Difference between revisions of "IAC-QDC Measurements"
Jump to navigation
Jump to search
| Line 36: | Line 36: | ||
=10/04/13= | =10/04/13= | ||
| − | Measurement settings, amp. 1x 50 ns differentiation, discriminator 100 mV, so the signal is 100 mV and noise is 30 mV. | + | Measurement settings, amp. 1x 50 ns differentiation, discriminator's threshold is 100 mV, so the signal is 100 mV and noise is 30 mV. |
| − | discriminator is lowered to 73 mV to the measure the noise charge on the ADC. | + | discriminator's threshold is lowered to 73 mV to the measure the noise charge on the ADC. |
| Line 47: | Line 47: | ||
|- | |- | ||
|6226 || 16:34:09 || 16:46:44 || shutter close V_GEM= V_cat [[File:6226_adc_sh_open.png | 100 px]] | |6226 || 16:34:09 || 16:46:44 || shutter close V_GEM= V_cat [[File:6226_adc_sh_open.png | 100 px]] | ||
| + | |- | ||
| + | |6227 || 16:52:39 || 16:46:44 || shutter open V_GEM= V_cat discriminator's threshold decreased to 57 mV [[File:6227_adc_sh_open.png | 100 px]] | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |} | ||
Revision as of 22:54, 4 October 2013
09/18/13
Detector voltage is 2.8, 3.4 kV for cathode and GEM. filter Amp. (x4 level 6) is used for amplify the GEM's output, ch#5 is used as an ADC input and ch# 31 in TDC
| Run Number | Start time | End time | Notes | |
| 6075 | 12:39:16 | 13:19:33 | shutter open |  
|
| 6077 | 13:34 :37 | 14:19:05 | shutter close, pmt is connected to ch#11 qdc and ch#27 tdc |   
|
10/03/13
Detector voltage is 2.8, 3.4 kV for cathode and GEM. filter Amp. (x2 level 6) is used for amplify the GEM's output, ch#5 is used as an ADC input.
| Run Number | Start time | End time | Notes |
| 6220 | 17:34:47 | 17:55:48 | shutter close N = 0.000793021 
|
| 6221 | 17:57:08 | 18:03:52 | shutter close V_GEM= V_cat but still there are two peaks. N= 0.002475248 
|
| 6222 | 18:20:48 | 18:21:04 | shutter open V_GEM= V_cat but still there are two peaks.high noise rate 14 kHz 
|
10/04/13
Measurement settings, amp. 1x 50 ns differentiation, discriminator's threshold is 100 mV, so the signal is 100 mV and noise is 30 mV.
discriminator's threshold is lowered to 73 mV to the measure the noise charge on the ADC.
| Run Number | Start time | End time | Notes |
| 6226 | 16:34:09 | 16:46:44 | shutter close V_GEM= V_cat 100 px |
| 6227 | 16:52:39 | 16:46:44 | shutter open V_GEM= V_cat discriminator's threshold decreased to 57 mV 100 px
|
