201403 R1ProgressRep - Revision history

Conedavi: /* March 28 2014 */

2014-03-28T05:00:00Z

March 28 2014

2014-03-27T02:30:20Z

March 26 2014

2014-03-25T22:41:49Z

March 24 2014

2014-03-24T21:02:20Z

March 24 2014

2014-03-24T21:01:42Z

March 24 2014

2014-03-24T06:48:05Z

March 22 2014

2014-03-23T04:10:06Z

March 22 2014

2014-03-23T03:56:31Z

March 20 2014

2014-03-23T03:51:58Z

March 20 2014

2014-03-21T16:15:49Z

March 28 2014

← Older revision		Revision as of 05:00, 28 March 2014
Line 123:		Line 123:
	The man lifts, A-fram and any other equipment goes in the shops area across the loading dock driveway.		The man lifts, A-fram and any other equipment goes in the shops area across the loading dock driveway.

		+
		+	Shipping Manifest:
		+	* S1
		+	* S2
		+	* 1x A-Frame
		+	* 2x Magnet rails
		+	* 2x DC magnets
		+	* 2x Scissor-lifts with wheels removed. Charging cord in the lift.


	[[CLAS12_R1_Progress_Reports#March_2014]]		[[CLAS12_R1_Progress_Reports#March_2014]]

@@ Line 97: / Line 97: @@
 =March 26 2014=
-Strap both blue man lifts onto separate pallets.
+* A-frame is on a palette and ready for the crane in the loading dock.
 =March 27 2014=

@@ Line 87: / Line 87: @@
 * SL2 passed HV test - current is steady at <0.1 microamps once up to 100(sense)/50(field)/20V(guard) for whole superlayer when connected with kraken. No crossed wires - no voltage leaking over from one wire type to another.
-HV test passed, && Dust covers are one:
+HV test passed, && Dust covers are done:
 Goal: Finish boxing up drift chamber so they are ready to be mount onto the pallets (check that they go into the boots)

@@ Line 85: / Line 85: @@
 =March 24 2014=
-* SL2 passed HV test - current is steady at <0.1 microamps once up to 100(sense)/50(field)/20V(guard) for whole superlayer when connected with kraken.
+* SL2 passed HV test - current is steady at <0.1 microamps once up to 100(sense)/50(field)/20V(guard) for whole superlayer when connected with kraken. No crossed wires - no voltage leaking over from one wire type to another.
 HV test passed, && Dust covers are one:

@@ Line 85: / Line 85: @@
 =March 24 2014=
-If HV test passed, && Dust covers are one:
+* SL2 passed HV test - current is steady at <0.1 microamps once up to 100(sense)/50(field)/20V(guard) for whole superlayer when connected with kraken.
 Goal: Finish boxing up drift chamber so they are ready to be mount onto the pallets (check that they go into the boots)

@@ Line 77: / Line 77: @@
 * Gas flow to S1 isn't inflating it. Appears that the secondary line that went to another chamber is not plugged / cut off, so we may just be venting ArgCO2 into the room. Also, the out-going tube from the flow controller (that connects to a T-junction for both chamber gas flows) had its shut-off valve turned to the "off" position (probably inadvertent), so no gas was flowing anywhere. The pressure in the ArgCO2 tank is still at 2100 psi.
 Changed the T-junction connections so the shut-off valve will cut-off the secondary line's access to gas flow, and turned it to the "off" position. Turned up flow-rate to 85.
 =March 24 2014=

@@ Line 47: / Line 47: @@
 =March 20 2014=
-* Wire wrap is ~100% done
+* Wire wrap is ~85% done
 * All suspension boots installed on pallets. A-frame pallet is finished.
 Remaining tasks:
 HV Testing
@@ Line 67: / Line 69: @@
 * Organize miscellaneous lab materials for shipping back to J-lab on pallets. (need the metal-strap crimping device back)
 - Put padding/bubble-wrap back on the extra set of HV boards we didn't install before shipping.
 =March 24 2014=

@@ Line 103: / Line 103: @@
 Two drift chambers go on the loading dock in the same spot used last time
-The man lifts, A-fram and any other equipment goes in the shops area across the driveway front eh loading dock.
+The man lifts, A-fram and any other equipment goes in the shops area across the  loading dock driveway.
 [[CLAS12_R1_Progress_Reports#March_2014]]