|
|
| (2 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| ==Setting up Mathematica for DC Theta-Phi Isotropic Cone==
| |
|
| |
|
|
| |
| We can define the constraints of the plane the DC is in
| |
|
| |
| <pre>
| |
| right = ContourPlot[
| |
| x2 == Cot[29.5 \[Degree]] y + .09156, {y, -1, 1}, {x2, 0, 1.8},
| |
| Frame -> {True, True, False, False},
| |
| PlotLabel -> "Right side limit of DC as a function of X and Y",
| |
| FrameLabel -> {"y (meters)", "x (meters)"}, ContourStyle -> Black,
| |
| PlotLegends -> Automatic];
| |
|
| |
| left = ContourPlot[
| |
| x2 == -Cot[29.5 \[Degree]] y + .09156, {y, -1, 1}, {x2, 0, 1.8},
| |
| Frame -> {True, True, False, False},
| |
| PlotLabel -> "Right side limit of DC as a function of X and Y",
| |
| FrameLabel -> {"y (meters)", "x (meters)"}, ContourStyle -> Black,
| |
| PlotLegends -> Automatic];
| |
|
| |
| </pre>
| |
|
| |
|
| |
| We can define the x coordinate of the wires as they cross the midpoint plane as shown earlier.
| |
|
| |
| <pre>
| |
| x0forWires[number_] := .23168 + .01337*(number);
| |
| </pre>
| |
|
| |
|
| |
| We can define the point midway between two parallel lines as the point where one wire is recorded versus its next highest neighbor
| |
|
| |
| <pre>
| |
| x0forWireMiddles[
| |
| number_] := ((.23168 + .01337*(number)) + (.23168 + .01337*(number \
| |
| + 1)))/2;
| |
| </pre>
| |
|
| |
| All of the conditions dependent on <math> \theta </math>and <math>\phi</math>
| |
|
| |
| <pre>
| |
|
| |
| \[CapitalDelta]a :=
| |
| FullSimplify[(R Sin[\[Theta] \[Degree]])/
| |
| 2 (Csc[65 \[Degree] - \[Theta] \[Degree]] -
| |
| Csc[115 \[Degree] - \[Theta] \[Degree]]), \[Theta] > 0];
| |
| e := Sin[25 \[Degree]]/Cos[\[Theta] \[Degree]];
| |
| a := FullSimplify[(R Sin[\[Theta] \[Degree]])/
| |
| 2 (Csc[65 \[Degree] - \[Theta] \[Degree]] +
| |
| Csc[115 \[Degree] - \[Theta] \[Degree]]), \[Theta] > 0];
| |
| rD1 := Simplify[(a e - \[CapitalDelta]a) Tan[
| |
| 65 \[Degree]] Cos[\[Theta] \[Degree]], \[Theta] > 0];
| |
| rD2 := Simplify[(a e + \[CapitalDelta]a) Tan[
| |
| 65 \[Degree]] Cos[\[Theta] \[Degree]], \[Theta] > 0];
| |
| xD1 := Simplify[rD1 Cos[\[Phi] \[Degree]]];
| |
| yD1 := Simplify[rD1 Sin[\[Phi] \[Degree]]];
| |
| zD1 := Simplify[rD1 Cot[\[Theta] \[Degree]], \[Theta] > 0];
| |
| xD2 := Simplify[rD2 Cos[\[Phi] \[Degree]], \[Theta] > 0];
| |
| yD2 := Simplify[rD2 Sin[\[Phi] \[Degree]], \[Theta] > 0];
| |
| zD2 := Simplify[rD2 Cot[\[Theta] \[Degree]], \[Theta] > 0];
| |
| xP := Simplify[(R Cos[\[Phi] \[Degree]])/(Cot[\[Theta] \[Degree]] +
| |
| Cos[\[Phi] \[Degree]] Cot[65 \[Degree]]), \[Theta] > 0];
| |
| yP := Simplify[(R Sin[\[Phi] \[Degree]])/(Cot[\[Theta] \[Degree]] +
| |
| Cos[\[Phi] \[Degree]] Cot[65 \[Degree]]), \[Theta] > 0];
| |
| zP := Simplify[(R Cot[\[Theta] \[Degree]])/(Cot[\[Theta] \[Degree]] +
| |
| Cos[\[Phi] \[Degree]] Cot[65 \[Degree]]), \[Theta] > 0];
| |
| x1 := Simplify[(rD2^2 - rD1^2 +
| |
| Cot[\[Theta] \[Degree]]^2 (rD2^2 - rD1^2) - 2 xP (xD2 - xD1) -
| |
| 2 yP (yD2 - yD1) - 2 zP (zD2 - zD1))/(4 a e) - a e, \[Theta] >
| |
| 0];
| |
| x := Simplify[x1 - \[CapitalDelta]a + a e, \[Theta] > 0];
| |
| xCenter := x + \[CapitalDelta]a;
| |
| n := -957.412/(Tan[\[Theta] \[Degree]] + 2.14437) + 430.626;
| |
| D2P := Simplify[((xD2 - xP)^2 + (yD2 - yP)^2 + (zD2 -
| |
| zP )^2)^.5, \[Theta] > 0] // N
| |
| D1P := Simplify[((xP - xD1)^2 + (yP - yD1)^2 + (zP -
| |
| zD1)^2)^.5, \[Theta] > 0] // N;
| |
| y := Simplify[(D1P^2 - x1^2)^.5, \[Theta] > 0] // N;
| |
| b := Simplify[a Sqrt[1 - e^2], \[Theta] > 0] // N;
| |
| R = 2.52934271645;
| |
| </pre>
| |
|
| |
| We can define the x-y position on the DC plane as a function of \[Phi] for and limit the angles with the wall on the right and left hand sides. By symmetry these angles are equal, but opposite in sign. The range of <math>\phi</math> in the plane of the DC sector changes as <math>\theta</math> increases, so does <math>\phi</math> increase.
| |
|
| |
| <pre>
| |
| Limits = Table[\[Phi] /.
| |
| NSolve[Sqrt[a^2 (1 - y^2/b^2)] - \[CapitalDelta]a ==
| |
| Cot[29.5 \[Degree]] y + .09156 , \[Phi]], {\[Theta], 5, 40}];
| |
| Lim = Table[0, {rows, 1, 36}];
| |
| For[rows = 1, rows < 37, rows++,
| |
| For[i = 1, i < 5, i++,
| |
| If[Limits[[rows, i]] > 0 && Limits[[rows, i]] < 40,
| |
| Lim[[rows]] = Limits[[rows, i]];
| |
| ];
| |
| ];
| |
| ];
| |
| </pre>
| |
|
| |
| The angle must have 4 subtracted to equal the line element numbering
| |
|
| |
| <pre>
| |
| In[33]:= Lim[[7 - 4]]
| |
|
| |
| Out[33]= 23.4101
| |
| </pre>
| |
|
| |
| The limit of <math>\phi</math> increases in the plane of the DC sector changes as <math>\theta</math> increases.
| |
|
| |
| <pre>
| |
| In[34]:= Lim[1]
| |
|
| |
| Out[34]= {20.076, 22.024, 23.4101, 24.448, 25.255, 25.9008, 26.4297,
| |
| 26.8711, 27.2453, 27.5667, 27.846, 28.0911, 28.3079, 28.5013,
| |
| 28.675, 28.8319, 28.9744, 29.1044, 29.2237, 29.3336, 29.4352,
| |
| 29.5294, 29.6171, 29.699, 29.7757, 29.8477, 29.9155, 29.9795,
| |
| 30.0399, 30.0973, 30.1517, 30.2034, 30.2528, 30.2999, 30.3449,
| |
| 30.388}[1]
| |
| </pre>
| |
|
| |
| This limiting condition will record the angle <math>\phi</math> in degrees within an array of wire number(1-112) horizontally and angle <math>\theta (5\circ-40\circ )</math> vertically
| |
|
| |
| <pre>
| |
| RightSolutions =
| |
| Table[{\[Phi] /.
| |
| Solve[Sqrt[a^2 (1 - y^2/b^2)] - \[CapitalDelta]a ==
| |
| Tan[6 \[Degree]] y +
| |
| x0forWireMiddles[number] , \[Phi]]}, {\[Theta], 5,
| |
| 40}, {number, 1, 112}];
| |
| LineRight = Table[{\[Phi], columns}, {rows, 1, 36}, {columns, 1, 112}];
| |
| For[rows = 1, rows < 37, rows++,
| |
| For[columns = 1, columns < 113, columns++,
| |
| For[i = 1, i < 5, i++,
| |
| If[RightSolutions[[rows, columns, 1, i]] > 0 &&
| |
| RightSolutions[[rows, columns, 1, i]] < Lim[[rows]],
| |
| LineRight[[rows,
| |
| columns]] = {RightSolutions[[rows, columns, 1, i]],
| |
| columns + .5};
| |
| ];
| |
| ];
| |
| ];
| |
| ];
| |
| </pre>
| |
|
| |
| At \[Phi]=0, the condition of n=-959.637/(tan \[Theta]\[Degree] +2.14437)+430.189 should be met
| |
|
| |
| <pre>
| |
| In[38]:= f[\[Theta]for\[Phi]at0_] := -959.637/(
| |
| Tan[\[Theta]for\[Phi]at0 \[Degree]] + 2.14437) + 430.189
| |
|
| |
| In[39]:= f[40]
| |
|
| |
| Out[39]= 108.538
| |
| </pre>
| |
|
| |
|
| |
| This implies that for \[Theta]=40, we know that the wire number to be 108.538. This corresponds to the position being in between 108.5 and 109.5, hence it falls into the 109 "bin".
| |
|
| |
| Testing the geometry
| |
| <pre>
| |
| ClearAll[\[Theta]];
| |
| \[Theta] = 40;
| |
| ellipse40 =
| |
| ContourPlot[(x + \[CapitalDelta]a)^2/a^2 + y^2/b^2 == 1, {y, -1,
| |
| 1}, {x, 1.2, 1.7}, Frame -> {True, True, False, False},
| |
| PlotLabel ->
| |
| "XY position on DC as a function of \[Phi] for \[Theta]=40\
| |
| \[Degree]", FrameLabel -> {"y (meters)", "x (meters)"},
| |
| ContourStyle -> Red, PlotLegends -> Automatic];
| |
| Show[Table[
| |
| ContourPlot[
| |
| xWire == Tan[6 \[Degree]] yWire + x0forWires[number], {yWire, -1,
| |
| 1}, {xWire, 1.2, 1.7},
| |
| FrameLabel -> {"y(meters)", "x(meters)"}], {number, 70, 109}],
| |
| Table[ContourPlot[
| |
| xWire ==
| |
| Tan[6 \[Degree]] yWire + x0forWireMiddles[number2], {yWire, -1,
| |
| 1}, {xWire, 1.2, 1.7},
| |
| ContourStyle -> {Dashing[Large]}], {number2, 70,
| |
| 109}], bottom, right, left, ellipse40]
| |
| </pre>
| |
|
| |
| [[File:40EllipseTest.png]]
| |