Lab 10 TF EIM - Revision history

Foretony: /* Full-Wave Rectifier Bridge Circuit */

2011-03-04T20:22:34Z

Full-Wave Rectifier Bridge Circuit

2011-03-04T20:22:19Z

Full-Wave Rectifier Circuit

2011-03-04T20:22:03Z

Half-Wave Rectifier Circuit

2011-03-04T19:07:02Z

2011-03-02T18:10:48Z

Full-Wave Rectifier Bridge Circuit

2011-03-02T18:10:04Z

Full-Wave Rectifier Bridge Circuit

2011-03-02T18:07:15Z

Full-Wave Rectifier Bridge Circuit

2011-03-02T18:05:09Z

Full-Wave Rectifier Bridge Circuit

2011-03-02T18:00:32Z

Full-Wave Rectifier Circuit

2011-03-02T17:58:28Z

Half-Wave Rectifier Circuit

← Older revision		Revision as of 20:22, 4 March 2011
Line 27:		Line 27:
	List the components below and show your instructor the output observed on the scope and sketch it below.		List the components below and show your instructor the output observed on the scope and sketch it below.

−	~~=Full-Wave Rectifier Bridge Circuit=~~
−
−	~~[[File:TF_EIM_Lab10_HW_RectifierBridge.png\| 400 px]]~~
−
−
−	~~1.) Choose R in the above circuit so the low-pass filter breakpoint is less than 60 Hz.~~
−
−	~~2.) Measure the quantities below using at least 4 different load resistors.~~
−
−
−
−	~~{\| border="3" cellpadding="20" cellspacing="0"~~
−	~~\|<math>R_L</math> \|\| <math>I_L</math> \|\| <math>P_L</math> \|\|<math>V_D</math> \|\|<math>V_{ripple}</math>~~
−	\|-
−	~~\| \|\| \|\| \|\| \|\|~~
−	\|-
−	~~\| \|\| \|\| \|\| \|\|~~
−	\|-
−	~~\| \|\| \|\| \|\| \|\|~~
−	\|-
−	~~\| \|\| \|\| \|\| \|\|~~
−	\|-
−	\|}
−
−	~~<math>P_L</math> = power dissipated by the load resistor (don't exceed resistor power rating)~~
−
−	~~<math>V_D</math> = output voltage~~
−
−	~~3.) Explain why the ripple amplitude increases as I_L increases.~~

	[[Forest_Electronic_Instrumentation_and_Measurement]]		[[Forest_Electronic_Instrumentation_and_Measurement]]

@@ Line 25: / Line 25: @@
 Determine the components needed in order to make the above circuit's output ripple have a <math>\Delta V</math> less than 0.5 Volt.
-List the components below and show your instructor the output observed on the scope.
+List the components below and show your instructor the output observed on the scope and sketch it below.
 =Full-Wave Rectifier Bridge Circuit=

@@ Line 18: / Line 18: @@
 Determine the components needed in order to make the output ripple have a <math>\Delta V</math> less than 1 Volt.
-List the components below and show your instructor the output observed on the scope.
+List the components below and show your instructor the output observed on the scope and sketch it below.
 =Full-Wave Rectifier Circuit=

@@ Line 40: / Line 40: @@
 |<math>R_L</math> ||  <math>I_L</math> || <math>P_L</math> ||<math>V_D</math> ||<math>V_{ripple}</math>
 |-
-| || ||  ||
+| || ||  || ||
 |-
-| || ||  ||
+| || ||  || ||
 |-
-| || ||  ||
+| || ||  || ||
 |-
-| || ||  ||
+| || ||  || ||
 |-
 |}
 <math>P_L</math> = power dissipated by the load resistor (don't exceed resistor power rating)
 <math>V_D</math> = output voltage

@@ Line 38: / Line 38: @@
 {| border="3"  cellpadding="20" cellspacing="0"
-|R_L || V_D || I_L || V_{ripple}
+|<math>R_L</math> ||  <math>I_L</math> || <math>P_L</math> ||<math>V_D</math> ||<math>V_{ripple}</math>
 |-
 | || ||  ||
@@ Line 50: / Line 50: @@
 |}
+.) Explain why the ripple amplitude increases as I_L increases.
 [[Forest_Electronic_Instrumentation_and_Measurement]]

← Older revision		Revision as of 18:07, 2 March 2011
Line 34:		Line 34:

	2.) Measure the quantities below using at least 4 different load resistors.		2.) Measure the quantities below using at least 4 different load resistors.
		+
		+
		+
		+	{\| border="3" cellpadding="20" cellspacing="0"
		+	\|R_L \|\| V_D \|\| I_L \|\| V_{ripple}
		+	\|-
		+	\| \|\| \|\| \|\|
		+	\|-
		+	\| \|\| \|\| \|\|
		+	\|-
		+	\| \|\| \|\| \|\|
		+	\|-
		+	\| \|\| \|\| \|\|
		+	\|-
		+	\|}
		+



	[[Forest_Electronic_Instrumentation_and_Measurement]]		[[Forest_Electronic_Instrumentation_and_Measurement]]

← Older revision		Revision as of 18:05, 2 March 2011
Line 29:		Line 29:

	[[File:TF_EIM_Lab10_HW_RectifierBridge.png\| 400 px]]		[[File:TF_EIM_Lab10_HW_RectifierBridge.png\| 400 px]]
		+
		+
		+	1.) Choose R in the above circuit so the low-pass filter breakpoint is less than 60 Hz.
		+
		+	2.) Measure the quantities below using at least 4 different load resistors.
		+


	[[Forest_Electronic_Instrumentation_and_Measurement]]		[[Forest_Electronic_Instrumentation_and_Measurement]]

@@ Line 12: / Line 12: @@
 .)Consider building circuit below.
 [[File:TF_EIM_Lab10_HW_Rectifier.png| 400 px]]
-You will need to determine the components needed in order to make the output ripple have a \Delta V less than
+Determine the components needed in order to make the output ripple have a <math>\Delta V</math> less than 1 Volt.
 =Full-Wave Rectifier Circuit=