Difference between revisions of "Calculating the differential cross-sections for the different materials, and placing them as well as the theoretical differential cross-section into a plot:"
(43 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | <center>[[File:Moller_Theta_CM_3materials.png|frame|left||'''Figure 8d:''' The Moller scattering angle theta for 4E7 incident 11 GeV electrons in the Center of Mass frame of reference for 3 different target materials.]] | ||
+ | {| border=1 | ||
+ | |+ '''Density of target material''' | ||
+ | |- | ||
+ | ! Material | ||
+ | ! Density (g/cm<sup>3</sup>) | ||
+ | |- | ||
+ | | C | ||
+ | | 2.26 | ||
+ | |- | ||
+ | | NH3 | ||
+ | | 0.86 | ||
+ | |- | ||
+ | | LH2 | ||
+ | | 0.07 | ||
+ | |} | ||
+ | </center> | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
Comparing this to the theoretical differential cross section | Comparing this to the theoretical differential cross section | ||
− | [[DV_RunGroupC_Moller#Comparing_experimental_vs._theoretical_for_M.C3.B8ller_differential_cross_section_11GeV |As shown | + | [[DV_RunGroupC_Moller#Comparing_experimental_vs._theoretical_for_M.C3.B8ller_differential_cross_section_11GeV |As shown earlier ]], we find that the differential cross section scale is <math>\frac{d\sigma}{d\Omega}\approx 16.2\times 10^{-2}mb=16.2\mu b</math> |
Line 51: | Line 90: | ||
Theory->Draw("same");</pre> | Theory->Draw("same");</pre> | ||
− | [[File:Combo4.png|frame| | + | |
+ | <center>[[File:Combo4.png|frame|left||'''Figure 8c:''' The Moller electron differential cross-section for 4E7 incident 11 GeV electrons in the Center of Mass frame of reference.]] | ||
+ | {| border=1 | ||
+ | |+ '''Molar Mass of Target Material''' | ||
+ | |- | ||
+ | ! Material | ||
+ | ! Molar Mass (g/mole) | ||
+ | |- | ||
+ | | NH3 | ||
+ | | 17 | ||
+ | |- | ||
+ | | C | ||
+ | | 12 | ||
+ | |- | ||
+ | | LH2 | ||
+ | | 2 | ||
+ | |} | ||
+ | |||
+ | |||
+ | {| border=1 | ||
+ | |+ '''Number of Electrons in Target Material''' | ||
+ | |- | ||
+ | ! Material | ||
+ | ! Number of Electrons | ||
+ | |- | ||
+ | | NH3 | ||
+ | | 10 | ||
+ | |- | ||
+ | | C | ||
+ | | 6 | ||
+ | |- | ||
+ | | LH2 | ||
+ | | 2 | ||
+ | |} | ||
+ | |||
+ | </center> | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | <math>\Longrightarrow</math>''The molar mass is proportional to the number of electrons in the target material. The theoretical Moller differential cross-section is an expression for a single scattering electron. NH3, as a molecule, is composed of 10 electrons that all have an equal momentum and probability of scattering with the incident electron in the CM frame.'' | ||
+ | |||
+ | |||
+ | |||
+ | Comparing this with a plot of the Moller scattering angle theta, | ||
+ | |||
+ | |||
+ | |||
+ | <center>[[File:3targets.png|frame|left|alt=Moller Electron Momentum in Lab Frame|'''Figure 8b:''' The Moller electron momentum distribution for 4E7 incident 11 GeV electrons in the Lab frame of reference.]] | ||
+ | {| border=1 | ||
+ | |+ '''Density of target material''' | ||
+ | |- | ||
+ | ! Material | ||
+ | ! Density (g/cm<sup>3</sup>) | ||
+ | |- | ||
+ | | C | ||
+ | | 2.26 | ||
+ | |- | ||
+ | | NH3 | ||
+ | | 0.86 | ||
+ | |- | ||
+ | | LH2 | ||
+ | | 0.07 | ||
+ | |} | ||
+ | </center> | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | <math>\Longrightarrow</math>''In the lab frame, the incident electron, and the transfer of its momentum, depends on the stationary target material density. The more dense material requires more energy to break free an electron from the target material. This higher energy results in a smaller maximum scattering angle theta for the Moller electron in the Lab frame.'' | ||
+ | |||
+ | Adjusting the theoretical differential cross-section for 10 times less, | ||
+ | <pre> | ||
+ | TH1F *Combo=new TH1F("TheoryExperiment","Theoretical and Experimental Differential Cross-Section CM Frame",360,90,180); | ||
+ | TH1F *Combo2=new TH1F("TheoryExperiment2","Theoretical and Experimental Differential Cross-Section CM Frame",360,90,180); | ||
+ | Combo->Add(MollerThetaCM,8.87e-7); | ||
+ | Combo2->Add(Theory,1e-1); | ||
+ | Combo2->Draw(); | ||
+ | Combo->Draw("same"); | ||
+ | </pre> | ||
+ | |||
+ | <center>[[File:Adjusted_MollerXSect_NH3.png]]</center> | ||
+ | |||
+ | |||
+ | |||
---- | ---- | ||
+ | |||
=Links= | =Links= | ||
− | [[DV_RunGroupC_Moller|Back]] | + | [[DV_RunGroupC_Moller#Differential_Cross-Section_Offset|Back]] |
Latest revision as of 17:59, 15 April 2016
Material | Density (g/cm3) |
---|---|
C | 2.26 |
NH3 | 0.86 |
LH2 | 0.07 |
Comparing this to the theoretical differential cross section
As shown earlier , we find that the differential cross section scale is
Converting the number of electrons to barns,
where ρtarget is the density of the target material, ltarget is the length of the target, and iscattered is the number of incident particles scattered.
For LH2:
For Carbon:
For Ammonia:
Combing plots in Root:
new TBrowser(); TH1F *LH2=new TH1F("LH2","LH2",360,90,180); LH2->Add(MollerThetaCM,1.19e-6); LH2->Draw(); TH1F *C12=new TH1F("C12","C12",360,90,180); C12->Add(MollerThetaCM,2.21e-7); C12->Draw(); TH1F *NH3=new TH1F("NH3","NH3",360,90,180); NH3->Add(MollerThetaCM,8.87e-7); NH3->Draw(); LH2->Draw("same"); C12->Draw("same"); Theory->Draw("same");
Material | Molar Mass (g/mole) |
---|---|
NH3 | 17 |
C | 12 |
LH2 | 2 |
Material | Number of Electrons |
---|---|
NH3 | 10 |
C | 6 |
LH2 | 2 |
The molar mass is proportional to the number of electrons in the target material. The theoretical Moller differential cross-section is an expression for a single scattering electron. NH3, as a molecule, is composed of 10 electrons that all have an equal momentum and probability of scattering with the incident electron in the CM frame.
Comparing this with a plot of the Moller scattering angle theta,
Material | Density (g/cm3) |
---|---|
C | 2.26 |
NH3 | 0.86 |
LH2 | 0.07 |
In the lab frame, the incident electron, and the transfer of its momentum, depends on the stationary target material density. The more dense material requires more energy to break free an electron from the target material. This higher energy results in a smaller maximum scattering angle theta for the Moller electron in the Lab frame.
Adjusting the theoretical differential cross-section for 10 times less,
TH1F *Combo=new TH1F("TheoryExperiment","Theoretical and Experimental Differential Cross-Section CM Frame",360,90,180); TH1F *Combo2=new TH1F("TheoryExperiment2","Theoretical and Experimental Differential Cross-Section CM Frame",360,90,180); Combo->Add(MollerThetaCM,8.87e-7); Combo2->Add(Theory,1e-1); Combo2->Draw(); Combo->Draw("same");
![Adjusted MollerXSect NH3.png](/./images/d/d6/Adjusted_MollerXSect_NH3.png)