 \bottomrule
  \end{tabular}
  \label{results}

\end{table}

\subsection{Positron Detection using NaI crystals} \indent

A tungsten target will be placed at the end of the 90 degree beamline to annihilate positrons. I want to use two NaI detectors to detect the 511~keV photons created when positrons annihilate. I acquired some NaI crystals from Idaho Accelerator Center (IAC). Since their original bases used a slow post-amplifier, I built new PMT bases. I modified the design of model PA-14 from Saint-Gobain Crystals \& Detectors Ltd. These detectors are tested, calibrated, and ready to be used for the measurement. Fig.~\ref{fig:IAC-dets} shows the crystals and the bases I built. Fig.~\ref{fig:IAC-dets-Co60-Na22-spec} shows the spectrum taken by the detector using button sources. %I expect by doing coincidence, the resolution of 511~keV peak in the spectrum will be improved.

\begin{figure}[htbp] \centering \includegraphics[scale=0.08]{IAC_NaI_Detectors} \caption{The NaI detector and base built.} \label{fig:IAC-dets} \end{figure}

\begin{figure}[htbp] \centering \includegraphics[scale=0.18]{Na22_Co60Spectrum_by_IAC_Detectors} \caption{Detector 3 calibrated Spectrum.} \label{fig:IAC-dets-Co60-Na22-spec} \end{figure}

%\subsection{Positron Target Installation} %\indent % %A step motor is ready to be installed once the vacuum chamber is ready. The step motor, shown in the Fig.~\ref{fig:step-motor}, will hold 8 tungsten targets. % %\begin{figure}[htbp] %\centering %\includegraphics[scale=0.08]{setep_motor} %\caption{Step motor for holding W targets.} %\label{fig:step-motor} %\end{figure}

\section{Future Plan} \indent

We want to produce positrons using the HRRL beam line. We can improve positron collection efficiency by applying following methods:

1. By using a quadrupole triplet before tungsten a target, we will have control over the beam size and divergence at the target.

2. Cryogenically cooled converter will be installed, and these targets will be able to take on more beam power and increase positron yield.

3. Positrons will be collected by the quadrupole triplet system, which will improve collection efficiency.

4. Simulations will optimize beam elements for positron collection.

%\bibliographystyle{unsrt} % Order by citation %\bibliography{report}

\begin{thebibliography}{9} %{stancari} %@techreport{stancari, % title =Template:Stancari's proposal-------, % month ={Nov.}, % year = {2005}, % author ={J. Stancari}, % address ={Frascati, Italy}, % number ={}, % institution ={DAFNE Technical Note} \bibitem{stancari}

G. Stancari and T. Forest "Design of a new beamline for electrons, positrons and photons at the HRRL lab", Pocatello, ID, USA (2009).


%@techreport{OTR, % title =Template:Optical Transition Radiation, % month ={}, % year = {1992}, % author ={B. Gitter}, % address ={Los Angeles, CA 90024}, % institution ={Particle Beam Physics Lab, Center for Advanced Accelerators, UCLA Department of Physics} %}

\bibitem{OTR} B. Gitter, Tech. Rep., Los Angeles, USA (1992).

%\bibitem{setiniyaz-q-scan} %@InProceedings{setiniyaz-q-scan, % author = {S. Setiniyaz, K. Chouffani, T. Forest, and Y. Kim}, % title = {TRANSVERSE BEAM EMITTANCE MEASUREMENTS OF A 16 MeV LINAC AT THE IDAHO ACCELERATOR CENTER}, % booktitle = {IPAC2012},%pages = {151--158}, % year = 2012, % address = {New Orleans, USA} %} \bibitem{setiniyaz-q-scan} S. Setiniyaz, K. Chouffani, T. Forest, and Y. Kim, in $Proc$. $IPAC2012$, New Orleans, USA.

%\bibitem{emit-mat} %C.F. Eckman $et$ $al$., in $Proc$. $IPAC2012$, New Orleans, USA.


\end{thebibliography}

\end{document}