Foretony: /* CAEN Keypad Function Codes */

2011-01-23T18:23:16Z

CAEN Keypad Function Codes

Foretony: /* CAEN Keypad Function Codes */

2011-01-23T18:17:04Z

CAEN Keypad Function Codes

Foretony: Created page with ' File:CAEN_N470_Manual.pdf =CAEN Keypad Function Codes= NOTE: The channel number to which all the commands and information on the displays and LEDs are referred is always…'

2011-01-23T18:13:59Z

Created page with ' File:CAEN_N470_Manual.pdf =CAEN Keypad Function Codes= NOTE: The channel number to which all the commands and information on the displays and LEDs are referred is always…'

New page

[[File:CAEN_N470_Manual.pdf]]

=CAEN Keypad Function Codes=

NOTE: The channel number to which all the commands and information on the displays and LEDs
are referred is always shown on the left hand side of the upper display .

The digitised data becomes active only after the "*" key has been hit. So, for example, to select the
channel 1, the "CHANNEL" function is first called by typing "F0*" (see table 1) followed by the
desired channel number 1 and confirmed pressing the "*" key.

{| border="3" cellpadding="20" cellspacing="0"
|NUMBER || MNEMONIC ||MESSAGE|| RANGE || MEANING
|-
|0 ||CH || Channel || 0 to 3 || Selects the channel
|-
|1 || V0 || V0-Set || 0 V to 8000 V|| Programs the first High Voltage value
|-
|2|| I0 || I0-Set|| 0 to 3000 µA || Programs the first Current Limit value
|-
|3|| I1 || I1-Set || 0 to 3000 µA || Programs the second Current Limit value
|-
|4 || TR || Trip || 0 to 9999|| Programs the Trip Time
|-
|5|| V1|| V1-Set|| 0 V to 8000 V || Programs the second High Voltage value
|-
|6 || VM || V mon || || Reads the H.V. Monitor
|-
|7 || IM || I mon || || Reads the Current Monitor value
|-
|8 || RU|| Ramp up|| 1 to 500 V/s || Programs the H.V. Increase rate
|-
|9 || RD || Ramp down || 1 to 500 V/s || Programs the H.V. Decrease rate
|-
|10 || ON || On || || Turns the channel ON
|-
|11 || OFF || Off || || Turns the channel OFF
|-
|12 || KILL || Kill || || All H.V. channels are switched off
|-
|13 || MAXV|| V-Max || || Reads the VMAX value
|-
|14 || CL ALARM || Cl Alarm || || Resets the status of the ALARM output signal
|-
|15|| LEV || Lev () || || Selects the standard TTL or NIM of the hardware monitor signals.
|-
|89 || Lumin. || Sel Lum || 1 to 7 || Adjusts the luminosity of the 2 displays (1 to 7)
|-
|90|| V Calib || V Calib || || Performs the calibration of the output voltage
|-
|91|| I Calib|| I Calib || || Performs the calibration of the output current
|-
|92|| MaxV Calib || MaxV Cal || Performs the calibration of the MAXV
|-
|99 || Cr. || Cr. Num. || 0 to 99 || Sets the CAENET address
|}

← Older revision		Revision as of 18:23, 23 January 2011
Line 56:		Line 56:
	\|99 \|\| Cr. \|\| Cr. Num. \|\| 0 to 99 \|\| Sets the CAENET address		\|99 \|\| Cr. \|\| Cr. Num. \|\| 0 to 99 \|\| Sets the CAENET address
	\|}		\|}
		+
		+
		+	[[Qweak]]

@@ Line 52: / Line 52: @@
 |91||  I Calib||  I Calib || ||  Performs the calibration of the output current
 |-
-|92||  MaxV Calib || MaxV Cal  || Performs the calibration of the MAXV
+|92||  MaxV Calib || MaxV Cal  || ||Performs the calibration of the MAXV
 |-
 |99 || Cr. || Cr. Num. || 0 to 99 || Sets the CAENET  address
 |}

Qweak CAEN HV - Revision history

Foretony: /* CAEN Keypad Function Codes */

Foretony: /* CAEN Keypad Function Codes */

Foretony: Created page with ' File:CAEN_N470_Manual.pdf =CAEN Keypad Function Codes= NOTE: The channel number to which all the commands and information on the displays and LEDs are referred is always…'