CH PAS Master Timeline

Timeline

This page will be used to document when each task is started/completed as a master reference for all work accomplished. The plan is to make my life easier when I have to look through months of work.

May

5/10/21

• Attended intern orientation for first day at INL

• Completed training this week as well as began NaI plateau setup

5/11/21

• Put first coat of paint onto lead bricks to be used as shielding in PAS experiment

5/12/21

• Moved steel table from LDS to clean room and began set up

5/17/21

• Sheared a lead sheet into 6 rough 3"x3" squares to be used for attenuation measurements with NaI detectors

• Lead sheet pieces were wiped down with a wet wipe, duct taped, rewiped, and hammered flat.

5/18/21

• Began data collection for NaI plateau and operating point measurements

• Began writing analysis code for NaI plateau measurements

5/27/21

• Finished painting lead bricks and left to cure

Unknown time when tasks were completed

• Gathered borated poly with Paul

• Tested NaI detectors and found one working base

June

6/1/21

• Moved dried/cured painted lead bricks from painting area to clean room

• Cleaned each brick with a wet wipe before transition into clean room, will be allowed to air dry on steel table

• • 50 bricks total: 49 half bricks and 1 full brick

• Steel table set up finished

6/4/21

• Created initial lead brick tunnel

6/8/21

• Finished collection and analysis of NaI detector plateau measurements, voltages ranging from 700V to 1400V

• • Analysis included Souce in & Source out plots, Signal:Noise, and background subtracted plots

6/9/21

• Began data colleciton for He3 Borated Poly attenuation study

6/11/21

• Finished data collection for He3 Borated Poly attenuation study

• Began writing analysis code for Borated Poly attenuation study

6/21/21

• Spent the day at INL with Chuting and Paul

6/22/21

• Finished writing analysis code for He3 Borated Poly attenuation measurements and submitted plot to Paul

• Began designing cradle for NaI detector using fusion360

6/24/21

• Finished modeling cradle and sent designs to Jeff Burggraf who offered to print it for me

6/25/21

• Began BorAl attenuation measurements including overnight background runs

6/26/21

• First BorAl background run lasted 60000 seconds and ended at approximately 11:45am 6/26/21

• Continuing to run Borated Poly attenuation measurements with BorAl surrounding He3 tube

• Cradle for NaI detector has been printed and should be in lab Tuesday 6/29/21

• Created github repository to advertise my poor coding practices

• Began mapping shielding measurements for Lead, BorAl, and various Poly

6/28/21

• Continued BorAl/Borated Poly attenuation measurements with He3 tube

• Began working with MCNP

• Continued to map out BorAl placement and shielding design for feasibility study
  • We need more BorAl

6/29/21

• Finished BorAl/Borated Poly attenuation measurements

• Got signal from HPGe detector

• Discussed various poly box and shielding arrangements for feasibility study
  • Designs need to be drawn up
  • Lead tunnel needs to be made bigger to accommodate HPGe detector
    • Will probably need to model another cradle for HPGe
  • Need to source more regular poly and cut it to appropriate length and widths

6/30/21

• Sourced regular poly and lead sheets, will be washed and brought to clean room today

• Finalized design of poly box for feasibility study
  • Will have to cut some poly blocks to fit the needed dimensions

• Finished designing poly brick thermalizing box and lead shielding

• Brought poly down to LDS in dark room to be washed

• Tony and Paul were able to get a good signal out of HPGe detector

Unknown time when tasks were completed

• Found a fifth NaI detector (no base) with smaller crystal diameter (5.5cm)

• Helped Tony and Joe moved DD generator from nuke eng department and subsequently lift into clean room

• Moved HPGe detector into clean room and unpacked it, Paul has begun preliminary functionality testing

July

7/1/21

• Installed cradle into lead tunnel

• Discussed solid state physics with Dr. Forest regarding HPGe detector

• Tested various arrangements to show that BorAl is most effective after borated poly and not before down beam axis

• Received new daq from CoSE IT and Dr. Forest did preliminary setup

7/2/21

• Finished and posted BorAl/BPoly/Poly attenuation measurement study

• Redesigned thermalizing box with Paul

• Created and posted BorAl shielded He3 attenuation measurements plot

• Made and posted BorAl/Poly/Bpoly attenuation measurements plot

7/5/21

• Fourth of July (observed)

7/6/21

• Met with CoSE IT about DAQ issues
  • Need to upgrade DAQ to at least CENT OS 7, 8 may be better. Currently running version 6 which is too old for security updates

• Worked with Paul on experimental setup design and marked some BorAl for cutting back at INL

• Modeled experimental setup in fusion 360
  • Need more data from mcnp to finalize shielding designs

7/7/21

• Washed regular poly for use in thermalizing cavity in experimental setup

• Received new ADC and Gadolinium sheet from Chuting

• Worked on MCNP and thermalizing box design with Paul

• Gave some BorAl back to chuting to be cut

7/9/21

• Downloaded new MCNP libraries to run Paul's new script

• Spoke to Joe (chemist) about separating boron from BorAl and BPoly

• Started working through python lessons

• Started photon attenuation measurements in lead tunnel

7/12/21

• Updated 3D model of feasibility study with Gadolinium converter and smoothed out some edges that were improperly situated

Future tasks not on meeting task list

• Draw cuts on BorAl pieces and find out how much more will be needed

• Need to talk to CoSE IT to get new DAQ computer and find out how to link into HPGe detector through switch in clean room

• Have CoSE IT mount second disk in new daq called (data) and give access to second partition on first disk

• Have CoSE IT swap MAC addresses for two daqs and give network access to hpge through browser and switch

• New daq cannot find a valid base url for repo: base

Go Back

---

CH_Task_List

PAS_Experiment