Difference between revisions of "Reproducibility Shots July 2017"
| (26 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | '''Shot | + | <div style="text-align: center;"> |
| + | ='''Shot 169'''= | ||
In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV. | In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV. | ||
| Line 5: | Line 6: | ||
I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator. | I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator. | ||
| − | + | Diode diameter: 2" | |
| + | Diode gap: 1.5" | ||
| + | Al vacuum plate thickness: 5/8" | ||
| + | Ta thickness: 0.020" | ||
| + | Distance to Board: 109 cm | ||
| + | Calculated amount of charge: -2.106e07 C </div> | ||
| + | [[File:Shot 1 Front Jul2017.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | [[File:Shot 1 Back Jul2017.png|400px|thumb|center|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot_1_Front_Back_X_Overlay.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot_1_Front_Back_Y_Overlay.png|450px|thumb|center|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot169%Diff.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot169_Current.png|400px|thumb|center|]] | ||
| + | |||
| + | |||
| + | <div style="text-align: center;"> | ||
| + | ='''Shot 170'''= | ||
| + | |||
| + | In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV. | ||
| + | |||
| + | I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator. | ||
| + | |||
| + | Diode diameter: 2" | ||
| + | |||
| + | gap: 2.5" | ||
| + | |||
| + | Al vacuum plate thickness: 1/8" | ||
| + | |||
| + | Ta thickness: 0.020" | ||
| + | |||
| + | Distance to Board: 102 cm | ||
| + | |||
| + | Calculated amount of charge: -1.679E07 | ||
| + | |||
| + | </div> | ||
| + | |||
| + | |||
| + | [[File:Shot170F.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot170B.png|400px|thumb|center|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot_170_Front_Back_X_Overlay.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot_170_Front_Back_Y_Overlay.png|400px|thumb|center|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot170%Diff.png|400px|thumb|left|*Unknown calibration on OSL reader]] | ||
| + | |||
| + | [[File:Shot170Current.png|400px|thumb|center|]] | ||
| + | |||
| + | |||
| + | <div style="text-align: center;"> | ||
| + | ='''Shot 179'''= | ||
| + | |||
| + | In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV. | ||
| + | |||
| + | I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator. | ||
| + | |||
| + | Diode diameter: 1" hemispherical | ||
| + | |||
| + | gap: 2.1" | ||
| + | |||
| + | Al vacuum plate thickness: 1/8" | ||
| + | |||
| + | Ta thickness: 0.020" | ||
| + | |||
| + | Distance to Board: 99 cm | ||
| + | |||
| + | Calculated amount of charge: -1.498E07 </div> | ||
| + | |||
| + | |||
| + | [[File:Shot179Current.png|400px|thumb|center|]] | ||
[[TriMeV Shot Log]] | [[TriMeV Shot Log]] | ||
Latest revision as of 21:40, 3 August 2017
Shot 169
In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV.
I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator.
Diode diameter: 2"
Diode gap: 1.5"
Al vacuum plate thickness: 5/8"
Ta thickness: 0.020"
Distance to Board: 109 cm
Calculated amount of charge: -2.106e07 C
Shot 170
In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV.
I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator.
Diode diameter: 2"
gap: 2.5"
Al vacuum plate thickness: 1/8"
Ta thickness: 0.020"
Distance to Board: 102 cm
Calculated amount of charge: -1.679E07
Shot 179
In this experiment, I picked 17 different points on my OSL board to test agreement between two OSLs at the same physical location for the same shot from TriMeV.
I have overlaid X and Y profiles as well as created 3D renderings of the beam profile for the front and back sets of OSLs. Note that it is flat due to the distance at which the board was placed from the end of the accelerator.
Diode diameter: 1" hemispherical
gap: 2.1"
Al vacuum plate thickness: 1/8"
Ta thickness: 0.020"
Distance to Board: 99 cm
Calculated amount of charge: -1.498E07
