Gumstix - Revision history

Nickbenj: /* Setting Static IP adress */

2012-11-12T21:43:22Z

Setting Static IP adress

2010-06-03T01:57:06Z

cgi-bin programs

2010-05-18T02:03:57Z

Hardware

2010-05-17T23:00:08Z

Setting Static IP adress

2010-05-17T22:58:40Z

Setting Static IP adress

2010-01-30T15:46:38Z

Setting Static IP adress

2010-01-30T15:46:23Z

Setting the date

2009-09-15T21:53:13Z

2009-09-15T21:31:22Z

Hardware

2009-09-12T00:26:18Z

@@ Line 40: / Line 40: @@
 auto eth0
 iface eth0 inet static
          address 134.50.3.175
          netmask 255.255.255.0
-         network 134.50.254.5
+         network 134.50.3.0
-broadcast 134.50.3.255
+        broadcast 134.50.3.255
 </pre>
@@ Line 106: / Line 111: @@
 Genmask   >>> netmask
 Gateway   >>> gateway

@@ Line 20: / Line 20: @@
 [http://www.boa.org Boa Webserver] is the webserver on the Gumstix.<br/>
 [http://www.gnu.org/software/cgicc/ cgicc] is the C++ library used for handling web scripts.<br/>
 ===Tutorials===

@@ Line 4: / Line 4: @@
 (2)The 80 pin expansion socket is attached to a [http://www.gumstix.com/store/catalog/product_info.php?products_id=207 network interface card] for TCP/IP networking.
 <br/>
-(3)The 60 pin expansion socket has a [http://www.gumstix.com/store/catalog/product_info.php?products_id=184 breakout-vx] card to allow access to the I2C signals, serial ports, and various other GPIO possibilities.
+(2)The 60 pin expansion socket has a [http://www.gumstix.com/store/catalog/product_info.php?products_id=184 breakout-vx] card to allow access to the I2C signals, serial ports, and various other GPIO possibilities.
 <br/>
-(2)Additionally, [http://www.gumstix.com/store/catalog/product_info.php?products_id=148 4V power adapters]
+(1)Additionally, [http://www.gumstix.com/store/catalog/product_info.php?products_id=148 4V power adapters]
 <br/>
-(10)screw and spacer [http://www.gumstix.com/store/catalog/product_info.php?products_id=161 kits] are needed.
+(3)[http://www.acroname.com/robotics/parts/S13-SERIAL-INT-CONN.html TTL to serial adapters]
-<br/>
 ===Software===
 [http://docwiki.gumstix.org/Main_Page Gumstix Documentation Wiki]<br/>

@@ Line 37: / Line 37: @@
 ===Setting Static IP adress===
-In the LDS we use
+In the LDS use the static method modifiy the file etc/network/interfaces so it says
 <pre>
@@ Line 49: / Line 49: @@
-Use the static method modifiy the file tc/network/interfaces so it says
+For JLab Use the static method modifiy the file etc/network/interfaces so it says
 <pre>
@@ Line 78: / Line 78: @@
 </pre>

← Older revision		Revision as of 22:58, 17 May 2010
Line 36:		Line 36:

	===Setting Static IP adress===		===Setting Static IP adress===
		+
		+	In the LDS we use
		+
		+	<pre>
		+	auto eth0
		+	iface eth0 inet static
		+	address 134.50.3.175
		+	netmask 255.255.255.0
		+	network 134.50.254.5
		+	broadcast 134.50.3.255
		+	</pre>
		+

	Use the static method modifiy the file tc/network/interfaces so it says		Use the static method modifiy the file tc/network/interfaces so it says

@@ Line 73: / Line 73: @@
 ifdown
 ifup eth0
-</ore>
+</pre>
 Must check the if address of a machine which is connected to the same network by ifconfig and route -n

← Older revision		Revision as of 15:46, 30 January 2010
Line 34:		Line 34:
	ssh root@134.50.203.56 "echo date -s `date +%m%d%H%M%Y`"		ssh root@134.50.203.56 "echo date -s `date +%m%d%H%M%Y`"
	</pre>		</pre>
		+
		+	===Setting Static IP adress===
		+
		+	Use the static method modifiy the file tc/network/interfaces so it says
		+
		+	<pre>
		+
		+	# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
		+
		+	# The loopback interface
		+	#
		+	auto lo
		+	iface lo inet loopback
		+
		+	#
		+	# Wired interfacesq
		+	#
		+	auto eth0
		+	iface eth0 inet static
		+	address 129.57.36.61
		+	#network 129.57.1.0
		+	gateway 129.57.36.1
		+	netmask 255.255.252.0
		+	broadcast 129.57.39.255
		+
		+	# if netduo attached uncomment lines below
		+	#auto eth1
		+	#iface eth1 inet dhcp
		+
		+	#
		+
		+
		+	</pre>
		+
		+	Then do commands
		+
		+	<pre>
		+	ifdown
		+	ifup eth0
		+	</ore>
		+
		+	Must check the if address of a machine which is connected to the same network by ifconfig and route -n
		+
		+
		+	ifconfig interfaces
		+	inet addr >>> address
		+	Bcast >>> broadcast
		+
		+	route -n
		+	Genmask >>> netmask
		+	Gateway >>> gateway

@@ Line 1: / Line 1: @@
-The gumstix motherboard used is the [http://www.gumstix.com/store/catalog/product_info.php?products_id=178 verdex XL6P]. It has a 600MHz Marvell XScale processor, 128MB of RAM, and 32MB of flash.
+===Hardware===
 <br/>
-The 120 pin expansion socket has a [http://gumstix.com/store/catalog/product_info.php?products_id=183 netCF-vx] network interface card for TCP/IP networking. This card also has a Compact Flash slot should additional storage be required.
+The 80 pin expansion socket is attached to a [http://www.gumstix.com/store/catalog/product_info.php?products_id=207 network interface card] for TCP/IP networking.
 <br/>
-The 60 pin expansion socket has a [http://gumstix.com/store/catalog/product_info.php?products_id=184 breakout-vx] card to allow access to the I2C signals, serial ports, and various other GPIO possibilities.
+The 60 pin expansion socket has a [http://www.gumstix.com/store/catalog/product_info.php?products_id=184 breakout-vx] card to allow access to the I2C signals, serial ports, and various other GPIO possibilities.
+<br/>
+Additionally, [http://www.gumstix.com/store/catalog/product_info.php?products_id=148 4V power adapters] and screw and spacer [http://www.gumstix.com/store/catalog/product_info.php?products_id=161 kits] are needed.
-==Links==
+===Software===
 [http://docwiki.gumstix.org/Main_Page Gumstix Documentation Wiki]<br/>
 ====I2C installation====