PAS Lead Tunnel - Revision history

Harpconn at 03:15, 5 June 2021

2021-06-05T03:15:36Z

2021-06-05T03:15:25Z

2021-06-05T03:11:03Z

2021-06-05T03:10:48Z

2021-06-05T03:10:00Z

2021-06-05T03:09:32Z

2021-06-05T03:08:43Z

2021-06-05T03:08:36Z

2021-06-05T03:08:21Z

2021-06-05T03:07:12Z

@@ Line 3: / Line 3: @@
 * Tunnel will need to be torn down and rebuilt as the entire exterior will need to have a layer of BorAl surrounding it. Once optimal operating point for NaI detector has been found, source in/out measurements will be made to determine signal:noise in tunnel. Will repeat the same experiment with the addition of BorAl.
-Internal measurements of rectangular tube 103mm x 152mm
+* Plan to model cradle for NaI detector to put crystal in the center of the tube. Crystal is 3in in diameter (yay units)
-Plan to model cradle for NaI detector to put crystal in the center of the tube. Crystal is 3in in diameter (yay units)
+* Hope to 3D print cradle out of ABS plastic, possible to have one machined out of aluminum too
 {| class="wikitable " border="2" style="text-align:center;" |cellpadding="20" cellspacing="1

← Older revision		Revision as of 03:15, 5 June 2021
Line 1:		Line 1:
	Made lead brick tube 6/4/2021		Made lead brick tube 6/4/2021
		+
		+	* Tunnel will need to be torn down and rebuilt as the entire exterior will need to have a layer of BorAl surrounding it. Once optimal operating point for NaI detector has been found, source in/out measurements will be made to determine signal:noise in tunnel. Will repeat the same experiment with the addition of BorAl.
		+

	Internal measurements of rectangular tube 103mm x 152mm		Internal measurements of rectangular tube 103mm x 152mm

@@ Line 5: / Line 5: @@
 Plan to model cradle for NaI detector to put crystal in the center of the tube. Crystal is 3in in diameter (yay units)
-Hope to 3D print cradle, possible to have one machined too
+Hope to 3D print cradle out of ABS plastic, possible to have one machined out of aluminum too
 {| class="wikitable " border="2" style="text-align:center;" |cellpadding="20" cellspacing="1

← Older revision		Revision as of 03:10, 5 June 2021
Line 6:		Line 6:

	Hope to 3D print cradle, possible to have one machined too		Hope to 3D print cradle, possible to have one machined too
−
−	~~[[File:\|300px\|thumb\|left\|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]]~~
−
−	~~[[File:\|300px\|thumb\|center\|Looking down the center of the lead tunnel. Detector will be mounted at the far end ]]~~
−
−

	{\| class="wikitable " border="2" style="text-align:center;" \|cellpadding="20" cellspacing="1		{\| class="wikitable " border="2" style="text-align:center;" \|cellpadding="20" cellspacing="1

@@ Line 15: / Line 15: @@
 {| class="wikitable " border="2" style="text-align:center;" |cellpadding="20" cellspacing="1
 |-
-| [[File:PAS_Lead_Tunnel_1.jpg|300px|thumb|left|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]] || [[File:PAS_Lead_Tunnel_2.jpg|300px|thumb|center|Looking down the center of the lead tunnel. Detector will be mounted at the far end ]]
+| [[File:PAS_Lead_Tunnel_1.jpg|200px|thumb|left|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]] || [[File:PAS_Lead_Tunnel_2.jpg|300px|thumb|center|Looking down the center of the lead tunnel. Detector will be mounted at the far end ]]
 |-
 |}

@@ Line 14: / Line 14: @@
 {| class="wikitable " border="2" style="text-align:center;" |cellpadding="20" cellspacing="1
 |-
 | [[File:|300px|thumb|left|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]] || [[File:|300px|thumb|center|Looking down the center of the lead tunnel. Detector will be mounted at the far end ]]

@@ Line 13: / Line 13: @@
-{| class="wikitable mw-collapsible mw-collapsed" border="2" style="text-align:center;" |cellpadding="20" cellspacing="1
+{| class="wikitable " border="2" style="text-align:center;" |cellpadding="20" cellspacing="1
 |-
 | '''700V Plots'''||

@@ Line 9: / Line 9: @@
 [[File:|300px|thumb|left|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]]
-[[File:|300px|thumb|center|Lead tunnel created on steel table in clean room. Detector will be mounted inside in a cradle ]]
+[[File:|300px|thumb|center|Looking down the center of the lead tunnel. Detector will be mounted at the far end ]]
 ----
 [[PAS_Experimental_Setup]]