Foretony: Created page with ' MVME 6100
ROC1 ethernet address: 0001AF1998B5
ROC1 ethernet address: 0001AF1998B6
MPC7457 RISC G4 processor (PPC family)
== Download files from JLAB == I down…'

2012-06-12T17:39:54Z

Created page with ' MVME 6100 ROC1 ethernet address: 0001AF1998B5 ROC1 ethernet address: 0001AF1998B6 MPC7457 RISC G4 processor (PPC family) == Download files from JLAB == I down…'

New page

MVME 6100 
ROC1 ethernet address: 0001AF1998B5 
ROC1 ethernet address: 0001AF1998B6 
MPC7457 RISC G4 processor (PPC family) 
== Download files from JLAB ==

I downloaded the boot file and VXworks kernel from JLAB

/site/coda/kern/5.5/boot/boot6100_122.bin
/site/coda/kern/5.5/vx6100_v4.1

and put in /tftpboot subdirectory on Host computer

==Debug Connector ==

I then used the serial port on the host computer to interface with the MVME6100 via the "DEBUG" port. The debug port took an RJ45 standard cable so I got and RJ45-DB9 converter. This seemed to work out of the box. Just in case I ever need to make my own connector record the pinouts below.

[http://www.slac.stanford.edu/grp/lcls/controls/global/standards/hardware/v6100a_ih.pdf Information below is Table 5-11 pg 92 of this reference]
{| border="1"
| ROC Pin# || DB9 Pin # || DB9 shell || Signal
|-
| 1 || 1 || Blue || DCD (Carrier Detect)
|-
| 2 || 7 || Orange || RTS (Request to Send)
|-
| 3 || 5 || Black || GNDC
|-
| 4 || 3 || Red || TX (Transmit)
|-
| 5 || 2 || Green || RX (Recieve)
|-
| 6 || 5 || Yellow || GNDC
|-
| 7 || 8 || Brown || CTS (Clear to Send)
|-
| 8 || 4 || White || DTR (Data Terminal Ready)
|}

== MVME6100 BOOT screen==
===Minicom===

You can use "minicom -s" to set the default parameter to communication

I found the ROC was connected to /dev/ttyS1

I used "minicom" on the host computer to talk to the ROC. You have to be super user in order to run minicom unless you change the default permissions. The speed should be 9600 baud which you set using the keyboard sequence "Ctrl-A Z P E".

<pre>
Copyright Motorola Inc. 1999-2007, All Rights Reserved
MOTLoad RTOS Version 2.0, PAL Version 2.1 RM02
Wed Feb 7 11:32:02 MST 2007

MPU-Type =MPC74x7
MPU-Int Clock Speed =1266MHz
MPU-Ext Clock Speed =133MHz
MPU-Int Cache(L2) Enabled, 512KB, L2CR =C0000000
MPU-Ext Cache(L3) Enabled, 2MB, 211MHz, L3CR =DC026000

PCI bus instance 0 =64 bit, 133 Mhz, PCI-X
PCI bus instance 1 =64 bit, PCI

Reset/Boot Vector =Flash1

Local Memory Found =20000000 (&536870912)
User Download Buffer =006B7000:008B6FFF
</pre>

== Basic commands==

=== setting the time===

The command below will print the help screen for the time set command

he set

for example

MVME6100> set -t082604163100

08 = Month 
26 = day 
04 = year 
16 = hour (24 hour clock) 
31 = min 
00 = seconds 

MVME6100> time

THU AUG 26 16:31:02.00 2004

=== Ping another computer to check network===

I was unable to ping unless I used the "LAN1" RJ45 etherenet port

MVME6100> ping -c134.50.3.216 -s134.50.3.210
Client (Source) IP Address = 134.50.3.216
Server (Destination) IP Address = 134.50.3.210
Server/Host Found, E-Address = 0030487A9468
170 (128+42) bytes from 134.50.3.210: icmp_seq=0 time=179 us
Packets Transmitted =1, Packets Received =1, Packets Lost =0 (0%)
Round-Trip Min/Avg/Max = 179/179/179 uS

=== show the flash memory===

MVME6100> flashShow
Device-Name Base-Address,Size Device-Size,Count Boot Type
/dev/flash0 F4000000,04000000 02000000,00000002 No Intel 28F256
/dev/flash1 F8000000,04000000 02000000,00000002 Yes Intel 28F256

=== Load in the VxWorks boot kernel ===

MVME6100> tftpGet -cCLIENT_IP_ADDRESS -sSERVER_IP_ADDRESS -fFILENAME

CLIENT_IP_ADDESS is the IP address of the computer receiving the file 
SERVER_IP_ADDRESS is the IP address of the computer hosting the file (by default tftp uses the subdirectory /tftpboot) 

MVME6100> tftpGet -c134.50.3.216 -s134.50.3.210 -fboot6100_122.bin
Network Loading from: /dev/enet0
Loading File: boot6100_122.bin
Load Address: 006B7000
Download Buffer Size = 00200000

Client IP Address = 134.50.3.216
Server IP Address = 134.50.3.210
Gateway IP Address = 134.50.3.253
Subnet IP Address Mask = 255.255.255.0

Network File Load in Progress...

Bytes Received =&594768, Bytes Loaded =&594768
Bytes/Second =&594768, Elapsed Time =1 Second(s)

=== Flash the RAM with the program===

>MVME6100>flashProgram -d/dev/flash0 -o03f00100 -nfff00

MVME6100> flashProgram -d/dev/flash0 -o03f00100 -nfff00
Source Starting/Ending Addresses =006B7000/007B6EFF
Destination Starting/Ending Addresses =F7F00100/F7FFFFFF
Number of Effective Bytes =000FFF00 (&1048320)

Program Flash Memory (Y/N)? Y

=== set BOOTA dip switch===
After flashing you flip dipswitch #2 on S4 fo off and powercycle
I moved the dip switch on S4 labeled "BOOT A" to OFF

=== Error===
MVME6100> sysMotVpdInit: Unable to read Vital Product Data (VPD).
sysMotVpdInit: Unable to read Vital Product Data (VPD).

The above error results when the "Normal" dip switch on S4 is set to
"OFF". The S4 dipswitch are now set to

{| border="1" cellpadding="4"
|-
|Pin|| Name ||Setting
|-
|1|| NORM ENV||on
|-
|2 ||BOOT A ||off
|-
|3|| WPA ||on
|-
|4 ||WPB ||off
|}

=== The VxWorks Boot screen===

<pre>
VxWorks System Boot

Copyright 1984-2002 Wind River Systems, Inc.

CPU: Motorola MVME6100-0163 - MPC 7457
Version: VxWorks5.5.1
BSP version: 1.2/2
Creation date: Feb 2 2007, 16:49:27

Press any key to stop auto-boot...
7

[VxWorks Boot]:
</pre>

== Setting VxWorks Parameters==
=== view the boot parameters===

The parameters below were used on 5/21/09

<pre>
[VxWorks Boot]: p

boot device : geisc
unit number : 0
processor number : 0
host name : localdaq
file name : /home/daq/CODA/VXWorks/vx6100_v4.1
inet on ethernet (e) : 10.1.1.2
inet on backplane (b): 0
host inet (h) : 10.1.1.1
user (u) : daq
flags (f) : 0x20
target name (tn) : roc1
startup script (s) : /home/daq/CODA/bootscripts/roc1.boot

[VxWorks Boot]:
</pre>

=== set the boot parameters ===
<pre>

Typing a "c" will CONFIGURE the boot parameters

[VxWorks Boot]: c

'.' = clear field; '-' = go to previous field; ^D = quit

boot device : geisc0
processor number : 0
host name : daq1
file name : /home/daq/CODA/VXWorks/vx6100_v4.1
inet on ethernet (e) : 134.50.3.216
inet on backplane (b): 0
host inet (h) : 134.50.3.210
gateway inet (g) :
user (u) : daq
ftp password (pw) (blank = use rsh):
flags (f) : 0x20
target name (tn) : roc1
startup script (s) : /home/daq/CODA/bootscripts/roc1.boot
other (o) :
</pre>

The flag "0x20" tells VxWorks to disable the rlogin/telnet security so no username or password is required.

=== sample boot script===
# Boot file for CODA ROC 2.0
# PowerPC version

# up the sliding window
tcp_sendspace=0x8000
tcp_recvspace=0x8000

# Setup environment / load coda_roc
putenv "MSQL_TCP_HOST=daq1"
putenv "EXPID=LDS"
putenv "TCL_LIBRARY=/home/daq/CODA/2.5/common/lib/tcl7.4"
putenv "ITCL_LIBRARY=/home/daq/CODA/2.5/common/lib/itcl2.0"
putenv "DP_LIBRARY=/home/daq/CODA/2.5/common/lib/dp"
putenv "CMLOG_PORT=8102"
putenv "TOKEN_PORT=5555"
putenv "SESSION=daq"

# Download Message logging libraries/client
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogClientD
ld < /home/daq/CODA/2.5/CMLOG/2.1/lib/ppc-vw55/libcmlog.a
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogVxLogMsg
cd "/home/daq/CODA/2.5/VXWORKSPPC55/lib"
ld < libcamac.o

cd "/home/daq/CODA/2.5/VXWORKSPPC55/bin"
ld < coda_roc
ld < caSrvr

#cd "/home/daq/ROClibs"
#ld < adc1182_ppc.o
#ld < scale32Lib_ppc.o
#ld < pas9740Lib_ppc.o
#ld < sis3610Lib_ppc.o

# Spawn tasks
sp cmlogClientD
sp cmlogVxLogMsg
taskDelay (60*5)
# spawn the CAMAC remote server
taskSpawn "caServ",110,spTaskOptions,10000,caSrvr_main
# spawn the roc task
taskSpawn ("ROC",200,0x8,250000,coda_roc,"-i","-s","daq","-objects","roc1 ROC")

== Type "@" to reboot the ROC ==

<pre>
[VxWorks Boot]: @

boot device : geisc
unit number : 0
processor number : 0
host name : daq1
file name : /home/daq/CODA/VXWorks/vx6100_v4.1
inet on ethernet (e) : 134.50.3.216
inet on backplane (b): 0
host inet (h) : 134.50.3.210
user (u) : daq
flags (f) : 0x0
target name (tn) : roc1
startup script (s) : /home/daq/CODA/bootscripts/roc1.boot

Attached TCP/IP interface to geisc0.
Warning: no netmask specified.
Attaching network interface lo0... done.
Loading... 1784832
Starting at 0x100000...

Attached TCP/IP interface to geisc unit 0
Attaching interface lo0...done

Adding 5075 symbols for standalone.

]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003

CPU: Motorola MVME6100-0163 - MPC 7457. Processor #0.
Memory Size: 0x10000000. BSP version 1.2/2.
WDB Comm Type: WDB_COMM_END
WDB: Ready.
Executing startup script /home/daq/CODA/bootscripts/roc1.boot ...
# Boot file for CODA ROC 2.0
# PowerPC version

# up the sliding window
tcp_sendspace=0x8000
tcp_sendspace = 0x283a60: value = 32768 = 0x8000
tcp_recvspace=0x8000
tcp_recvspace = 0x283a64: value = 32768 = 0x8000

# Setup environment / load coda_roc
putenv "MSQL_TCP_HOST=daq1"
value = 0 = 0x0
putenv "EXPID=LDS"
value = 0 = 0x0
putenv "TCL_LIBRARY=/home/daq/CODA/2.5/common/lib/tcl7.4"
value = 0 = 0x0
putenv "ITCL_LIBRARY=/home/daq/CODA/2.5/common/lib/itcl2.0"
value = 0 = 0x0
putenv "DP_LIBRARY=/home/daq/CODA/2.5/common/lib/dp"
value = 0 = 0x0
putenv "CMLOG_PORT=8102"
value = 0 = 0x0
putenv "TOKEN_PORT=5555"
value = 0 = 0x0
putenv "SESSION=daq"
value = 0 = 0x0

# Download Message logging libraries/client
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogClientD
value = 231515072 = 0xdcca3c0
ld < /home/daq/CODA/2.5/CMLOG/2.1/lib/ppc-vw55/libcmlog.a
value = 231514544 = 0xdcca1b0
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogVxLogMsg
value = 231514016 = 0xdcc9fa0
cd "/home/daq/CODA/2.5/VXWORKSPPC55/lib"
value = 0 = 0x0
ld < libcamac.o
value = 231515648 = 0xdcca600 = camacLockKey + 0x260

cd "/home/daq/CODA/2.5/VXWORKSPPC55/bin"
value = 0 = 0x0
ld < coda_roc
value = 231495344 = 0xdcc56b0 = eventNumber + 0xd0
ld < caSrvr
value = 230293088 = 0xdb9fe60

#cd "/home/daq/ROClibs"
#ld < adc1182_ppc.o
#ld < scale32Lib_ppc.o
#ld < pas9740Lib_ppc.o
#ld < sis3610Lib_ppc.o

# Spawn tasks
sp cmlogClientD
task spawned: id = cmlogC0xlient Daemon uses db9a620default prior, name = ity 190
t1
value = cmlogClient 230270496daemon uses = 0x default stack db9a620size 20000

sp cmlogVxLogMsgcmlog
ClientD with task spawned: id = cmlogVx0xLogMsg uses defauldc10fb0t priority 19, name = 9
t2cmlog p
cmlogVxLogMsg uses value = default stac230756272k size 1000 = 0x0
dc10fb0rotoco
l version 2.xtaskDelay (60*5)

Waiting fCannot find any cmlog server running
or Cannot connect to a cmlog server
cmlogClStarting up cmlog client daemon....
ientD to start up
value = 0 = 0x0
# spawn the CAMAC remote server
taskSpawn "caServ",110,spTaskOptions,10000,caSrvr_main
value = 230877024 = 0xdc2e760
# spawn the roc task
taskSpawn ("ROC",200,0x8,250000,coda_roc,"-i","-s","daq","-objects","roc1 ROC")
value = 230148128 = 0xdb7c820

Args = -i -s daq -objects roc1 ROC
roc1

Done executing startup script /home/daq/CODA/bootscripts/roc1.boot

-> Connect: S_errno_EHOSTUNREACH
msql error : Can't connect to MSQL server on daq1
Connect: S_errno_EHOSTUNREACH
MSQL_Cmd_Connect: error 'cause socket < 0
msql: Can't connect to MSQL server on daq1

Now i need to install CODA and run the MSQL data base

</pre>

== ROC boot script==

<pre>
# Boot file for CODA ROC 2.0
# PowerPC version

# up the sliding window
tcp_sendspace=0x8000
tcp_recvspace=0x8000

# Setup environment / load coda_roc
putenv "MSQL_TCP_HOST=daq1"
putenv "EXPID=LDS"
putenv "TCL_LIBRARY=/home/daq/CODA/2.5/common/lib/tcl7.4"
putenv "ITCL_LIBRARY=/home/daq/CODA/2.5/common/lib/itcl2.0"
putenv "DP_LIBRARY=/home/daq/CODA/2.5/common/lib/dp"
putenv "CMLOG_PORT=8102"
putenv "TOKEN_PORT=5555"
putenv "SESSION=daq"

# Download Message logging libraries/client
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogClientD
ld < /home/daq/CODA/2.5/CMLOG/2.1/lib/ppc-vw55/libcmlog.a
ld < /home/daq/CODA/2.5/CMLOG/2.1/bin/ppc-vw55/cmlogVxLogMsg
#cd "/home/daq/CODA/2.5/VXWORKSPPC55/lib"
#ld < libcamac.o

cd "/home/daq/CODA/2.5/VXWORKSPPC55/bin"
ld < coda_roc
#ld < caSrvr

#cd "/home/daq/ROClibs"
#ld < adc1182_ppc.o
#ld < scale32Lib_ppc.o
#ld < pas9740Lib_ppc.o
#ld < sis3610Lib_ppc.o

# Spawn tasks
sp cmlogClientD
sp cmlogVxLogMsg
taskDelay (60*5)
# spawn the CAMAC remote server
taskSpawn "caServ",110,spTaskOptions,10000,caSrvr_main
# spawn the roc task
taskSpawn ("ROC",200,0x8,250000,coda_roc,"-i","-s","daq","-objects","roc1 ROC")

</pre>

==Installing CMLOG==

I copied the binary files at /site/coda/cmlog over to /home/daq/CODA/2.5

[http://wiki.iac.isu.edu/index.php/Data_Acquisition return to DAQ page]

MVME 6100 ROC - Revision history

Foretony: Created page with ' MVME 6100 ROC1 ethernet address: 0001AF1998B5 ROC1 ethernet address: 0001AF1998B6 MPC7457 RISC G4 processor (PPC family) == Download files from JLAB == I down…'

Foretony: Created page with ' MVME 6100
ROC1 ethernet address: 0001AF1998B5
ROC1 ethernet address: 0001AF1998B6
MPC7457 RISC G4 processor (PPC family)
== Download files from JLAB == I down…'